Table of Contents
Advertisement
Quick Links
Please dispose of packaging for the product in a responsible
manner. It is suitable for recycling. Help to protect the
environment, take the packaging to the local amenity tip
and place into the appropriate recycling bin.
Never dispose of electrical equipment or batteries in with
your domestic waste. If your supplier offers a disposal facili-
ty please use it or alternatively use a recognised re-cycling
agent. This will allow the recycling of raw materials and help
protect the environment.
FOR HELP OR ADVICE ON THIS PRODUCT PLEASE CONTACT YOUR DISTRIBUTOR,
OR SIP DIRECTLY ON:
TEL: 01509500400
EMAIL: sales@sip-group.com or technical@sip-group.com
www.sip-group.com
Ref: 170713
36
8" Swivel
Metal Cutting Bandsaw
01593
Please read and fully understand the instructions in this manual
before operation. Keep this manual safe for future reference.
1
Advertisement
Table of Contents
Related Manuals for SIP 01593
Summary of Contents for SIP 01593
- Page 1 This will allow the recycling of raw materials and help protect the environment. FOR HELP OR ADVICE ON THIS PRODUCT PLEASE CONTACT YOUR DISTRIBUTOR, OR SIP DIRECTLY ON: TEL: 01509500400 01593 EMAIL: sales@sip-group.com or technical@sip-group.com www.sip-group.com...
-
Page 2: Declaration Of Conformity
LE12 9NH England As the manufacturer's authorised representative within the EC declare that the 8” Swivel Metal Cutting Bandsaw 1ph - SIP Pt. No. 01593 Conforms to the requirements of the following directive(s), as indicated. 2006/95/EC Low Voltage Directive 2004/108/EC... -
Page 3: Table Of Contents
NOTES NOTES CONTENTS Page No. Description Safety Symbols Used Throughout This Manual Safety Instructions Electrical Connection Guarantee Technical Specifications Contents & Accessories Getting to Know Your Bandsaw Assembly Instructions Operating Instructions Maintenance Instructions Troubleshooting Wiring Diagram Exploded Diagram Parts List Declaration of Conformity... -
Page 4: Safety Symbols Used Throughout This Manual
SAFETY SYMBOLS USED THROUGHOUT THIS MANUAL NOTES NOTES Danger / Caution: Indicates risk of personal injury and/or the possibility of damage. Warning: Risk of electrical injury or damage! Note: Supplementary information. SAFETY INSTRUCTIONS IMPORTANT: Please read the following instructions carefully, failure to do so could lead to serious personal injury and / or damage to the band- saw. - Page 5 NOTES NOTES SAFETY INSTRUCTIONS….cont supply. KEEP WORK AREA CLEAN AND WELL LIT: Cluttered work areas and dark areas invite ac- cidents. Floors must not be slippery due to oil, water or sawdust etc. HAVE YOUR BANDSAW REPAIRED BY A QUALIFIED PERSON: The bandsaw is in accord- ance with the relevant safety requirements.
- Page 6 NOTES PARTS LIST….cont nance. Ref. No. Description SIP Part No. Ref. No. Description SIP Part No. Keep hands and all other body parts away from the blade. Turn the bandsaw off and disconnect it from the mains supply when moving from 275.
- Page 7 PARTS LIST….cont SAFETY INSTRUCTIONS….cont cause the blade to slip, DO NOT cut such items without clamping or blocking the Ref. No. Description SIP Part No. Ref. No. Description SIP Part No. material. DO NOT start the bandsaw until the material is secure and the blade has been low- 181.
-
Page 8: Electrical Connection
WK04-00018 159. Worm gear WK04-00118 This SIP bandsaw is fitted with a standard 230v ~ 13 amp type plug. Before using the bandsaw, inspect the mains lead and plug to ensure that neither are damaged. If 137. Right guide holder WK04-00095 160. -
Page 9: Guarantee
Bolt M10x40 WK04-00056 110. Washer M6 WK04-00011 This SIP bandsaw is covered by a 12 month parts and labour warranty covering failure Nut M10 WK04-00052 111. Bolt M6x16 WK04-00010 due to manufacturers defects. This does not cover failure due to misuse or operating... -
Page 10: Getting To Know Your Bandsaw
GETTING TO KNOW YOUR BANDSAW EXPLODED DIAGRAM….cont SAW BASE... - Page 11 EXPLODED DIAGRAM GETTING TO KNOW YOUR BANDSAW….cont SAW BOW Ref. Description Ref. Description Switch Vice base Emergency stop button Tension spring Gearbox Pivot arm Belt / Pulley guard Blade cover Motor Vice stop Right adjustable guide bracket Lever lock Hydraulic Ram Cut off stop (hole) Electrical box Vice hand-wheel...
- Page 12 TECHNICAL SPECIFICATION WIRING DIAGRAM Name 8” Swivel Metal Cutting Bandsaw Part Number 01593 Input Voltage 230v ~ 50Hz Circular 45˚ 127mm Circular 0˚ 178mm Rectangle 45˚ 85 x 140mm Rectangle 0˚ 178 x 210mm Blade Speed 22, 33, 45 & 65 mtr/min Blade Size 2362 x 0.9 x 19mm...
-
Page 13: Assembly Instructions
TROUBLESHOOTING ASSEMBLY INSTRUCTIONS UNPACKING Symptom Possible cause Solution Remove the bandsaw from the packaging, check the bandsaw for any signs of 1. Blade guides are worn. 1. Replace blade guides. damage or missing items prior to assembling. Unusual wear on side or 2. -
Page 14: Operating Instructions
ASSEMBLY INSTRUCTIONS….cont MAINTENANCE INSTRUCTIONS….cont thinner or lacquer thinner as these will damage the painted surfaces. Note: The outer bearing shaft is eccentric and is the one to adjust, the inner bearing shaft is fixed and can not be adjusted. REMOVING THE TRANSIT BOLT Note: Never attempt to adjust the blade guide bearings whilst the ma- Before the bandsaw can be used the transit bolt and chine is running, ALWAYS disconnect from the mains supply before pro-... - Page 15 MAINTENANCE INSTRUCTIONS….cont OPERATING INSTRUCTIONS….cont SETTING THE BLADE SQUARE TO THE BED AT 0˚ Ensure the bow is at its lowest position. Speed Speed Speed Speed Set square Material M/Min Material M/Min Material M/Min Material M/Min Disconnect from the mains supply. (FPM) (FPM) (FPM)
- Page 16 OPERATING INSTRUCTIONS….cont MAINTENANCE INSTRUCTIONS….cont Blade tension is important for the correct operation of the bandsaw; the blade tension OPERATING THE VICE should be set between 700-900kgs. Setting The Vice For Maximum Width Cutting at 0˚: To set the blade correctly without using a blade tension gauge, take the following Cap head bolt steps.
-
Page 17: Maintenance Instructions
MAINTENANCE INSTRUCTIONS OPERATING INSTRUCTIONS….cont Setting The Vice For Angled Cuts: CHAINGING THE BLADE Note: When the vice assembly is set at the angle cutting position you will Caution: Before carrying out any maintenance always disconnect the lose the maximum width cutting capacity. bandsaw from the mains supply. - Page 18 OPERATING INSTRUCTIONS….cont OPERATING INSTRUCTIONS….cont USING THE COOLANT PUMP CUTTING WITH THE BANDSAW Note: We recommend the use of water soluble coolant, this will prolong Danger: Before attempting to cut always make sure all covers are on and the blade life and make the cut more efficient. secure.
Need help?
Do you have a question about the 01593 and is the answer not in the manual?
Questions and answers