Tektronix MTM400 Technical Reference
Tektronix MTM400 Technical Reference

Tektronix MTM400 Technical Reference

Mpeg transport stream monitor
Hide thumbs Also See for MTM400:
Table of Contents

Advertisement

Quick Links

Technical Reference
MTM400
MPEG Transport Stream Monitor
071-1560-04
This document applies to firmware versions
1.2 to 2.6.
Warning
The servicing instructions are for use by qualified
personnel only. To avoid personal injury, do not
perform any servicing unless you are qualified to
do so. Refer to all safety summaries prior to
performing service.
www.tektronix.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MTM400 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Tektronix MTM400

  • Page 1 Technical Reference MTM400 MPEG Transport Stream Monitor 071-1560-04 This document applies to firmware versions 1.2 to 2.6. Warning The servicing instructions are for use by qualified personnel only. To avoid personal injury, do not perform any servicing unless you are qualified to do so.
  • Page 2 Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or suppliers, and are protected by national copyright laws and international treaty provisions. Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes that in all previously published material.
  • Page 3: Table Of Contents

    ........3−6 MTM400 MPEG Transport Stream Monitor Technical Reference...
  • Page 4 ......... . . 4−19 Glossary MTM400 MPEG Transport Stream Monitor Technical Reference...
  • Page 5 ....4−15 Figure 4−13: Cable connections for GbE interface board ... . 4−16 MTM400 MPEG Transport Stream Monitor Technical Reference...
  • Page 6 ..... 1−19 Table 1−31: Transport stream board batteries ..... 1−19 MTM400 MPEG Transport Stream Monitor Technical Reference...
  • Page 7 ..... 4−9 Table 4−3: GbE interface board connectors ..... . 4−10 MTM400 MPEG Transport Stream Monitor Technical Reference...
  • Page 8 Table of Contents MTM400 MPEG Transport Stream Monitor Technical Reference...
  • Page 9 Do Not Operate in an Explosive Atmosphere. Keep Product Surfaces Clean and Dry. Provide Proper Ventilation. Refer to the manual’s installation instructions for details on installing the product so it has proper ventilation. MTM400 MPEG Transport Stream Monitor Technical Reference...
  • Page 10 WARNING indicates an injury hazard not immediately accessible as you read the marking. CAUTION indicates a hazard to property including the product. Symbols on the Product. The following symbols may appear on the product: CAUTION Protective Ground Refer to Manual (Earth) Terminal MTM400 MPEG Transport Stream Monitor Technical Reference viii...
  • Page 11: Service Safety Summary

    Disconnect power, remove battery (if applicable), and disconnect test leads before removing protective panels, soldering, or replacing components. To avoid electric shock, do not touch exposed connections. Use only Tektronix approved components when servicing the unit. MTM400 MPEG Transport Stream Monitor Technical Reference...
  • Page 12 Service Safety Summary MTM400 MPEG Transport Stream Monitor Technical Reference...
  • Page 13 Transport Stream Monitor: H Specifications lists the electrical, physical and environmental specifications of the MTM400 monitor. H Test Parameters describes the tests performed by the MTM400 monitor; it also describes the associated parameters. This section provides the following cross-referenced information: H The Standards Tests section (page 2−3) identifies the tests and event...
  • Page 14 071-1375-xx) specifies the remote control and status monitoring interfaces available to a management application. This English language reference document is available only from the Tektronix Web site (www.tektro- nix.com). The following URLs access the Web sites for the standards organizations listed (the URLs listed were valid at the time of writing): H MPEG−2 standards (International Organization for Standards)
  • Page 15 Specifications...
  • Page 17: Table 1−1: Remote User Interface Platform Characteristics

    Specifications This section lists the electrical, environmental, and physical specifications of the MTM400 system. All specifications are guaranteed unless labeled typical. Typical specifications are provided for your convenience and are not guaranteed. Electrical characteristics apply to test systems operating within the environmen- tal conditions.
  • Page 18: Table 1−3: Ts Processor - Asi Interface

    Same as the SMPTE310M input Signal Amplitude 600 mV min, 1.0 V max, into a 75 ohm load Output Impedance 75 ohms, transformer coupled Return Loss 10 dB min at 20 MHz MTM400 MPEG Transport Stream Monitor Technical Reference 1−2...
  • Page 19: Table 1−5: I/O Port Characteristics - Qpsk (L-Band)

    75 ohm nominal Input Return Loss 6 dB min, 10 dB typical, 51 MHz to 858 MHz Loop Through Power Gain 1.5 dB to 4 dB typical, 51 MHz to 858 MHz typical MTM400 MPEG Transport Stream Monitor Technical Reference 1−3...
  • Page 20: Table 1−7: I/O Port Characteristics - Itu-J83 Annex B Qam

    38 dB typical, with a 64 QAM input Receiver Bandwidth, QAM C 6 MHz nominal Input Termination Impedance 75 ohm nominal Input Return Loss 6 dB min, 10 dB typical, 88 MHz to 858 MHz MTM400 MPEG Transport Stream Monitor Technical Reference 1−4...
  • Page 21: Table 1−9: Baseband Board - Asi Interface

    Same as the SMPTE310M input Signal Amplitude 600 mV min, 1.0 V max, into a 75 ohm load Output Impedance 75 ohms, transformer coupled Return Loss 10 dB min at 20 MHz MTM400 MPEG Transport Stream Monitor Technical Reference 1−5...
  • Page 22: Table 1−11: Qpsk/8Psk Interface Board Characteristics With Qpsk Input

    17.6 kHz min, 26.4 kHz max (22 kHz "20%) LNB 22 kHz Signaling Frequency LNB 22 kHz Signaling Amplitude 600 mV p-p with 100 ohm load Ultimate Modulation Error Ratio (with equalizer) 26 dB with equalizer MTM400 MPEG Transport Stream Monitor Technical Reference 1−6...
  • Page 23: Table 1−12: Qpsk/8Psk Interface Board Characteristics With 8Psk Input

    Post RS BER and TEF (Transport Error Flag) Post Reed Solomon BER (TEF ratio), TEF rate, and number of Transport Error Flags (TEF count) are displayed. Constellation The RF constellation is displayed. MTM400 MPEG Transport Stream Monitor Technical Reference 1−7...
  • Page 24: Table 1−14: Cofdm Interface Board Characteristics

    1/2, 2/3, 3/4, 5/6, 7/8 Guard Intervals 1/32, 1/16, 1/8, 1/4 Spectrum Polarity The receiver will operate with both inverted and normal spectral polarity. w 37 dB with equalizer; typical Ultimate Modulation Error Ratio, with Equalizer MTM400 MPEG Transport Stream Monitor Technical Reference 1−8...
  • Page 25: Table 1−15: Cofdm Measurements

    1% to w 30% rms, for QPSK v 1% to w 20% rms, 16QAM v 1% to w 8.5% rms, 64QAM Resolution: 0.1% Accuracy: 1% (1 EVM unit), and additional "20% of reading MTM400 MPEG Transport Stream Monitor Technical Reference 1−9...
  • Page 26: Table 1−16: 8Vsb Board Characteristics

    −60 dBm to ensure compliance to EN 55103-2 immunity Modulation Format 8VSB in accordance with ATSC A/53B. Receiver Bandwidth 6 MHz Input Termination Impedance 75 ohm nominal Connector Type F type Input Return Loss 5 dB minimum; typical MTM400 MPEG Transport Stream Monitor Technical Reference 1−10...
  • Page 27: Table 1−17: 8Vsb Measurements

    Echo Profile (Typical) Equalizer filter tap information is displayed. Display Echo Level range: Normalized real tap values over the range of −1 to 1 Display Delay range: −6.7 μs to 45.5 μs MTM400 MPEG Transport Stream Monitor Technical Reference 1−11...
  • Page 28: Table 1−18: Qam Annex B Board Characteristics

    Receiver Bandwidth, QAM B 6 MHz nominal Connector Type F type Input Termination Impedance 75 ohm nominal Input Return Loss 5 dB typical w37 dB with equalizer; typical Ultimate Modulation Error Ratio with Equalizer MTM400 MPEG Transport Stream Monitor Technical Reference 1−12...
  • Page 29: Table 1−19: Qam Annex B Measurements

    Table 1−20: Video over IP board - Ethernet electrical port Characteristic Description Standard 10/100/1000BASE-T IEEE 802.3 Connector Type RJ-45 Data Format 10/100 Base T Data Format 1000 Base T Trellis encoded, PAM5 symbols full-duplex on 4-pair Cat-5 UTP per IEEE 802.3ab MTM400 MPEG Transport Stream Monitor Technical Reference 1−13...
  • Page 30: Table 1−21: Video Over Ip Board - General

    Smoothing mechanism for the TS packets before retransmitting packets out on ASI port Signal Amplitude 600 mV pk to pk min, 1.0V max into a 75 ohm load Return Loss 10 dB min at 270 MHz MTM400 MPEG Transport Stream Monitor Technical Reference 1−14...
  • Page 31: Table 1−24: Video Over Ip Board - Smpte310M Input - Loop-Through To Asi Output Bnc

    Ethernet Optical Transmitter - Multimode 850nm Using Tek supplied SFP module Output Power −9.5 dBm to −2 dBm; typical Center Wavelength - 850 nm 830 nm Min, 850 nm Typ, 860 nm Ma; typical MTM400 MPEG Transport Stream Monitor Technical Reference 1−15...
  • Page 32 Ethernet Optical Receiver - Multimode 850nm Using Tek supplied SFP module −12 Optical Input Power −17 dBm to 0 dBm, BER 1 X 10 ; typical 770 nm = λ = 860 nm Input Wavelength MTM400 MPEG Transport Stream Monitor Technical Reference 1−16...
  • Page 33: Table 1−26: Ts Processor - Alarm Connector

    Relay 1: Normally open contact RL2NO Relay 2: Normally open contact RL3NO Relay 3: Normally open contact RL4NO Relay 4: Normally open contact RL5NO Relay 5: Normally open contact Connector shell - Chassis ground MTM400 MPEG Transport Stream Monitor Technical Reference 1−17...
  • Page 34: Table 1−27: Ts Processor - Alarms

    Linear time code, SMPTE standard to ANSI/SMPTE 12M - 1995 Input Voltage 2.0 V p-p differentially minimum Table 1−29: TS processor - Ethernet RJ-45 connector Characteristic Description Connector 10/100 Base-T; RJ-45 Use only good quality screened cable; Cat 6 MTM400 MPEG Transport Stream Monitor Technical Reference 1−18...
  • Page 35: Table 1−30: Ac Power Source Characteristics

    2 (In single carrier) Voltage Capacity 210 mAh Continuous Discharge (Maximum) 3 mA Overall Dimensions (Single cell) Height 3.2 mm (0.13 in) Width (Diameter) 20 mm (0.79 in) Battery Type Tektronix part number: 146-0096-xx MTM400 MPEG Transport Stream Monitor Technical Reference 1−19...
  • Page 36: Environmental Characteristics

    Top and bottom: 0 mm; Sides: Standard 19 in rack mount Weight 6.0 kg (13.3 lbs); fully loaded Packaged Dimensions Height 241 mm (9.5 in) Width 590 mm (23.1 in) Depth 760 mm (30 in) Weight (Packaged) 9 kg (19.7 lbs) MTM400 MPEG Transport Stream Monitor Technical Reference 1−20...
  • Page 37: Certifications And Compliances

    U.S. Nationally Recognized Testing Laboratory UL61010B-1 Equipment for Measurement Use: Part 1: General Requirements. Listing Canadian Certification CAN/CSA C22.2 No. 1010.1 Safety requirements for electrical equipment for measurement, control, and laboratory use. MTM400 MPEG Transport Stream Monitor Technical Reference 1−21...
  • Page 38 Pollution Degree 4 Pollution that generates persistent conductivity through conductive dust, rain, or snow. Typical outdoor locations. Pollution Degree Pollution Degree 2 (as defined in IEC61010-1). Rated for indoor use only. MTM400 MPEG Transport Stream Monitor Technical Reference 1−22...
  • Page 39: Table 1−35: Environmental Limits And Use Classification For Safety Certification Compliance

    Mains fuse is 3.15 A, 250 V, Fast; Not operator replaceable. Refer servicing to qualified service personnel. Current Rating 1 Amp Pollution Degree Pollution Degree 2 (as defined in IEC 61010-1) Note: Rated for indoor use only. MTM400 MPEG Transport Stream Monitor Technical Reference 1−23...
  • Page 40 Specifications MTM400 MPEG Transport Stream Monitor Technical Reference 1−24...
  • Page 41 Test Parameters...
  • Page 43 H Event Traps tables (page 2−187) lists the SNMP (Simple Network Manage- ment Protocol) traps available for each event. NOTE. Event identities referred to in this section are relevant to all Tektronix MPEG monitoring products. MTM400 MPEG Transport Stream Monitor Technical Reference...
  • Page 44 Test Parameters - Standards Tests MTM400 MPEG Transport Stream Monitor Technical Reference 2−2...
  • Page 45: Standard Tests

    2.3.a PCR Repetition : EventID = 3150 PID Test : 2.3.a PCR Repetition : EventID = 3117 2.3.b PCR Discontinuity Indicator : EventID = 3151 PID Test : 2.3.b PCR Discontinuity Indicator : EventID = 3118 MTM400 MPEG Transport Stream Monitor Technical Reference 2−3...
  • Page 46 RF Test : MER Drift Limit : Event ID = 3802 : Metric ID = 2 RF Test : EVM : Event ID = d002 : Metric ID = 3 RF Test : EVM Limit : Event ID = 3803 : Metric ID = 3 MTM400 MPEG Transport Stream Monitor Technical Reference 2−4...
  • Page 47 Template ServiceType error : EventID = 6120 Template ServiceName error : EventID = 6130 Template Service constraint error : EventID = 6140 Template OtherPidsAllowed error : EventID = 6150 Any Template PID Error : EventID = 6200 MTM400 MPEG Transport Stream Monitor Technical Reference 2−5...
  • Page 48: Dvb Tests

    3.2 SI Repetition : Event ID = 3032 TDT max section RI : Event ID = 395a NIT Actual Min Section Reptn Int : Event ID = 3703 Ind NIT actual min section RI : Event ID = 3729 MTM400 MPEG Transport Stream Monitor Technical Reference 2−6...
  • Page 49 SDT Actual Min Any Section Reptn Int : Event ID = 3956 SDT Actual Timer : Event ID = 3952 3.5b SDT Other : Event ID = 370e Ind SDT other max section RI : Event ID = 3732 MTM400 MPEG Transport Stream Monitor Technical Reference 2−7...
  • Page 50 PID Test : PCR Overall Jitter (PCR_OJ) : Event ID = 3043 PCR Frequency Offset (PCR_FO) : Event ID = 3041 PID Test : PCR Frequency Offset (PCR_FO) : Event ID = 3044 MTM400 MPEG Transport Stream Monitor Technical Reference 2−8...
  • Page 51 DPI/SIT Any information events : Event ID = c01d DPI/SIT Data : Event ID = c017 DPI/SIT Splice Cancel : Event ID = c018 DPI/SIT Splice : Event ID = c019 DPI/SIT Program Splice : Event ID = c01a MTM400 MPEG Transport Stream Monitor Technical Reference 2−9...
  • Page 52 SFN CRC : Event ID = 3413 SFN MIP Coding : Event ID = 3414 SFN Periodicity Consistency : Event ID = 3415 SFN Pointer Consistency : Event ID = 3416 SFN (Timer) : Event ID = 3404 MTM400 MPEG Transport Stream Monitor Technical Reference 2−10...
  • Page 53: Atsc Tests

    Ind VCT max subtable RI : Event ID = 374b A/65 MGT (Timer) : Event ID = 3211 A/65 STT (Timer) : Event ID = 3212 A/65 RRT (Timer) : Event ID = 3213 A/65 MGT : Event ID = 3201 MTM400 MPEG Transport Stream Monitor Technical Reference 2−11...
  • Page 54 RF Test : IF Error Collection : Event ID = 3816 RF Test : IF Lock : Event ID = 3800 : Metric ID = 1 RF Test : MER : Event ID = d001 : Metric ID = 2 MTM400 MPEG Transport Stream Monitor Technical Reference 2−12...
  • Page 55 Template TransportStreamId error : Event ID = 6010 Template NetworkId error : Event ID = 6020 Template OriginalNetworkId error : Event ID = 6030 Template ServiceNumber error : Event ID = 6040 MTM400 MPEG Transport Stream Monitor Technical Reference 2−13...
  • Page 56: Isdb-S Tests

    NIT Actual Timer : Event ID = 3951 3.1.b NIT Other : Event ID = 3708 Ind NIT other max section RI : Event ID = 372d 3.2 SI Repetition : Event ID = 3032 MTM400 MPEG Transport Stream Monitor Technical Reference 2−14...
  • Page 57 3.5.b SDT Other : Event ID = 370e Ind SDT other max section RI : Event ID = 3732 3.6.b EIT Other : Event ID = 3144 EIT Other P Max Sect Reptn Int : Event ID = 3715 MTM400 MPEG Transport Stream Monitor Technical Reference 2−15...
  • Page 58 Progran occupancy error : Event ID = 3039 ProgramTest : Prog Occupancy : Event ID = 3039 PCR Overall Jitter (PCR_OJ) : Event ID = 3040 PID Test : PCR Overall Jitter (PCR_OJ) : Event ID = 3043 MTM400 MPEG Transport Stream Monitor Technical Reference 2−16...
  • Page 59 RF Test : Out of Order Packet : Event ID = d00e : Metric ID = 15 RF Test : Out of Order Packet Limit Error : Event ID=3856 : Metric ID=15 MTM400 MPEG Transport Stream Monitor Technical Reference 2−17...
  • Page 60: Isdb-T Tests

    Ind ISDBT NIT/EIT Consistency : Event ID = 37ab Ind ISDBT NIT/EIT Consistency : Event ID = 37ab ISDBT NIT/SDT Consistency : Event ID = 37b1 ISDBT Any IIP CRC : Event ID = 37b4 MTM400 MPEG Transport Stream Monitor Technical Reference 2−18...
  • Page 61 Event ID = 37e2 Ind H-EIT basic schedule max subtable RI for audio Cycle Group Base : Event ID = 37e3 H-EIT extended schedule max subtable RI for data : Event ID = 37ba MTM400 MPEG Transport Stream Monitor Technical Reference 2−19...
  • Page 62 SDT Max Subtable Reptn Int : Event ID = 370a Ind SDT actual max subtable RI : Event ID = 372f TOT Min Sect Reptn Int : Event ID = 371e Ind TOT min section RI : Event ID = 373d MTM400 MPEG Transport Stream Monitor Technical Reference 2−20...
  • Page 63 TOT (Table ID) : Event ID = 3119 H-EIT (Table ID) : Event ID = 311a M-EIT (Table ID) : Event ID = 311b L-EIT (Table ID) : Event ID = 311c MTM400 MPEG Transport Stream Monitor Technical Reference 2−21...
  • Page 64 DSM-CC error : Event ID = 3910 DII min RI : Event ID = 3908 Ind DII min repetition error : Event ID = 3909 DII max RI : Event ID = 390c MTM400 MPEG Transport Stream Monitor Technical Reference 2−22...
  • Page 65 RF Test : SNR Limit : Event ID = 3810 : Metric ID = 8 RF Test : SNR Drift Limit : Event ID = 3811 : Metric ID = 8 RF Test : CNR : Event ID = d009 : Metric ID = 9 MTM400 MPEG Transport Stream Monitor Technical Reference 2−23...
  • Page 66 Template StreamType error : Event ID = 6230 Template Pid constraint error : Event ID = 6240 Any Template Rating Error : Event ID = 6300 Template DVB/ATSC Ratings error : Event ID = 6301 MTM400 MPEG Transport Stream Monitor Technical Reference 2−24...
  • Page 67: Isdb (Partial Reception)

    H-EIT extended schedule max subtable RI for TV : Event ID = 37b8 Ind H-EIT basic schedule max subtable RI for TV Cycle Group 1 : Event ID = 37dc Ind H-EIT basic schedule max subtable RI for TV Cycle Group 2 : MTM400 MPEG Transport Stream Monitor Technical Reference 2−25...
  • Page 68 2.6 CAT (Table ID) : Event ID = 3107 2.6 CAT (Scrambling) : Event ID = 3114 Priority 3 : Event ID = 37f5 3.1.a NIT : Event ID = 3140 3.1 NIT (Table ID) : Event ID = 3109 MTM400 MPEG Transport Stream Monitor Technical Reference 2−26...
  • Page 69 NIT Syntax : Event ID = 3503 SDT Syntax : Event ID = 3505 EIT Syntax : Event ID = 3506 TOT Syntax : Event ID = 3508 BIT Syntax : Event ID = 3792 MTM400 MPEG Transport Stream Monitor Technical Reference 2−27...
  • Page 70 SIT (Table ID) : Event ID = 311f DIT : Event ID = 312c DIT (Table ID) : Event ID = 3126 CDT : Event ID = 3777 CDT Min Sect Reptn Int : Event ID = 3775 MTM400 MPEG Transport Stream Monitor Technical Reference 2−28...
  • Page 71 RF Test : BER (Pre Reed Solomon) : Event ID = d003 : Metric ID = 4 RF Test : BER (Pre Reed Solomon) Rate : Event ID = 3805 : Metric ID = 4 MTM400 MPEG Transport Stream Monitor Technical Reference 2−29...
  • Page 72 Any Template PID Error : Event ID = 6200 Template CADescriptorPresent error : Event ID = 6210 Template Pid scrambling error : Event ID = 6220 Template StreamType error : Event ID = 6230 MTM400 MPEG Transport Stream Monitor Technical Reference 2−30...
  • Page 73: Dcii Tests

    PNM Syntax Error : Event ID = 3514 NIM Syntax Error : Event ID = 3515 NTM Syntax Error : Event ID = 3516 VCM Syntax Error : Event ID = 3517 MTM400 MPEG Transport Stream Monitor Technical Reference 2−31...
  • Page 74 RF Test : SNR Limit : Event ID = 3810 : Metric ID = 8 RF Test : SNR Drift Limit : Event ID = 3811 : Metric ID = 8 RF Test : CNR : Event ID = d009 : Metric ID = 9 MTM400 MPEG Transport Stream Monitor Technical Reference 2−32...
  • Page 75 Template StreamType error : Event ID = 6230 Template Pid constraint error : Event ID = 6240 Any Template Rating Error : Event ID = 6300 Template DVB/ATSC Ratings error : Event ID = 6301 MTM400 MPEG Transport Stream Monitor Technical Reference 2−33...
  • Page 76: China Tests

    Ind SDT actual min section RI : Event ID = 372e SDT Actual Max Section Reptn Int : Event ID = 370b SDT Actual Max Subtable Reptn Int : Event ID = 370a MTM400 MPEG Transport Stream Monitor Technical Reference 2−34...
  • Page 77 EIT Other P Max Sect Reptn Int : Event ID = 3715 EIT Other F Max Sect Reptn Int : Event ID = 3716 3.6.c EIT PF : Event ID = 3333 Ind DVB EIT P/F presence consistency : Event ID = 3051 MTM400 MPEG Transport Stream Monitor Technical Reference 2−35...
  • Page 78 Excess (>8) DPI/SIT PIDs per Program : Event ID = 3824 DPI/SIT Encrypted Error : Event ID = 3825 DPI/SIT Missing : Event ID = 3826 Ind DPI/SIT Missing : Event ID = 3827 DPI/SIT Syntax : Event ID = 3828 MTM400 MPEG Transport Stream Monitor Technical Reference 2−36...
  • Page 79 PID Test : Discontinuity : Event ID = 3133 Transport Stream Occupancy : Event ID = 3600 Service Log Overflow : Event ID = 5200 Program Information : Event ID = c001 MTM400 MPEG Transport Stream Monitor Technical Reference 2−37...
  • Page 80: Info Tests

    Polling Channel Change Completed : Event ID = C02D Polling Stopped : Event ID = C02B Any DPI/SIT information : Event ID = C01D DPI/SIT Data : Event ID = C017 DPI/SIT Splice Cancel : Event ID = C018 MTM400 MPEG Transport Stream Monitor Technical Reference 2−38...
  • Page 81 RTP Lost Rate Warning : Event ID = C022 Packet interarrival time Warning : Event ID = C024 RTP Out Of Order Rate Warning : Event ID = C026 ISDBT IIP Partial Reception Flag Set : Event ID = C01F MTM400 MPEG Transport Stream Monitor Technical Reference 2−39...
  • Page 82 Test Parameters - Standards Tests MTM400 MPEG Transport Stream Monitor Technical Reference 2−40...
  • Page 83: Event Identity To Test Name

    MPEG, DVB, ATSC, ISDB, Chinese, DCII 4101 (Hex: 0x1005) EVID_DCVOLTAGE test change Description: EVID_DCVOLTAGE Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII 4128 (Hex: 0x1020) EVID_PLUS_FIVE_VOLTS Description: EVID_PLUS_FIVE_VOLTS Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII MTM400 MPEG Transport Stream Monitor Technical Reference 2−41...
  • Page 84 The current state of fan 2 Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII 4162 (Hex: 0x1042) Fan 3 Description: The current state of fan 3 Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII MTM400 MPEG Transport Stream Monitor Technical Reference 2−42...
  • Page 85 MPEG, DVB, ATSC, ISDB, Chinese, DCII 4357 (Hex: 0x1105) EVID_CLEAR_LOG Description: EVID_CLEAR_LOG Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII 4608 (Hex: 0x1200) EVID_SV_DEBUG Description: EVID_SV_DEBUG Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII MTM400 MPEG Transport Stream Monitor Technical Reference 2−43...
  • Page 86 MPEG, DVB, ATSC, ISDB, Chinese, DCII 4616 (Hex: 0x1208) EVID_NETWORK Description: EVID_NETWORK Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII 4617 (Hex: 0x1209) EVID_LOGIC Description: EVID_LOGIC Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII MTM400 MPEG Transport Stream Monitor Technical Reference 2−44...
  • Page 87 MPEG, DVB, ATSC, ISDB, Chinese, DCII 4630 (Hex: 0x1216) System Card Description: System Card state Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII 4631 (Hex: 0x1217) EVID_BOX_TIME_SET Description: EVID_BOX_TIME_SET Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII MTM400 MPEG Transport Stream Monitor Technical Reference 2−45...
  • Page 88 Program Occupancy Description: Program occupancy exceeds limits Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII 8195 (Hex: 0x2003) EVID_PIDGROUP_OCC_LIM Description: PID Group occupancy exceeds limits Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII MTM400 MPEG Transport Stream Monitor Technical Reference 2−46...
  • Page 89 Sync Byte (DVB test 1.2) Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII 12308 (Hex: 0x3014) 1.4 Continuity Description: Continuity Error (DVB test 1.4) Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII MTM400 MPEG Transport Stream Monitor Technical Reference 2−47...
  • Page 90 2.1 Transport Description: Transport (DVB test 2.1) Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII 12322 (Hex: 0x3022) 2.2 CRC Description: CRC (DVB test 2.2) Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII MTM400 MPEG Transport Stream Monitor Technical Reference 2−48...
  • Page 91 PTS arrival history length 12326 (Hex: 0x3026) 2.6 CAT Description: CAT (DVB test 2.6) Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII Associated Parameter(s) PS13 CAT present timer PS61 CAT obsolescence count MTM400 MPEG Transport Stream Monitor Technical Reference 2−49...
  • Page 92 EIT actual schedule maximum repetition interval PS35 EIT other schedule min section repetition interval PS36 EIT other schedule max repetition interval PS39 TDT min section repetition interval PS40 TDT max repetition interval PS41 TOT min repetition interval MTM400 MPEG Transport Stream Monitor Technical Reference 2−50...
  • Page 93 Associated Parameter(s) PS39 TDT min section repetition interval PS40 TDT max repetition interval 12345 (Hex: 0x3039) Prog Occupancy Description: Indicates Program occupancy exceeds limits Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII MTM400 MPEG Transport Stream Monitor Technical Reference 2−51...
  • Page 94 PSK Maximum PCR overall jitter PP41 QAM Max PCR overall jitter PP51 COFDM Max PCR overall jitter PP61 IP Max PCR overall jitter PS181 PCR_OJ/AC high-pass filter cutoff (0 for same as DR/FO filter cutoff) MTM400 MPEG Transport Stream Monitor Technical Reference 2−52...
  • Page 95 QAM Maximum PCR frequency drift rate PP53 COFDM Maximum PCR frequency drift rate PP63 IP Maximum PCR frequency drift rate PS174 PCR_FO/DR low-pass filter cutoff frequency PS178 PCR trend graph sample period MTM400 MPEG Transport Stream Monitor Technical Reference 2−53...
  • Page 96 VSB Maximum PCR frequency drift rate PP33 PSK Maximum PCR frequency drift rate PP43 QAM Maximum PCR frequency drift rate PP53 COFDM Maximum PCR frequency drift rate PP63 IP Maximum PCR frequency drift rate MTM400 MPEG Transport Stream Monitor Technical Reference 2−54...
  • Page 97 1.3 PAT (Scrambling) Description: PAT Error Scrambling Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII 12547 (Hex: 0x3103) 1.5 PMT (Timer) Description: PAT Error Timer Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII MTM400 MPEG Transport Stream Monitor Technical Reference 2−55...
  • Page 98 CAT Scrambling Description: CAT Error Scrambling Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII 12565 (Hex: 0x3115) CAT max subtable RI Description: PCR Error Timer Applicable Standards: MPEG, DVB, ISDB, Chinese, DCII MTM400 MPEG Transport Stream Monitor Technical Reference 2−56...
  • Page 99 M-EIT Err Table Id Applicable Standards: ISDB 12572 (Hex: 0x311C) L-EIT (Table ID) Description: L-EIT Err Table Id Applicable Standards: ISDB 12573 (Hex: 0x311D) L-SDTT (Table ID) Description: SDTT(L) Err Table Id Applicable Standards: ISDB MTM400 MPEG Transport Stream Monitor Technical Reference 2−57...
  • Page 100 EIT actual PF obsolescence count 12584 (Hex: 0x3128) M-EIT Description: Collection event for all M-EIT errors Applicable Standards: ISDB Associated Parameter(s) PS113 M-EIT maximum repetition interval PS115 M-EIT minimum section repetition interval PS51 EIT obsolescence count MTM400 MPEG Transport Stream Monitor Technical Reference 2−58...
  • Page 101 ISDB 12593 (Hex: 0x3131) Discontinuity Description: The discontinuity_indicator must not be set to ’1’ in three consecutive transport stream packets of that same PID. Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII MTM400 MPEG Transport Stream Monitor Technical Reference 2−59...
  • Page 102 = 0x42 (SDT_actual) occur on PID 0x0011 within a specified value (25ms or lower). Applicable Standards: DVB, ISDB, Chinese Associated Parameter(s) PS20 SDT actual minimum section repetition interval PS21 SDT actual maximum repetition interval PS22 SDT actual obsolescence count MTM400 MPEG Transport Stream Monitor Technical Reference 2−60...
  • Page 103 EIT other schedule obsolescence count 12624 (Hex: 0x3150) 2.3a PCR Repetition Description: PCR Error Timer Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII Associated Parameter(s) PP17 Partial Reception PCR max repetition interval PCR max repetition interval MTM400 MPEG Transport Stream Monitor Technical Reference 2−61...
  • Page 104 Associated Parameter(s) PS46 STT max section repetition interval 12803 (Hex: 0x3203) A/65 RRT Description: A/65 RRT Error Applicable Standards: ATSC Associated Parameter(s) PS49 RRT max section repetition interval PS66 RRT obsolescence count MTM400 MPEG Transport Stream Monitor Technical Reference 2−62...
  • Page 105 VCT Timer Error Applicable Standards: ATSC 12817 (Hex: 0x3211) A/65 MGT (Timer) Description: MGT Timer Error Applicable Standards: ATSC 12818 (Hex: 0x3212) A/65 STT (Timer) Description: STT Timer Error Applicable Standards: ATSC MTM400 MPEG Transport Stream Monitor Technical Reference 2−63...
  • Page 106 13107 (Hex: 0x3333) 3.6c EIT PF Description: If either section (’0’ or ’1’) of each EIT P/F subtable is present both must exist. Otherwise EIT_PF_error should be indicated. Applicable Standards: DVB, ISDB, Chinese MTM400 MPEG Transport Stream Monitor Technical Reference 2−64...
  • Page 107 SFN MIP Length Description: SFN MIP decode syntax check - length error Applicable Standards: DVB, Chinese 13331 (Hex: 0x3413) SFN CRC Description: SFN MIP decode syntax check - crc error Applicable Standards: DVB, Chinese MTM400 MPEG Transport Stream Monitor Technical Reference 2−65...
  • Page 108 13572 (Hex: 0x3504) BAT Syntax Description: Syntax error in BAT table Applicable Standards: DVB, Chinese 13573 (Hex: 0x3505) SDT Syntax Description: Syntax error in any SDT table Applicable Standards: DVB, ISDB, Chinese MTM400 MPEG Transport Stream Monitor Technical Reference 2−66...
  • Page 109 Applicable Standards: ATSC 13581 (Hex: 0x350D) EIT-k Syntax Description: Syntax error in ATSC EIT table Applicable Standards: ATSC 13582 (Hex: 0x350E) STT Syntax Description: Syntax error in STT table Applicable Standards: ATSC MTM400 MPEG Transport Stream Monitor Technical Reference 2−67...
  • Page 110 Syntax error in NTM message Applicable Standards: DCII 13591 (Hex: 0x3517) VCM Syntax Description: Syntax error in VCM message Applicable Standards: DCII 13592 (Hex: 0x3518) STM Syntax Description: Syntax error in STM message Applicable Standards: DCII MTM400 MPEG Transport Stream Monitor Technical Reference 2−68...
  • Page 111 Depending on the severity of the error, faults may be tolerated or result in the section being discarded. Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII Associated Parameter(s) MTM400 MPEG Transport Stream Monitor Technical Reference 2−69...
  • Page 112 = 0x41 (NIT_other) on PID 0x0010 longer than a specified value (10s or higher). Applicable Standards: DVB, ISDB, Chinese Associated Parameter(s) PS17 NIT other network min section repetition interval PS18 NIT other network max repetition interval PS19 NIT other network obsolescence count MTM400 MPEG Transport Stream Monitor Technical Reference 2−70...
  • Page 113 SDT other max repetition interval PS25 SDT other obsolescence count 14095 (Hex: 0x370F) EIT Actual PF Min Sect Reptn Int Description: DVB EIT actual_transport_stream present/following minimum section repetition interval. Applicable Standards: DVB, ISDB, Chinese MTM400 MPEG Transport Stream Monitor Technical Reference 2−71...
  • Page 114 DVB EIT other_transport_stream present maximum section repetition interval Applicable Standards: DVB, ISDB, Chinese 14102 (Hex: 0x3716) EIT Other F Max Sect Reptn Int Description: DVB EIT other_transport_stream following maximum section repetition interval Applicable Standards: DVB, ISDB, Chinese MTM400 MPEG Transport Stream Monitor Technical Reference 2−72...
  • Page 115 TOT Min Sect Reptn Int Description: TOT minimum section repetition interval Applicable Standards: DVB, ISDB, Chinese 14111 (Hex: 0x371F) TOT Max Sect Reptn Int Description: TOT maximum repetition interval Applicable Standards: DVB, ISDB, Chinese MTM400 MPEG Transport Stream Monitor Technical Reference 2−73...
  • Page 116 AL_MAX_SUBTABLE_RI Description: Ind NIT actual_network maximum subtable repetition interval Applicable Standards: DVB, ISDB, Chinese 14123 (Hex: 0x372B) EVID_INDIVIDUAL_NIT_OTH - ER_MIN_SECTION_RI Description: Ind NIT other_network minimum section repetition interval Applicable Standards: DVB, Chinese MTM400 MPEG Transport Stream Monitor Technical Reference 2−74...
  • Page 117 Description: Ind SDT other_transport_stream maximum subtable repetition interval Applicable Standards: DVB, ISDB, Chinese 14130 (Hex: 0x3732) EVID_INDIVIDUAL_SDT_OTH - ER_MAX_SECTION_RI Description: Ind SDT other_transport_stream maximum section repetition interval Applicable Standards: DVB, ISDB, Chinese MTM400 MPEG Transport Stream Monitor Technical Reference 2−75...
  • Page 118 Ind DVB EIT actual_transport_stream schedule maximum subtable repetition interval Applicable Standards: DVB, ISDB, Chinese 14137 (Hex: 0x3739) EVID_INDIVIDUAL_DVBEIT_OTH - ER_S_MIN_SECTION Description: Ind DVB EIT other_transport_stream schedule minimum section repetition interval Applicable Standards: DVB, ISDB, Chinese MTM400 MPEG Transport Stream Monitor Technical Reference 2−76...
  • Page 119 DVB, Chinese 14143 (Hex: 0x373F) EVID_INDIVID- UAL_BAT_MAX_SUBTABLE_RI Description: Ind BAT maximum subtable repetition interval Applicable Standards: DVB, Chinese 14145 (Hex: 0x3741) EVID_INDIVID- UAL_SDTT_MIN_SECTION_RI Description: Ind SDTT minimum section repetition interval Applicable Standards: ISDB MTM400 MPEG Transport Stream Monitor Technical Reference 2−77...
  • Page 120 Applicable Standards: ISDB 14158 (Hex: 0x374E) EVID_INDIVID- UAL_CDT_MIN_SECTION_RI Description: Ind CDT minimum section repetition interval Applicable Standards: ISDB 14161 (Hex: 0x3751) NIT Actual Missing Description: NIT Table not detected Applicable Standards: DVB, Chinese MTM400 MPEG Transport Stream Monitor Technical Reference 2−78...
  • Page 121: Description: Applicable Standards

    EIT-0,1,2,3 Missing Description: ATSC EIT 0, 1, 2, 3 tables not detected Applicable Standards: ATSC 14172 (Hex: 0x375C) M-EIT Max Subtable Reptn Int Description: M-EIT Maximum Subtable repetition interval Applicable Standards: ISDB MTM400 MPEG Transport Stream Monitor Technical Reference 2−79...
  • Page 122: Description: Applicable Standards

    ISDB 14192 (Hex: 0x3770) SDTT Description: Collection event for all SDTT errors Applicable Standards: ISDB Associated Parameter(s) PS70 SDTT obsolescence count PS71 SDTT max repetition interval PS86 SDTT min section repetition interval MTM400 MPEG Transport Stream Monitor Technical Reference 2−80...
  • Page 123 SDTT Err Table Id Applicable Standards: ISDB 14209 (Hex: 0x3781) BIT (Table ID) Description: BIT Err Table Id Applicable Standards: ISDB 14225 (Hex: 0x3791) SDTT Syntax Description: Syntax error in SDTT table Applicable Standards: ISDB MTM400 MPEG Transport Stream Monitor Technical Reference 2−81...
  • Page 124 ISDB 14238 (Hex: 0x379E) ISDBT Mode/Guard Interval Valida- tion Description: ISDBT Mode/Guard Interval Validation Applicable Standards: ISDB 14239 (Hex: 0x379F) ISDBT Time Interleaving Validation Description: ISDBT Time Interleaving Validation Applicable Standards: ISDB MTM400 MPEG Transport Stream Monitor Technical Reference 2−82...
  • Page 125 14247 (Hex: 0x37A7) ISDBT SDT/EIT Consistency Description: ISDBT SDT/EIT Consistency Applicable Standards: ISDB Associated Parameter(s) PS111 SDT/EIT Consistency Timer Interval 14248 (Hex: 0x37A8) EVID_ISDBT_INDIVID - UAL_SDT_EIT_CONSISTENCY Description: Ind ISDBT SDT/EIT Consistency Applicable Standards: ISDB MTM400 MPEG Transport Stream Monitor Technical Reference 2−83...
  • Page 126 14259 (Hex: 0x37B3) ISDBT IIP SFN Sync CRC Description: ISDBT IIP SFN Sync CRC Applicable Standards: ISDB 14260 (Hex: 0x37B4) ISDBT Any IIP CRC Description: ISDBT Any IIP CRC Applicable Standards: ISDB MTM400 MPEG Transport Stream Monitor Technical Reference 2−84...
  • Page 127 EIT basic schedule (Data) number of segments in cycle group 1 PS124 EIT basic schedule (Data) number of segments in cycle group 2 PS125 EIT basic schedule (Data) number of segments in cycle group 3 MTM400 MPEG Transport Stream Monitor Technical Reference 2−85...
  • Page 128 EIT extended schedule (Sound) max cycle group 1 repetition interval PS153 EIT extended schedule (Sound) max cycle group 2 repetition interval PS154 EIT extended schedule (Sound) max cycle group 3 repetition interval PS164 EIT extended schedule (Sound) range MTM400 MPEG Transport Stream Monitor Technical Reference 2−86...
  • Page 129 ISDBT TMCC Id Error Applicable Standards: ISDB 14276 (Hex: 0x37C4) ISDBT Max Partial Reception Services Error Description: ISDBT Maximum Partial Reception Services Error Applicable Standards: ISDB Associated Parameter(s) PS264 Maximum number of partial reception services MTM400 MPEG Transport Stream Monitor Technical Reference 2−87...
  • Page 130 Cycle Group Base Applicable Standards: ISDB 14292 (Hex: 0x37D4) EVID_INDIVIDUAL_HEIT_BA - SIC_SCD_AUDIO_MAX_R Description: Ind H-EIT basic schedule maximum subtable repetition interval for audio services Cycle Group 1 Applicable Standards: ISDB MTM400 MPEG Transport Stream Monitor Technical Reference 2−88...
  • Page 131 Ind H-EIT basic schedule maximum subtable repetition interval for data services Cycle Group 3 Applicable Standards: ISDB 14299 (Hex: 0x37DB) EVID_INDIVIDUAL_HEIT_BA - SIC_SCD_DATA_MAX_RI Description: Ind H-EIT basic schedule maximum subtable repetition interval for data services Cycle Group Base Applicable Standards: ISDB MTM400 MPEG Transport Stream Monitor Technical Reference 2−89...
  • Page 132 Cycle Group 1 Applicable Standards: ISDB 14305 (Hex: 0x37E1) EVID_INDIVID- UAL_HEIT_EXT_SCD_AU- DIO_MAX_RI_ Description: Ind H-EIT basic schedule maximum subtable repetition interval for audio services Cycle Group 2 Applicable Standards: ISDB MTM400 MPEG Transport Stream Monitor Technical Reference 2−90...
  • Page 133 Ind H-EIT basic schedule maximum subtable repetition interval for data services Cycle Group 3 Applicable Standards: ISDB 14311 (Hex: 0x37E7) EVID_INDIVID- UAL_HEIT_EXT_SCD_DATA_MAX_ RI_B Description: Ind H-EIT basic schedule maximum subtable repetition interval for data services Cycle Group Base Applicable Standards: ISDB MTM400 MPEG Transport Stream Monitor Technical Reference 2−91...
  • Page 134: Ind Sdtt Maximum Subtable Repetition Interval

    Associated Parameter(s) 14318 (Hex: 0x37EE) EVID_INDIVID- UAL_LSDTT_MIN_SECTION_RI Description: Ind SDTT(L) minimum section repetition interval Applicable Standards: ISDB 14319 (Hex: 0x37EF) EVID_INDIVID- UAL_LSDTT_MAX_SUBTABLE_RI Description: Ind SDTT(L) maximum subtable repetition interval Applicable Standards: ISDB MTM400 MPEG Transport Stream Monitor Technical Reference 2−92...
  • Page 135 MPEG, DVB, ATSC, ISDB, Chinese, DCII 14327 (Hex: 0x37F7) TR 101 290 Description: TR 101 290 Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII 14328 (Hex: 0x37F8) ISDB Tests Description: ISDB Tests Applicable Standards: ISDB MTM400 MPEG Transport Stream Monitor Technical Reference 2−93...
  • Page 136 MPEG, DVB, ATSC, ISDB, Chinese, DCII Associated Parameter(s) PS201 MER absolute limit 14338 (Hex: 0x3802) EVID_RF_MER_DRIFT Description: RF MER drift limit error Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII Associated Parameter(s) PS202 MER drift limit MTM400 MPEG Transport Stream Monitor Technical Reference 2−94...
  • Page 137 BER PRE Viterbi abs Limit 14344 (Hex: 0x3808) EVID_RF_BER_PRE_VITER - BI_DRIFT Description: RF pre Viterbi drift limit error Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII Associated Parameter(s) PS208 BER pre viterbi drift limit MTM400 MPEG Transport Stream Monitor Technical Reference 2−95...
  • Page 138 MPEG, DVB, ATSC, ISDB, Chinese, DCII Associated Parameter(s) PS213 Power high limit 14350 (Hex: 0x380E) EVID_RF_POWER_LOW Description: RF Low Power limit error Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII Associated Parameter(s) PS214 Power low limit MTM400 MPEG Transport Stream Monitor Technical Reference 2−96...
  • Page 139 MPEG, DVB, ATSC, ISDB, Chinese, DCII Associated Parameter(s) PS219 CNR drift 14356 (Hex: 0x3814) EVID_RF_CARRIER_OFFSET Description: RF Carrier offset limit error Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII Associated Parameter(s) PS220 Carrier offset limit MTM400 MPEG Transport Stream Monitor Technical Reference 2−97...
  • Page 140 Signalled DPI information has not arrived Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII 14376 (Hex: 0x3828) DPI/SIT Syntax error Description: DPI table syntax error Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII MTM400 MPEG Transport Stream Monitor Technical Reference 2−98...
  • Page 141 Packet interval timing limit 14422 (Hex: 0x3856) RF Out of order packet limit error Description: RF Out-of-order packet limit error Applicable Standards: Associated Parameter(s) PS277 Out of order packets per second limit MTM400 MPEG Transport Stream Monitor Technical Reference 2−99...
  • Page 142 Description: DII minimum repetition interval Applicable Standards: ISDB Associated Parameter(s) PS184 DII min repetition interval 14601 (Hex: 0x3909) Ind DII min repetition error Description: Ind DII minimum repetition error Applicable Standards: ISDB MTM400 MPEG Transport Stream Monitor Technical Reference 2−100...
  • Page 143: Dvb, Chinese

    MPEG, DVB, ISDB, Chinese, DCII 14673 (Hex: 0x3951) NIT Actual Timer Description: NIT Actual Timer Applicable Standards: DVB, ISDB, Chinese 14674 (Hex: 0x3952) SDT Actual Timer Description: SDT Actual Timer Applicable Standards: DVB, ISDB, Chinese MTM400 MPEG Transport Stream Monitor Technical Reference 2−101...
  • Page 144 RST Min Any Sect Reptn Int Description: RST minimum any section repetition interval Applicable Standards: DVB, Chinese 14682 (Hex: 0x395A) TDT max section RI Description: TDT maximum section repetition interval Applicable Standards: DVB, Chinese MTM400 MPEG Transport Stream Monitor Technical Reference 2−102...
  • Page 145 Service Information Strained Description: In the MTM400, received tables are held in a fixed-sized database. This is large enough for the majority of streams, but if the stream contains too much SI, some of the SI will be discarded and this test will indicate an error.
  • Page 146 Template Error with Service Name Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII 24896 (Hex: 0x6140) Template Service Constraint Err Description: Template Error with Service Constraint Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII MTM400 MPEG Transport Stream Monitor Technical Reference 2−104...
  • Page 147 PLATE_RATING_ERR Description: Template DVB/ATSC Ratings error Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII 28671 (Hex: 0x6FFF) Template Master Error Description: Any Template Error Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII MTM400 MPEG Transport Stream Monitor Technical Reference 2−105...
  • Page 148 MPEG Continuity Count Error Description: TS Continuity Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII 37122 (Hex: 0x9102) MPEG Sync Byte Error Description: TS Sync Byte Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII MTM400 MPEG Transport Stream Monitor Technical Reference 2−106...
  • Page 149 Associated Parameter(s) PS223 MER drift warning limit 49156 (Hex: 0xC004) RF_EVM_W Description: RF EVM limit warning (information only) Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII Associated Parameter(s) PS224 EVM warning limit MTM400 MPEG Transport Stream Monitor Technical Reference 2−107...
  • Page 150 BER PRE viterbi drift warning limit 49162 (Hex: 0xC00A) RF_BER_POST_RS_W Description: RF post RS BER limit warning (information only) Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII Associated Parameter(s) PS230 BER POST RS warning limit MTM400 MPEG Transport Stream Monitor Technical Reference 2−108...
  • Page 151 PS235 Power low warning limit 49168 (Hex: 0xC010) RF_POWER_DRIFT_W Description: RF Power drift limit warning (information only) Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII Associated Parameter(s) PS236 power drift warning limit MTM400 MPEG Transport Stream Monitor Technical Reference 2−109...
  • Page 152 Carrier offset warning limit 49174 (Hex: 0xC016) RF_CARRIER_OFFSET_DRIFT_W Description: RF Carrier offset drift limit warning (information only) Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII Associated Parameter(s) PS242 Carrier offset drift warning limit MTM400 MPEG Transport Stream Monitor Technical Reference 2−110...
  • Page 153 Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII 49183 (Hex: 0xC01F) ISDBT IIP Partial Reception Flag Set Description: ISDBT IIP Partial Reception Flag Set Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII MTM400 MPEG Transport Stream Monitor Technical Reference 2−111...
  • Page 154 49195 (Hex: 0xC02B) Polling Stopped Description: Polling Stopped Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII 49196 (Hex: 0xC02C) Polling Channel Change Soon Description: Channel Polling Event Due Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII MTM400 MPEG Transport Stream Monitor Technical Reference 2−112...
  • Page 155 53253 (Hex: 0xD005) BER (Post Reed Solomon) Description: BER (Post Reed Solomon) Applicable Standards: 53255 (Hex: 0xD007) Power Description: Power Applicable Standards: 53256 (Hex: 0xD008) Description: Applicable Standards: 53257 (Hex: 0xD009) Description: Applicable Standards: MTM400 MPEG Transport Stream Monitor Technical Reference 2−113...
  • Page 156 Description: BER (Pre Reed Solomon) Warning Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII 53508 (Hex: 0xD104) BER (Pre-Viterbi) Warning Description: BER (Pre-Viterbi) Warning Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII MTM400 MPEG Transport Stream Monitor Technical Reference 2−114...
  • Page 157 53513 (Hex: 0xD109) CNR Warning Description: CNR Warning Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII 53514 (Hex: 0xD10A) Carrier Offset Warning Description: Carrier Offset Warning Applicable Standards: MPEG, DVB, ATSC, ISDB, Chinese, DCII MTM400 MPEG Transport Stream Monitor Technical Reference 2−115...
  • Page 158 Test Parameters - Event Identity to Test Name MTM400 MPEG Transport Stream Monitor Technical Reference 2−116...
  • Page 159: Test Name To Event Identity

    2.3b PCR Discontinuity Indicator 12568 0x3118 2.3b PCR Discontinuity Indicator 12625 0x3151 2.4 PCR Accuracy 12328 0x3028 2.4 PCR Accuracy 12324 0x3024 2.5 PTS 14120 0x3728 2.5 PTS 12325 0x3025 2.6 CAT 12326 0x3026 MTM400 MPEG Transport Stream Monitor Technical Reference 2−117...
  • Page 160 12816 0x3210 A53 non−AC3 Audio 14432 0x3860 Any Box Error 4096 0x1000 Any DPI/SIT Errors 14378 0x382A Any DPI/SIT Information 49180 0xC01C Any Program Error 8200 0x2008 Any Stream Error 8192 0x2000 MTM400 MPEG Transport Stream Monitor Technical Reference 2−118...
  • Page 161 CDT Syntax 14233 0x3799 53257 0xD009 CNR Warning 53513 0xD109 Corrupt Packet 53259 0xD00B DCCSCT Syntax 13585 0x3511 DCCT Syntax 13584 0x3510 DII download completion 14606 0x390E DII max RI 14604 0x390C MTM400 MPEG Transport Stream Monitor Technical Reference 2−119...
  • Page 162 EIT Actual PF Min Any Section Reptn Int 14679 0x3957 EIT Actual PF Min Sect Reptn Int 14095 0x370F EIT Actual PF Missing 14163 0x3753 EIT Actual Sched Max Subtable Reptn Int 14104 0x3718 MTM400 MPEG Transport Stream Monitor Technical Reference 2−120...
  • Page 163 EVID_CDT_ERR_TABLE_ID 14211 0x3783 EVID_CLEAR_LOG 4357 0x1105 EVID_CONTINUITY_COUNT_ERROR 12592 0x3130 EVID_DCVOLTAGE test change 4101 0x1005 EVID_EVENT_RESET 4356 0x1104 EVID_FIRMWARE_UPLOAD 4615 0x1207 EVID_FLOPPY_DISK 4099 0x1003 EVID_FRONT_PANEL_ITEM 4629 0x1215 EVID_GLOBAL_MMODE 20481 0x5001 EVID_HARD_DISK 4098 0x1002 MTM400 MPEG Transport Stream Monitor Technical Reference 2−121...
  • Page 164 EVID_INDIVIDUAL_HEIT_BASIC_SCD_DA TA_MAX_RI_CYC2 14297 0x37D9 EVID_INDIVIDUAL_HEIT_BASIC_SCD_DA TA_MAX_RI_CYC3 14298 0x37DA EVID_INDIVIDUAL_HEIT_BASIC_SCD_TV_MAX_RI_BASE 14291 0x37D3 EVID_INDIVIDUAL_HEIT_BASIC_SCD_TV_MAX_RI_CYC1 14288 0x37D0 EVID_INDIVIDUAL_HEIT_BASIC_SCD_TV_MAX_RI_CYC2 14289 0x37D1 EVID_INDIVIDUAL_HEIT_BASIC_SCD_TV_MAX_RI_CYC3 14290 0x37D2 EVID_INDIVIDUAL_HEIT_EXT_SCD_AUDIO_MAX_RI_BASE 14307 0x37E3 EVID_INDIVIDUAL_HEIT_EXT_SCD_AUDIO_MAX_RI_CYC1 14304 0x37E0 EVID_INDIVIDUAL_HEIT_EXT_SCD_AUDIO_MAX_RI_CYC2 14305 0x37E1 EVID_INDIVIDUAL_HEIT_EXT_SCD_AUDIO_MAX_RI_CYC3 14306 0x37E2 MTM400 MPEG Transport Stream Monitor Technical Reference 2−122...
  • Page 165 14125 0x372D EVID_INDIVIDUAL_NIT_OTHER_MAX_SUBT ABLE_RI 14124 0x372C EVID_INDIVIDUAL_NIT_OTHER_MIN_SECTION_RI 14123 0x372B EVID_INDIVIDUAL_PCR_ERR 12327 0x3027 EVID_INDIVIDUAL_RST_MIN_SECTION_RI 14139 0x373B EVID_INDIVIDUAL_SDT_ACTUAL_MAX_SUBT ABLE_RI 14127 0x372F EVID_INDIVIDUAL_SDT_ACTUAL_MIN_SECTION_RI 14126 0x372E EVID_INDIVIDUAL_SDT_OTHER_MAX_SECTION_RI 14130 0x3732 EVID_INDIVIDUAL_SDT_OTHER_MAX_SUBT ABLE_RI 14129 0x3731 EVID_INDIVIDUAL_SDT_OTHER_MIN_SECTION_RI 14128 0x3730 MTM400 MPEG Transport Stream Monitor Technical Reference 2−123...
  • Page 166 4128 0x1020 EVID_PLUS_TWELVE_VOLTS 4129 0x1021 EVID_RECORDING_COMPLETE 45312 0xB100 EVID_RF_BER_POST_RS 14345 0x3809 EVID_RF_BER_POST_RS_DRIFT 14346 0x380A EVID_RF_BER_PRE_RS 14341 0x3805 EVID_RF_BER_PRE_RS_DRIFT 14342 0x3806 EVID_RF_BER_PRE_VITERBI 14343 0x3807 EVID_RF_BER_PRE_VITERBI_DRIFT 14344 0x3808 EVID_RF_CARRIER_OFFSET 14356 0x3814 EVID_RF_CARRIER_OFFSET_DRIFT 14357 0x3815 MTM400 MPEG Transport Stream Monitor Technical Reference 2−124...
  • Page 167 14231 0x3797 EVID_SYNTAX_ITT 14232 0x3798 EVID_SYNTAX_LDT 14229 0x3795 EVID_SYNTAX_LIT 14230 0x3796 EVID_SYNTAX_NBIT 14227 0x3793 EVID_SYNTAX_NBIT_LINK_INFO 14228 0x3794 EVID_SYNTAX_PCAT 14224 0x3790 EVID_TEMPLATE_MATCH 13056 0x3300 EVID_TIME_SET 49152 0xC000 EVID_TRAPS_THROTTLED 20996 0x5204 EVID_TS_SYNC_STATE 12368 0x3050 MTM400 MPEG Transport Stream Monitor Technical Reference 2−125...
  • Page 168 H−EIT extended schedule max subtable RI for TV 14264 0x37B8 H−EIT Extended Schedule Syntax 13597 0x351D HEIT Schedule 14333 0x37FD H−EIT Syntax 13593 0x3519 H−SDTT 12586 0x312A H−SDTT (Table ID) 12574 0x311E 4609 0x1201 Ind DII completition 14607 0x390F MTM400 MPEG Transport Stream Monitor Technical Reference 2−126...
  • Page 169 ISDBT TMCC Id Error 14275 0x37C3 ISDBT Transmission Mode Consistency 14235 0x379B L−EIT 12585 0x3129 L−EIT (Table ID) 12572 0x311C L−EIT Max Subtable Reptn Int 14174 0x375E L−EIT Min Sect Reptn Int 14175 0x375F MTM400 MPEG Transport Stream Monitor Technical Reference 2−127...
  • Page 170 14161 0x3751 NIT Actual Timer 14673 0x3951 NIT Err Timer 12552 0x3108 NIT Other Max Subtable Reptn Int 14087 0x3707 NIT Other Min Section Reptn Int 14086 0x3706 NIT Syntax 13571 0x3503 MTM400 MPEG Transport Stream Monitor Technical Reference 2−128...
  • Page 171 PNM Syntax 13588 0x3514 Polling Channel Change 49194 0xC02A Polling Channel Change Completed 49197 0xC02D Polling Channel Change Soon 49196 0xC02C Polling Stopped 49195 0xC02B Power 53255 0xD007 Power Warning 53511 0xD107 MTM400 MPEG Transport Stream Monitor Technical Reference 2−129...
  • Page 172 RF Packet interval time drift limit warning 49189 0xC025 RF Packet interval time limit error 14420 0x3854 RF Packet interval time limit warning 49188 0xC024 RF_BER_POST_RS_DRIFT_W 49163 0xC00B RF_BER_POST_RS_W 49162 0xC00A RF_BER_PRE_RS_DRIFT_W 49159 0xC007 MTM400 MPEG Transport Stream Monitor Technical Reference 2−130...
  • Page 173 Script Validation Error 14592 0x3900 12341 0x3035 SDT Actual Max Section Reptn Int 14091 0x370B SDT Actual Max Subtable Reptn Int 14090 0x370A SDT Actual Min Any Section Reptn Int 14678 0x3956 MTM400 MPEG Transport Stream Monitor Technical Reference 2−131...
  • Page 174 SFN One MIP per M/F 13328 0x3410 SFN Packet Cout Err 13314 0x3402 SFN Periodicity Consistency 13333 0x3415 SFN Pointer Consistency 13334 0x3416 SFN Repetition 13329 0x3411 12589 0x312D SIT (Table ID) 12575 0x311F MTM400 MPEG Transport Stream Monitor Technical Reference 2−132...
  • Page 175 Template Rating Error 25344 0x6300 Template Rating Guidance Err 25376 0x6320 Template Rating Region Err 25360 0x6310 Template Service Constraint Err 24896 0x6140 Template Service Error 24832 0x6100 Template Service Name Err 24880 0x6130 MTM400 MPEG Transport Stream Monitor Technical Reference 2−133...
  • Page 176 Transport Stream Occupancy 13824 0x3600 TS Availability 12371 0x3053 VCM Message Missing 14388 0x3834 VCM Syntax 13591 0x3517 VCT Max Sect Reptn Int 14156 0x374C VCT Missing 14166 0x3756 VCT Syntax 13580 0x350C MTM400 MPEG Transport Stream Monitor Technical Reference 2−134...
  • Page 177: Parameter Reference

    Parameter Reference The following pages list all of the parameters that can be used in the MTM400 configuration file. Refer to Example Configuration File on page 3−6 to view an example configura- tion file. General Parameters The following parameters can be used in all streams.
  • Page 178 Test Parameters - Parameter Reference <TimeSource> </TimeSource> Description Set time source Real Time Clock: The MTM400 internal clock. LTC (Longitudinal Time Clock): An analog format time clock often available from a centralized source. SNTP (Simple Network Time Protocol): A UTC-synchronized time clock available over the internet.
  • Page 179 <Satellite></Satellite> Description Non-DVB standard specialization <MTM400Configuration> → <Streams> → <Stream> → <Satellite> Path Data Value Type: Numeral Values: 0 = Satellite 1 = Terrestrail 2 = Cable 3 = ISDB-T (Partial Reception) MTM400 MPEG Transport Stream Monitor Technical Reference 2−137...
  • Page 180 Values: 0 = Disable 1 = Enable <MonitorRepetitionRates></MonitorRepetitionRates> Description Monitor Stream repetition rates enable or disable <MTM400Configuration> → <Streams> → <Stream> → Path <MonitorRepetitionRates> Data Value Type: Numeral Values: 0 = Enable 1 = Disable MTM400 MPEG Transport Stream Monitor Technical Reference 2−138...
  • Page 181: Interface Parameters

    Selection: Use the <LBandSettings> Name attribute to indicate which collection of LBand settings should be activated. Update: Indicates that existing settings should be either completely replaced (Absolute) or supplemented (Incremental). Child Element <LBandSettings> MTM400 MPEG Transport Stream Monitor Technical Reference 2−139...
  • Page 182 (<Transponder_Frequency>). If the IF frequency is specified, it must be in the range 0.950 GHz to 2.150 GHz; the tuning increment is 125 kHz. <MTM400Configuration> → <Streams> → <Stream> → <LBand> → Path <LBandSettings> → <TransponderFrequency> Data Value Type: Numeral Unit: MTM400 MPEG Transport Stream Monitor Technical Reference 2−140...
  • Page 183 (0) or not (1). <MTM400Configuration> → <Streams> → <Stream> → <LBand> → Path <LBandSettings> → <ViterbiRateAuto> Data Value Type: Numeral Values: 0 = Viterbi Rate Auto Off 1 = Viterbi Rate Auto On MTM400 MPEG Transport Stream Monitor Technical Reference 2−141...
  • Page 184 QAM channel name. For example: QAM 1. Up to 128 QAM channels can be specified. Child Element <Frequency>, <SymbolRate>, <TwoLoFrequency>, <Constellation>, <Inversion>, <LoopBWide>, <AFCwide>, <Troubleshoot> Data Value Type: Text Range: Up to 32 characters MTM400 MPEG Transport Stream Monitor Technical Reference 2−142...
  • Page 185 <MTM400Configuration> → <Streams> → <Stream> → <QAM> → Path <QAMSettings> → <Constellation> Data Value Type: Numeral Values: 0 = Constellation 4 1 = Constellation 16 2 = Constellation 64 3 = Constellation 256 MTM400 MPEG Transport Stream Monitor Technical Reference 2−143...
  • Page 186 (Wide mode). This increases the loop bandwidth to about 10 kHz, which enables the MTM400 to more easily acquire and track a jittered constellation, but makes the demodulator more susceptible to thermal noise.
  • Page 187: Stream Parameters

    RF data and constellations even if the MPEG data is not valid. In QAM mode, the MTM400 behaves more like a conventional QAM analyzer. MPEG mode is the default setting and is recommended for most applications. The range controls, LoopBWwide (PLL bandwidth) and AFCwide (AFC range), are operable in both MPEG and QAM analysis modes.
  • Page 188 EIT basic schedule (TV) number of segments in cycle group 2 Nominal Maximum Minimum Units Integer w 0 PS119 EIT basic schedule (TV) number of segments in cycle group 3 Nominal Maximum Minimum Units Integer w 0 MTM400 MPEG Transport Stream Monitor Technical Reference 2−146...
  • Page 189 EIT extended schedule (TV) number of segments in cycle group 3 Nominal Maximum Minimum Units Integer w 0 PS129 EIT extended schedule (Sound) number of segments in cycle group 1 Nominal Maximum Minimum Units Integer w 0 MTM400 MPEG Transport Stream Monitor Technical Reference 2−147...
  • Page 190 EIT basic schedule (TV) max cycle group 2 repetition interval Nominal Maximum Minimum Units 20000 468000 1000 PS138 EIT basic schedule (TV) max cycle group 3 repetition interval Nominal Maximum Minimum Units 30000 468000 1000 MTM400 MPEG Transport Stream Monitor Technical Reference 2−148...
  • Page 191 EIT basic schedule (Data) max cycle group 2 repetition interval Nominal Maximum Minimum Units 30000 468000 1000 PS146 EIT basic schedule (Data) max cycle group 3 repetition interval Nominal Maximum Minimum Units 30000 468000 1000 MTM400 MPEG Transport Stream Monitor Technical Reference 2−149...
  • Page 192 EIT extended schedule (Sound) max cycle group 3 repetition interval Nominal Maximum Minimum Units 30000 468000 1000 PS155 EIT extended schedule (Data) max basic repetition interval Nominal Maximum Minimum Units 30000 468000 1000 ISDB_T 120000 468000 1000 MTM400 MPEG Transport Stream Monitor Technical Reference 2−150...
  • Page 193 Integer w 0 Integer w 0 ISDB_T PS163 EIT extended schedule (TV) range Nominal Maximum Minimum Units Integer w 0 PS164 EIT extended schedule (Sound) range Nominal Maximum Minimum Units Integer w 0 MTM400 MPEG Transport Stream Monitor Technical Reference 2−151...
  • Page 194 Nominal Maximum Minimum Units ISDB_T PS171 SDTT(L) max repetition interval Nominal Maximum Minimum Units 234000 400000 1000 ISDB_T 360000 400000 1000 PS172 SDTT(L) min section repetition interval Nominal Maximum Minimum Units ISDB_T MTM400 MPEG Transport Stream Monitor Technical Reference 2−152...
  • Page 195 PCR_OJ/AC high-pass filter cutoff (0 for same as DR/FO filter cutoff) Nominal Maximum Minimum Units 10000 PS184 DII min repetition interval Nominal Maximum Minimum Units 300000 PS185 DII max repetition interval Nominal Maximum Minimum Units 5000 300000 MTM400 MPEG Transport Stream Monitor Technical Reference 2−153...
  • Page 196 Minimum Units Integer w 0 PS201 MER absolute limit Nominal Maximum Minimum Units PS202 MER drift limit Nominal Maximum Minimum Units 30000 30000 mdB/hr PS203 EVM absolute limit Nominal Maximum Minimum Units MTM400 MPEG Transport Stream Monitor Technical Reference 2−154...
  • Page 197 BER Post RS drift limit Nominal Maximum Minimum Units 100000000 100000000 per 10e9/hr PS211 TEF abs limit Nominal Maximum Minimum Units 10000000 10000000 TEFs/hr PS212 TEF drift limit Nominal Maximum Minimum Units 10000000 10000000 TEFs/hr/hr MTM400 MPEG Transport Stream Monitor Technical Reference 2−155...
  • Page 198 SDT actual obsolescence count Nominal Maximum Minimum Units integer > 0 PS220 Carrier offset limit Nominal Maximum Minimum Units 1000000 1000000 PS221 Carrier offset drift limit Nominal Maximum Minimum Units 10000 10000 Hz/hr MTM400 MPEG Transport Stream Monitor Technical Reference 2−156...
  • Page 199 Minimum Units 100000000 100000000 per 10e9/hr PS23 SDT other min section repetition interval Nominal Maximum Minimum Units ISDB_T PS230 BER POST RS warning limit Nominal Maximum Minimum Units 100000000 100000000 per 10e9 MTM400 MPEG Transport Stream Monitor Technical Reference 2−157...
  • Page 200 SNR drift warning limit Nominal Maximum Minimum Units 100000 100000 mdB/hr PS239 CNR warning limit Nominal Maximum Minimum Units PS24 SDT other max repetition interval Nominal Maximum Minimum Units 10000 30000 1000 MTM400 MPEG Transport Stream Monitor Technical Reference 2−158...
  • Page 201 NIM max repetition interval Nominal Maximum Minimum Units 1500 30000 1000 PS248 NIM obsolescence count Nominal Maximum Minimum Units integer > 0 PS249 NTM max repetition interval Nominal Maximum Minimum Units 1500 30000 1000 MTM400 MPEG Transport Stream Monitor Technical Reference 2−159...
  • Page 202 8137 8191 PS257 Partial Reception PMT PID #2 Nominal Maximum Minimum Units integer w 0 8138 8191 PS258 Partial Reception PMT PID #3 Nominal Maximum Minimum Units integer w 0 8139 8191 MTM400 MPEG Transport Stream Monitor Technical Reference 2−160...
  • Page 203 Nominal Maximum Minimum Units 10000 Pkts/m PS267 Corrupted packets per second limit warning limit Nominal Maximum Minimum Units 10000 Pkts/m PS269 Dropped packets per second limit Nominal Maximum Minimum Units 10000 Pkts/m MTM400 MPEG Transport Stream Monitor Technical Reference 2−161...
  • Page 204 > 0 PS284 Process DSMCC Nominal Maximum Minimum Units bool PS288 EAS max section repetition interval Nominal Maximum Minimum Units 1000 2000 PS289 EAS obsolescence count Nominal Maximum Minimum Units integer > 0 MTM400 MPEG Transport Stream Monitor Technical Reference 2−162...
  • Page 205 > 0 PS35 EIT other schedule min section repetition interval Nominal Maximum Minimum Units ISDB_T PS36 EIT other schedule max repetition interval Nominal Maximum Minimum Units 10000 600000 2000 ISDB_T 360000 600000 2000 MTM400 MPEG Transport Stream Monitor Technical Reference 2−163...
  • Page 206 BAT min section repetition interval Nominal Maximum Minimum Units PS44 BAT max repetition interval Nominal Maximum Minimum Units 10000 50000 2000 PS45 BAT obsolescence count Nominal Maximum Minimum Units integer > 0 MTM400 MPEG Transport Stream Monitor Technical Reference 2−164...
  • Page 207 PS52 ETT max repetition interval Nominal Maximum Minimum Units 20000 PS53 ETT obsolescence count Nominal Maximum Minimum Units integer > 0 PS54 MIP max repetition interval Nominal Maximum Minimum Units 1500 3000 MTM400 MPEG Transport Stream Monitor Technical Reference 2−165...
  • Page 208 MGT obsolescence count Nominal Maximum Minimum Units integer > 0 PS65 VCT obsolescence count Nominal Maximum Minimum Units integer > 0 PS66 RRT obsolescence count Nominal Maximum Minimum Units integer > 0 MTM400 MPEG Transport Stream Monitor Technical Reference 2−166...
  • Page 209 PAT section max repetition interval Nominal Maximum Minimum Units ATSC 5000 ATSC 5000 PS80 LIT obsolescence count Nominal Maximum Minimum Units integer > 0 PS81 LIT max repetition interval Nominal Maximum Minimum Units 10000 30000 1000 MTM400 MPEG Transport Stream Monitor Technical Reference 2−167...
  • Page 210 PMT section max repetition interval Nominal Maximum Minimum Units 25000 ATSC 25000 ISDB_T 25000 PS91 VCT max section repetition interval Nominal Maximum Minimum Units 3000 PS94 CDT obsolescence count Nominal Maximum Minimum Units integer > 0 MTM400 MPEG Transport Stream Monitor Technical Reference 2−168...
  • Page 211 Path Data Value Type: Text <PS60></PS60> Description ATSC broadcast type <MTM400Configuration> → <Streams> → <Stream> → <PS60> Path Data Value Type: Numeral Values: 0 = Terrestrial 1 = Cable 2 = Either MTM400 MPEG Transport Stream Monitor Technical Reference 2−169...
  • Page 212: Template Parameters

    Path <NetworkId> <OriginalNetworkId></OriginalNetworkId> Description Match with DVB original_network_id for the actual transport stream in the NIT; must be omitted for ATSC operation <MTM400Configuration> → <Streams> → <Stream> → <PS56> → Path <OriginalNetworkId> MTM400 MPEG Transport Stream Monitor Technical Reference 2−170...
  • Page 213 <MTM400Configuration> → <Streams> → <Stream> → <PS56> → Path <ServiceListUpdate> → <Service> → <Constraint> Data Value Type: Integer Values: 0 = Must be present 1 = May be present 2 = Must not be present MTM400 MPEG Transport Stream Monitor Technical Reference 2−171...
  • Page 214 <ServiceListUpdate> → <Service> → <OtherPIDsAllowed> Data Value Type: Boolean <PIDList Update= "><PIDList> Description Container for all PID settings <MTM400Configuration> → <Streams> → <Stream> → <PS56> → Path <ServiceListUpdate> → <Service> → <PIDList> Child Element <PID> MTM400 MPEG Transport Stream Monitor Technical Reference 2−172...
  • Page 215 PID. <MTM400Configuration> → <Streams> → <Stream> → <PS56> → Path <ServiceListUpdate> → <Service> → <PIDList> → <PID> → <CADescriptorPresent> Data Value Type: Boolean MTM400 MPEG Transport Stream Monitor Technical Reference 2−173...
  • Page 216 <MTM400Configuration> → <Streams> → <Stream> → <PS56> → Path <ServiceListUpdate> → <Service> → <RatingList> → <DVBRatingList> → <DVBRatingTemplate> Attribute Country: The country_code from the parental_rating_descriptor in the EIT present table for this service. For example: FRA. Child Element <DVBAcceptableValues> MTM400 MPEG Transport Stream Monitor Technical Reference 2−174...
  • Page 217 Container for all ATSC country-specific ratings <MTM400Configuration> → <Streams> → <Stream> → <PS56> → Path <ServiceListUpdate> → <Service> → <RatingList> → <ATSCRatingList> → <ATSCRatingTemplate> Attribute Region: rating_region from the country_advisory_descriptor. Child Element <ATSCAcceptableValues> MTM400 MPEG Transport Stream Monitor Technical Reference 2−175...
  • Page 218 <ATSCRatingList> → <ATSCRatingTemplate> → <ATSCAcceptableValues> Attribute None Child Element <ATSCRatingValue> <ATSCRatingValue></ATSCRatingValue> Description <MTM400Configuration> → <Streams> → <Stream> → <PS56> → Path <ServiceListUpdate> → <Service> → <RatingList> → <ATSCRatingList> → <ATSCRatingTemplate> → <ATSCAcceptableValues> → <ATSCRatingValue> MTM400 MPEG Transport Stream Monitor Technical Reference 2−176...
  • Page 219: Pid Parameters

    Units integer > 0 PP16 Minimum bit rate permitted for this PID Nominal Maximum Minimum Units 1000 80000 1000 PP17 Partial Reception PCR max repetition interval Nominal Maximum Minimum Units ISDB_T 5000 MTM400 MPEG Transport Stream Monitor Technical Reference 2−177...
  • Page 220 PSK Maximum PCR accuracy error Nominal Maximum Minimum Units 50000 PP31 PSK Maximum PCR overall jitter Nominal Maximum Minimum Units 25000 250000 PP32 PSK Maximum PCR frequency offset Nominal Maximum Minimum Units 30000 MTM400 MPEG Transport Stream Monitor Technical Reference 2−178...
  • Page 221 COFDM Max PCR accuracy error Nominal Maximum Minimum Units 50000 PP51 COFDM Max PCR overall jitter Nominal Maximum Minimum Units 25000 250000 PP52 COFDM Maximum PCR frequency offset Nominal Maximum Minimum Units 30000 MTM400 MPEG Transport Stream Monitor Technical Reference 2−179...
  • Page 222 Minimum PID bit rate Nominal Maximum Minimum Units −1 300000000 PID bit rate variability integration count Nominal Maximum Minimum Units integer > 0 PID bit rate variability fraction Nominal Maximum Minimum Units fraction MTM400 MPEG Transport Stream Monitor Technical Reference 2−180...
  • Page 223: Pid Groups Parameters

    List of PIDs in the group <MTM400Configuration> → <Streams> → <Stream> → Path <PIDGroups> → <PIDGroup> → <PG1> Data Value Type: Space separated integers Example: 1 16 345 789 1010 1344 2040 8190 MTM400 MPEG Transport Stream Monitor Technical Reference 2−181...
  • Page 224: Events Parameters

    <Event ID= "><Event> Description Container for individual Event settings <MTM400Configuration> → <Streams> → <Stream> → <Events> → Path <Event> Attribute ID: Unique event identity. Hex number format. For example: 0x1000. Child Elements <Enabled>, <AlarmSetting> MTM400 MPEG Transport Stream Monitor Technical Reference 2−182...
  • Page 225 <AlarmSetting> (see Figure 2−1). <MTM400Configuration> → <Streams> → <Stream> → <Events> → Path <Event> → <AlarmSetting> MTM400 MPEG Transport Stream Monitor Technical Reference 2−183...
  • Page 226: Service Log Parameters

    Description List of PIDs in the group <MTM400Configuration> → <Streams> → <Stream> → <ServiceLog> Path → <PIDS> Data Value Type: Space separated integers Example: 1 16 345 789 1010 1344 2040 8190 MTM400 MPEG Transport Stream Monitor Technical Reference 2−184...
  • Page 227: Trap Setting Parameters

    <MTM400Configuration> → <Streams> → <Stream> → <TrapSettings> Path → <TrapThrottle> Data Value Type: Integer Range: 0 to 1000 <TrapSinks></TrapSinks> Description Container for TrapSink <MTM400Configuration> → <Streams> → <Stream> → <TrapSettings> Path → <TrapSinks> MTM400 MPEG Transport Stream Monitor Technical Reference 2−185...
  • Page 228: Common Interface Protocol Parameters

    Container for CIP settings <MTM400Configuration> → <Streams> → <Stream> → <CIPConfi- Path guration> Child Elements <!-- Card specific XML --> Example Configuration File An example of a configuration file is given on page 3−6. MTM400 MPEG Transport Stream Monitor Technical Reference 2−186...
  • Page 229: Event Snmp Traps

    Event SNMP Traps In the MTM400, traps are used to report alerts or other asynchronous events generated by the core program. The MTM400 Programmer Manual describes the MIB (Management Information Base), which generates the SNMP traps. The following tables show the SNMP (Simple Network Management Protocol) traps that are available for each Event Identity.
  • Page 230 12328 0x3028 12345 0x3039 12346 0x303A 12355 0x3043 12356 0x3044 12357 0x3045 12371 0x3053 12544 0x3100 12545 0x3101 12546 0x3102 12548 0x3104 12551 0x3107 12564 0x3114 12565 0x3115 12567 0x3117 12568 0x3118 MTM400 MPEG Transport Stream Monitor Technical Reference 2−188...
  • Page 231 14341 0x3805 14342 0x3806 14343 0x3807 14344 0x3808 14345 0x3809 14346 0x380A 14349 0x380D 14350 0x380E 14351 0x380F 14352 0x3810 14353 0x3811 14354 0x3812 14355 0x3813 14356 0x3814 14357 0x3815 14371 0x3823 MTM400 MPEG Transport Stream Monitor Technical Reference 2−189...
  • Page 232 20995 0x5203 24592 0x6010 24608 0x6020 24624 0x6030 24640 0x6040 24848 0x6110 24864 0x6120 24880 0x6130 24896 0x6140 24912 0x6150 25104 0x6210 25120 0x6220 25136 0x6230 25152 0x6240 25345 0x6301 45072 0xB010 MTM400 MPEG Transport Stream Monitor Technical Reference 2−190...
  • Page 233 49171 0xC013 49172 0xC014 49173 0xC015 49174 0xC016 49175 0xC017 49176 0xC018 49177 0xC019 49178 0xC01A 49179 0xC01B 49184 0xC020 49185 0xC021 49186 0xC022 49187 0xC023 49188 0xC024 49189 0xC025 49190 0xC026 MTM400 MPEG Transport Stream Monitor Technical Reference 2−191...
  • Page 234: Table 2−5: Event Snmp Traps - Dvb

    4164 0x1044 4609 0x1201 4610 0x1202 4612 0x1204 4614 0x1206 4615 0x1207 4616 0x1208 4617 0x1209 4625 0x1211 4626 0x1212 4629 0x1215 4630 0x1216 8195 0x2003 8196 0x2004 8209 0x2011 12305 0x3011 MTM400 MPEG Transport Stream Monitor Technical Reference 2−192...
  • Page 235 12550 0x3106 12551 0x3107 12553 0x3109 12561 0x3111 12562 0x3112 12563 0x3113 12564 0x3114 12565 0x3115 12567 0x3117 12568 0x3118 12575 0x311F 12576 0x3120 12582 0x3126 12594 0x3132 12595 0x3133 12640 0x3160 MTM400 MPEG Transport Stream Monitor Technical Reference 2−193...
  • Page 236 13575 0x3507 13576 0x3508 13577 0x3509 13598 0x351E 13599 0x351F 13824 0x3600 14085 0x3705 14091 0x370B 14097 0x3711 14098 0x3712 14101 0x3715 14102 0x3716 14111 0x371F 14120 0x3728 14121 0x3729 14122 0x372A MTM400 MPEG Transport Stream Monitor Technical Reference 2−194...
  • Page 237 14140 0x373C 14141 0x373D 14142 0x373E 14143 0x373F 14336 0x3800 14337 0x3801 14338 0x3802 14339 0x3803 14340 0x3804 14341 0x3805 14342 0x3806 14343 0x3807 14344 0x3808 14345 0x3809 14346 0x380A 14349 0x380D MTM400 MPEG Transport Stream Monitor Technical Reference 2−195...
  • Page 238 14419 0x3853 14420 0x3854 14421 0x3855 14422 0x3856 14423 0x3857 14672 0x3950 14673 0x3951 14674 0x3952 14675 0x3953 14676 0x3954 14677 0x3955 14678 0x3956 14679 0x3957 14680 0x3958 14681 0x3959 14682 0x395A MTM400 MPEG Transport Stream Monitor Technical Reference 2−196...
  • Page 239 25152 0x6240 25345 0x6301 45072 0xB010 45312 0xB100 49153 0xC001 49154 0xC002 49155 0xC003 49156 0xC004 49157 0xC005 49158 0xC006 49159 0xC007 49160 0xC008 49161 0xC009 49162 0xC00A 49163 0xC00B 49166 0xC00E MTM400 MPEG Transport Stream Monitor Technical Reference 2−197...
  • Page 240 49172 0xC014 49173 0xC015 49174 0xC016 49175 0xC017 49176 0xC018 49177 0xC019 49178 0xC01A 49179 0xC01B 49184 0xC020 49185 0xC021 49186 0xC022 49187 0xC023 49188 0xC024 49189 0xC025 49190 0xC026 49191 0xC027 MTM400 MPEG Transport Stream Monitor Technical Reference 2−198...
  • Page 241: Table 2−6: Event Snmp Traps - Atsc

    4629 0x1215 4630 0x1216 8195 0x2003 8196 0x2004 8209 0x2011 12305 0x3011 12306 0x3012 12311 0x3017 12321 0x3021 12322 0x3022 12328 0x3028 12345 0x3039 12346 0x303A 12355 0x3043 12356 0x3044 12357 0x3045 MTM400 MPEG Transport Stream Monitor Technical Reference 2−199...
  • Page 242 13088 0x3320 13104 0x3330 13106 0x3332 13568 0x3500 13569 0x3501 13570 0x3502 13578 0x350A 13579 0x350B 13580 0x350C 13581 0x350D 13582 0x350E 13583 0x350F 13584 0x3510 13585 0x3511 13824 0x3600 14119 0x3727 MTM400 MPEG Transport Stream Monitor Technical Reference 2−200...
  • Page 243 14345 0x3809 14346 0x380A 14349 0x380D 14350 0x380E 14351 0x380F 14352 0x3810 14353 0x3811 14354 0x3812 14355 0x3813 14356 0x3814 14357 0x3815 14371 0x3823 14372 0x3824 14373 0x3825 14375 0x3827 14376 0x3828 MTM400 MPEG Transport Stream Monitor Technical Reference 2−201...
  • Page 244 24624 0x6030 24640 0x6040 24848 0x6110 24864 0x6120 24880 0x6130 24896 0x6140 24912 0x6150 25104 0x6210 25120 0x6220 25136 0x6230 25152 0x6240 25345 0x6301 45072 0xB010 45312 0xB100 49153 0xC001 49154 0xC002 MTM400 MPEG Transport Stream Monitor Technical Reference 2−202...
  • Page 245 49172 0xC014 49173 0xC015 49174 0xC016 49175 0xC017 49176 0xC018 49177 0xC019 49178 0xC01A 49179 0xC01B 49184 0xC020 49185 0xC021 49186 0xC022 49187 0xC023 49188 0xC024 49189 0xC025 49190 0xC026 49191 0xC027 MTM400 MPEG Transport Stream Monitor Technical Reference 2−203...
  • Page 246: Table 2−7: Event Snmp Traps - Isdb-S

    4629 0x1215 4630 0x1216 8195 0x2003 8196 0x2004 8209 0x2011 12305 0x3011 12306 0x3012 12311 0x3017 12321 0x3021 12322 0x3022 12328 0x3028 12345 0x3039 12346 0x303A 12355 0x3043 12356 0x3044 12357 0x3045 MTM400 MPEG Transport Stream Monitor Technical Reference 2−204...
  • Page 247 12595 0x3133 12640 0x3160 13104 0x3330 13105 0x3331 13568 0x3500 13569 0x3501 13570 0x3502 13571 0x3503 13572 0x3504 13573 0x3505 13574 0x3506 13575 0x3507 13576 0x3508 13577 0x3509 13598 0x351E 13599 0x351F MTM400 MPEG Transport Stream Monitor Technical Reference 2−205...
  • Page 248 14139 0x373B 14140 0x373C 14141 0x373D 14142 0x373E 14143 0x373F 14147 0x3743 14148 0x3744 14208 0x3780 14209 0x3781 14225 0x3791 14226 0x3792 14233 0x3799 14318 0x37EE 14319 0x37EF 14336 0x3800 14337 0x3801 MTM400 MPEG Transport Stream Monitor Technical Reference 2−206...
  • Page 249 14357 0x3815 14371 0x3823 14372 0x3824 14373 0x3825 14375 0x3827 14376 0x3828 14377 0x3829 14416 0x3850 14417 0x3851 14418 0x3852 14419 0x3853 14420 0x3854 14421 0x3855 14422 0x3856 14423 0x3857 14597 0x3905 MTM400 MPEG Transport Stream Monitor Technical Reference 2−207...
  • Page 250 24848 0x6110 24864 0x6120 24880 0x6130 24896 0x6140 24912 0x6150 25104 0x6210 25120 0x6220 25136 0x6230 25152 0x6240 25345 0x6301 45072 0xB010 45312 0xB100 49153 0xC001 49154 0xC002 49155 0xC003 49156 0xC004 MTM400 MPEG Transport Stream Monitor Technical Reference 2−208...
  • Page 251 49172 0xC014 49173 0xC015 49174 0xC016 49175 0xC017 49176 0xC018 49177 0xC019 49178 0xC01A 49179 0xC01B 49184 0xC020 49185 0xC021 49186 0xC022 49187 0xC023 49188 0xC024 49189 0xC025 49190 0xC026 49191 0xC027 MTM400 MPEG Transport Stream Monitor Technical Reference 2−209...
  • Page 252: Table 2−8: Event Snmp Traps - Isdb-T

    4629 0x1215 4630 0x1216 8195 0x2003 8196 0x2004 8209 0x2011 12305 0x3011 12306 0x3012 12311 0x3017 12321 0x3021 12322 0x3022 12328 0x3028 12345 0x3039 12346 0x303A 12355 0x3043 12356 0x3044 12357 0x3045 MTM400 MPEG Transport Stream Monitor Technical Reference 2−210...
  • Page 253 12574 0x311E 12575 0x311F 12582 0x3126 12594 0x3132 12595 0x3133 12640 0x3160 13104 0x3330 13105 0x3331 13568 0x3500 13569 0x3501 13570 0x3502 13571 0x3503 13572 0x3504 13573 0x3505 13575 0x3507 13576 0x3508 MTM400 MPEG Transport Stream Monitor Technical Reference 2−211...
  • Page 254 14125 0x372D 14126 0x372E 14127 0x372F 14128 0x3730 14129 0x3731 14130 0x3732 14139 0x373B 14140 0x373C 14141 0x373D 14142 0x373E 14143 0x373F 14145 0x3741 14146 0x3742 14147 0x3743 14148 0x3744 14157 0x374D MTM400 MPEG Transport Stream Monitor Technical Reference 2−212...
  • Page 255 14259 0x37B3 14273 0x37C1 14274 0x37C2 14275 0x37C3 14276 0x37C4 14277 0x37C5 14288 0x37D0 14289 0x37D1 14290 0x37D2 14291 0x37D3 14292 0x37D4 14293 0x37D5 14294 0x37D6 14295 0x37D7 14296 0x37D8 14297 0x37D9 MTM400 MPEG Transport Stream Monitor Technical Reference 2−213...
  • Page 256 14319 0x37EF 14320 0x37F0 14321 0x37F1 14336 0x3800 14337 0x3801 14338 0x3802 14339 0x3803 14340 0x3804 14341 0x3805 14342 0x3806 14343 0x3807 14344 0x3808 14345 0x3809 14346 0x380A 14349 0x380D 14350 0x380E MTM400 MPEG Transport Stream Monitor Technical Reference 2−214...
  • Page 257 14420 0x3854 14421 0x3855 14422 0x3856 14423 0x3857 14597 0x3905 14601 0x3909 14605 0x390D 14607 0x390F 14672 0x3950 14673 0x3951 14674 0x3952 14675 0x3953 14676 0x3954 14682 0x395A 20992 0x5200 20993 0x5201 MTM400 MPEG Transport Stream Monitor Technical Reference 2−215...
  • Page 258 45312 0xB100 49153 0xC001 49154 0xC002 49155 0xC003 49156 0xC004 49157 0xC005 49158 0xC006 49159 0xC007 49160 0xC008 49161 0xC009 49162 0xC00A 49163 0xC00B 49166 0xC00E 49167 0xC00F 49168 0xC010 49169 0xC011 MTM400 MPEG Transport Stream Monitor Technical Reference 2−216...
  • Page 259: Table 2−9: Event Snmp Traps - Isdb (Partial Reception)

    Event TSID Network Service Service Thresh- Actual Duration Stream Identity – Identity – Identity Type Identity Decimal ldentity 4144 0x1030 4145 0x1031 4146 0x1032 4160 0x1040 4161 0x1041 4162 0x1042 4163 0x1043 MTM400 MPEG Transport Stream Monitor Technical Reference 2−217...
  • Page 260 12311 0x3017 12321 0x3021 12322 0x3022 12328 0x3028 12345 0x3039 12346 0x303A 12355 0x3043 12356 0x3044 12357 0x3045 12370 0x3052 12371 0x3053 12545 0x3101 12546 0x3102 12548 0x3104 12550 0x3106 12551 0x3107 MTM400 MPEG Transport Stream Monitor Technical Reference 2−218...
  • Page 261 13570 0x3502 13572 0x3504 13575 0x3507 13576 0x3508 13577 0x3509 13593 0x3519 13594 0x351A 13595 0x351B 13598 0x351E 13599 0x351F 13824 0x3600 14085 0x3705 14091 0x370B 14111 0x371F 14120 0x3728 14121 0x3729 MTM400 MPEG Transport Stream Monitor Technical Reference 2−219...
  • Page 262 14226 0x3792 14233 0x3799 14234 0x379A 14235 0x379B 14236 0x379C 14238 0x379E 14239 0x379F 14240 0x37A0 14242 0x37A2 14243 0x37A3 14245 0x37A5 14246 0x37A6 14257 0x37B1 14275 0x37C3 14276 0x37C4 14277 0x37C5 MTM400 MPEG Transport Stream Monitor Technical Reference 2−220...
  • Page 263 14351 0x380F 14352 0x3810 14353 0x3811 14354 0x3812 14355 0x3813 14356 0x3814 14357 0x3815 14371 0x3823 14372 0x3824 14373 0x3825 14375 0x3827 14376 0x3828 14377 0x3829 14416 0x3850 14417 0x3851 14418 0x3852 MTM400 MPEG Transport Stream Monitor Technical Reference 2−221...
  • Page 264 24592 0x6010 24608 0x6020 24624 0x6030 24640 0x6040 24848 0x6110 24864 0x6120 24880 0x6130 24896 0x6140 24912 0x6150 25104 0x6210 25120 0x6220 25136 0x6230 25152 0x6240 25345 0x6301 45072 0xB010 45312 0xB100 MTM400 MPEG Transport Stream Monitor Technical Reference 2−222...
  • Page 265 49171 0xC013 49172 0xC014 49173 0xC015 49174 0xC016 49175 0xC017 49176 0xC018 49177 0xC019 49178 0xC01A 49179 0xC01B 49183 0xC01F 49184 0xC020 49185 0xC021 49186 0xC022 49187 0xC023 49188 0xC024 49189 0xC025 MTM400 MPEG Transport Stream Monitor Technical Reference 2−223...
  • Page 266: Table 2−10: Event Snmp Traps -Dcii

    4609 0x1201 4610 0x1202 4612 0x1204 4614 0x1206 4615 0x1207 4616 0x1208 4617 0x1209 4625 0x1211 4626 0x1212 4629 0x1215 4630 0x1216 8195 0x2003 8196 0x2004 8209 0x2011 12305 0x3011 12306 0x3012 MTM400 MPEG Transport Stream Monitor Technical Reference 2−224...
  • Page 267 12567 0x3117 12568 0x3118 12594 0x3132 12595 0x3133 12640 0x3160 13104 0x3330 13568 0x3500 13569 0x3501 13570 0x3502 13587 0x3513 13588 0x3514 13589 0x3515 13590 0x3516 13591 0x3517 13592 0x3518 13824 0x3600 MTM400 MPEG Transport Stream Monitor Technical Reference 2−225...
  • Page 268 14350 0x380E 14351 0x380F 14352 0x3810 14353 0x3811 14354 0x3812 14355 0x3813 14356 0x3814 14357 0x3815 14371 0x3823 14372 0x3824 14373 0x3825 14375 0x3827 14376 0x3828 14377 0x3829 14384 0x3830 14385 0x3831 MTM400 MPEG Transport Stream Monitor Technical Reference 2−226...
  • Page 269 20996 0x5204 24592 0x6010 24640 0x6040 24848 0x6110 24864 0x6120 24880 0x6130 24896 0x6140 24912 0x6150 25104 0x6210 25120 0x6220 25136 0x6230 25152 0x6240 25345 0x6301 45072 0xB010 45312 0xB100 49153 0xC001 MTM400 MPEG Transport Stream Monitor Technical Reference 2−227...
  • Page 270 49172 0xC014 49173 0xC015 49174 0xC016 49175 0xC017 49176 0xC018 49177 0xC019 49178 0xC01A 49179 0xC01B 49184 0xC020 49185 0xC021 49186 0xC022 49187 0xC023 49188 0xC024 49189 0xC025 49190 0xC026 49191 0xC027 MTM400 MPEG Transport Stream Monitor Technical Reference 2−228...
  • Page 271: Table 2−11: Event Snmp Traps - China

    4629 0x1215 4630 0x1216 8195 0x2003 8196 0x2004 8209 0x2011 12305 0x3011 12306 0x3012 12311 0x3017 12321 0x3021 12322 0x3022 12328 0x3028 12345 0x3039 12346 0x303A 12355 0x3043 12356 0x3044 12357 0x3045 MTM400 MPEG Transport Stream Monitor Technical Reference 2−229...
  • Page 272 12575 0x311F 12576 0x3120 12582 0x3126 12594 0x3132 12595 0x3133 12640 0x3160 13104 0x3330 13105 0x3331 13316 0x3404 13328 0x3410 13329 0x3411 13330 0x3412 13331 0x3413 13332 0x3414 13333 0x3415 13334 0x3416 MTM400 MPEG Transport Stream Monitor Technical Reference 2−230...
  • Page 273 14101 0x3715 14102 0x3716 14111 0x371F 14120 0x3728 14121 0x3729 14122 0x372A 14123 0x372B 14124 0x372C 14125 0x372D 14126 0x372E 14127 0x372F 14128 0x3730 14129 0x3731 14130 0x3732 14131 0x3733 14132 0x3734 MTM400 MPEG Transport Stream Monitor Technical Reference 2−231...
  • Page 274 14342 0x3806 14343 0x3807 14344 0x3808 14345 0x3809 14346 0x380A 14349 0x380D 14350 0x380E 14351 0x380F 14352 0x3810 14353 0x3811 14354 0x3812 14355 0x3813 14356 0x3814 14357 0x3815 14371 0x3823 14372 0x3824 MTM400 MPEG Transport Stream Monitor Technical Reference 2−232...
  • Page 275 14677 0x3955 14678 0x3956 14679 0x3957 14680 0x3958 14681 0x3959 14682 0x395A 14683 0x395B 20992 0x5200 20993 0x5201 20994 0x5202 20995 0x5203 24592 0x6010 24608 0x6020 24624 0x6030 24640 0x6040 24848 0x6110 MTM400 MPEG Transport Stream Monitor Technical Reference 2−233...
  • Page 276 49159 0xC007 49160 0xC008 49161 0xC009 49162 0xC00A 49163 0xC00B 49166 0xC00E 49167 0xC00F 49168 0xC010 49169 0xC011 49170 0xC012 49171 0xC013 49172 0xC014 49173 0xC015 49174 0xC016 49175 0xC017 49176 0xC018 MTM400 MPEG Transport Stream Monitor Technical Reference 2−234...
  • Page 277: Table 2−12: Event Snmp Traps - Ip

    Table 2−12: Event SNMP Traps - IP Event Identity – Event Identity – Test Event Source IP Destination IP Destination Port Decimal 36867 0x9003 36869 0x9005 36870 0x9006 36871 0x9007 36872 0x9008 37121 0x9101 37122 0x9102 37123 0x9103 MTM400 MPEG Transport Stream Monitor Technical Reference 2−235...
  • Page 278 Test Parameters - Event SNMP Traps MTM400 MPEG Transport Stream Monitor Technical Reference 2−236...
  • Page 279 Configuration File Structure...
  • Page 281 The file is presented in XML (Extensible Markup Language) format. XML is a hierarchical language that can be interpreted by MTM400 units. It can be edited using either a simple text editor such as Microsoft NotePad, or a more sophisti- cated editor.
  • Page 282: Updating

    <DisabledEvents>0x2004 0x2011 0x3017 0x3028 0x303a 0x3043 0x3044 0x3045 0x3117 0x3118 0x3124 0x3132 0x3133 0x3728</DisabledEvents> </PID> H Ever-present parameters always have current values in the MTM400, for example, <PI1> Interface Selection. They will never be deleted, but may be updated through the configuration file.
  • Page 283: Table 3−1: Absolute Update - Example

    Program 3 </Program> PV1 = 75 kbit/s PV1 = 400 kbit/s </Programs> PV2 = 123 Mbit/s PV2 = 100 Mbit/s ..PV3 = PMT test disabled PV3 = PMT test enabled .... MTM400 MPEG Transport Stream Monitor Technical Reference 3−3...
  • Page 284 <LBandSettings Update = Incremental" Name = Default"> <OscillatorFrequency>355000</OscillatorFrequency> <TransponderFrequency>24000</TransponderFrequency> <PolarVolts>0</PolarVolts> <SymbolRate>27500000</SymbolRate> <ViterbiRate>2</ViterbiRate> <ViterbiRateAuto>1</ViterbiRateAuto> <Tone22K>0</Tone22K> <InvertSpectrum>1</InvertSpectrum> </LBandSettings> Note that the original section was modified, but those tags not specified in the updating file were left unchanged. MTM400 MPEG Transport Stream Monitor Technical Reference 3−4...
  • Page 285: Defaults

    Configuration File Structure Defaults Default values are ‘hardwired’ into the MTM400; they will be used when no value has been given using a configuration file. However for some elements, alternative default values can be supplied, for example, <Program>. If the defaults are supplied through the configuration file, all subsidiaries of that element will use those defaults unless specific values are given.
  • Page 286: Example Configuration File

    <Qam Update = "Incremental" Selection = "QamADefault"> <QamSettings Name = "QamADefault"> <Frequency>474000000</Frequency> <SymbolRate>6900000</SymbolRate> <TwoLoFrequency>43025000</TwoLoFrequency> <Constellation>2</Constellation> <Inversion>1</Inversion> <LoopBWwide>0</LoopBWwide> <AFCwide>0</AFCwide> <TroubleShoot>0</TroubleShoot> </QamSettings> </Qam> <Nic Update = "Incremental"> </Nic> <BroadcastStandard>1</BroadcastStandard> <DvbRegion>5</DvbRegion> <Satellite>1</Satellite> <TmccAcquisition>0</TmccAcquisition> <MpeAcquisition>0</MpeAcquisition> <ResetEventsOnSyncAcquired>0</ResetEventsOnSyncAcquired> <MonitorRepetitionRates>0</MonitorRepetitionRates> <PcrAccuracyMode>1</PcrAccuracyMode> <OS1>60000</OS1> <HoldoffMode>0</HoldoffMode> <TimeStamping>1</TimeStamping> MTM400 MPEG Transport Stream Monitor Technical Reference 3−6...
  • Page 287 <!−− Stream Float Parameters −−> <PP9>0.000000</PP9> <PS56> <ServiceList Update = "Incremental"> <Service Number="25664"> <Constraint>0</Constraint> <ServiceType>1</ServiceType> <ServiceName>The HITS</ServiceName> <PCRPID>101</PCRPID> <OtherPIDsAllowed>0</OtherPIDsAllowed> <PIDList Update = "Incremental"> <PID Number="101"> <Constraint>0</Constraint> <StreamType>2</StreamType> <CADescriptorPresent>0</CADescriptorPresent> <IsScrambled>0</IsScrambled> </PID> <PID Number="102"> MTM400 MPEG Transport Stream Monitor Technical Reference 3−7...
  • Page 288 <PP5>977</PP5> <PP6>328473</PP6> <PP7>9590707</PP7> <PP50>49826</PP50> <PP51>245392</PP51> <PP53>13763</PP53> <DisabledEvents>0x3132</DisabledEvents> </PID> <PID Number="102" ForcePresence="0"> <PP5>1108</PP5> <PP6>95052</PP6> <PP7>240038</PP7> <DisabledEvents>0x3132</DisabledEvents> </PID> </PIDS> <Events Update = "Incremental"> <Event ID="0x1000"> <Enabled>1</Enabled> <TrapClearEnabled>0</TrapClearEnabled> <TrapRaiseEnabled>0</TrapRaiseEnabled> <AlarmSetting>0x0</AlarmSetting> </Event> <Event ID="0x1001"> <Enabled>1</Enabled> <TrapClearEnabled>0</TrapClearEnabled> MTM400 MPEG Transport Stream Monitor Technical Reference 3−8...
  • Page 289 Configuration File Structure <TrapRaiseEnabled>0</TrapRaiseEnabled> <AlarmSetting>0x0</AlarmSetting> </Event> <Event ID="0xc027"> <Enabled>0</Enabled> <TrapClearEnabled>0</TrapClearEnabled> <TrapRaiseEnabled>0</TrapRaiseEnabled> <AlarmSetting>0x0</AlarmSetting> </Event> </Events> <ServiceLog> <PIDS></PIDS> </ServiceLog> <CIPConfiguration> </CIPConfiguration> <TrapSettings> <TrapSinkTimeout>5</TrapSinkTimeout> <TrapThrottle>10</TrapThrottle> <TrapSinks> <TrapSink>192.158.201.138</TrapSink> </TrapSinks> </TrapSettings> </Stream> </Streams> </MTM400Configuration> MTM400 MPEG Transport Stream Monitor Technical Reference 3−9...
  • Page 290 Configuration File Structure MTM400 MPEG Transport Stream Monitor Technical Reference 3−10...
  • Page 291 WARNING The following servicing instructions are for use only by qualified personnel. To avoid injury, do not perform any servicing other than that stated in the operating instructions unless you are qualified to do so. Refer to all safety summaries before performing any service.
  • Page 293 Hardware Maintenance...
  • Page 295: Preventive Maintenance

    Hardware Maintenance This section describes the general care and service procedures for the MTM400 MPEG Transport Stream Monitor and includes the following subsections: H Preventive Maintenance provides cleaning instructions. H Rack Mounting provides instructions for installing the unit in a 19-inch equipment rack.
  • Page 296: Figure 4−1: Chassis Section Rack Slides

    CAUTION. Efficient cooling will be maintained in a rack-mounted unit if the air temperature at all intake air vents (inside the rack) does not exceed 40_C. WARNING. To avoid fire hazard and injury, the MTM400 must be installed in the rack only as specified, and proper ventilation must be maintained.
  • Page 297: Figure 4−2: Rack Mounted Sections

    Installing the MTM400 Unit 1. Pull the slide-out track section to the fully extended position. 2. Insert the MTM400 chassis sections into the slide-out sections. 3. Press the stop latches and push the unit toward the rack until the latches snap into their holes.
  • Page 298: Figure 4−3: Installing Or Removing The Rack Slides

    Once the instrument is in place within the rack, tighten the knurled retaining screw to fasten it securely into the rack. The slide-out tracks do not require lubrication. The dark gray finish on the tracks Rack Slide Maintenance is a permanent, lubricated coating. MTM400 MPEG Transport Stream Monitor Technical Reference 4−4...
  • Page 299: Removing And Replacing An Interface Board

    Removing and Replacing an Interface Board The following procedure describes how to access and replace an interface board. A range of interface boards is available for the MTM400; contact Tektronix for a full list of those available. The principles involved in removing and replacing an interface board is similar;...
  • Page 300: Figure 4−4: Removing The Instrument Cover

    There are three types of interface boards as shown in Figure 4−5, Figure 4−6, and Figure 4−7. Each board type has different cable connections. MTM400 MPEG Transport Stream Monitor Technical Reference 4−6...
  • Page 301: Table 4−1: Qam (Annex A), Qam (Annex B, Old Version Qam (Annex C), And Qpsk (L-Band) Board Connectors

    Connects to location Function Eight wires J7 on Power Distribution board Power Miniature coaxial I/P A on TS Processor board Data (serializer) Miniature coaxial O/P A on TS Processor board Data (serializer) MTM400 MPEG Transport Stream Monitor Technical Reference 4−7...
  • Page 302: Figure 4−5: Qam (Annex A), Qam (Annex B, Old Version), Qam (Annex C), And Qpsk (L-Band) Interface Board Location

    Figure 4−5: QAM (Annex A), QAM (Annex B, old version), QAM (Annex C), and QPSK (L-Band) interface board location Ribbon Eight-wire cable power cable Interface board Figure 4−6: QAM (Annex B, new version), 8PSK, 8VSB, and COFDM interface board location MTM400 MPEG Transport Stream Monitor Technical Reference 4−8...
  • Page 303: Figure 4−7: Gbe Interface Board Installation

    Table 4−2: QAM (Annex B, new version), 8PSK, 8VSB, and COFDM interface board connectors Interface board connection (see Figure 4−6) Cable type Connects to location Function Eight wires J7 on Power Distribution board Power Ribbon J750 on TS Processor board Data (serializer) MTM400 MPEG Transport Stream Monitor Technical Reference 4−9...
  • Page 304: Table 4−3: Gbe Interface Board Connectors

    Figure 4−9. c. For GbE interface boards, remove the six retaining screws from the board and remove the three retaining screws from the rear panel as shown in Figure 4−10. MTM400 MPEG Transport Stream Monitor Technical Reference 4−10...
  • Page 305: Figure 4−8: Retaining Screw Locations For Qam (Annex A), Qam (Annex B, Old Version), Qam (Annex C), And Qpsk (L-Band) Interface Boards

    QAM (Annex C), and QPSK (L-Band) interface boards Retaining screws (6) Retaining screws (3) Figure 4−9: Retaining screw locations for QAM (Annex B, new version), 8PSK, 8VSB, and COFDM interface boards MTM400 MPEG Transport Stream Monitor Technical Reference 4−11...
  • Page 306: Figure 4−10: Retaining Screw Locations For Gbe Interface Board

    CAUTION. To prevent static damage to the removed board, be sure to store the board in static-free packaging. Failure to properly store the board may result in the board needing repair before it will operate properly when reinstalled. MTM400 MPEG Transport Stream Monitor Technical Reference 4−12...
  • Page 307 CAUTION. To prevent damage to the interface board connectors, do not use unnecessary force to connect the cables. All of the connectors are polarized and they will only fit into their respective socket in one way. MTM400 MPEG Transport Stream Monitor Technical Reference 4−13...
  • Page 308: Figure 4−11: Cable Connections For Qam (Annex A), Qam (Annex B, Old Version), Qam (Annex C), And Qpsk (L-Band) Interface Boards

    J7 on the Power Distribution board. Eight-wire Coaxial power cable cables Interface board Figure 4−11: Cable connections for QAM (Annex A), QAM (Annex B, old version), QAM (Annex C), and QPSK (L-Band) interface boards MTM400 MPEG Transport Stream Monitor Technical Reference 4−14...
  • Page 309: Figure 4−12: Cable Connections For Qam (Annex B, New Version)

    H Verify that the two coaxial cables on the interface board are firmly attached to their connectors. Eight-wire cable Ribbon cable Coaxial cables Interface board Figure 4−12: Cable connections for QAM (Annex B, new version), 8PSK, 8VSB, and COFDM interface boards MTM400 MPEG Transport Stream Monitor Technical Reference 4−15...
  • Page 310: Figure 4−13: Cable Connections For Gbe Interface Board

    15. Line up the instrument top cover and replace the 21 retaining screws (see Figure 4−4 on page 4−6). 16. The Interface board will be detected and initialized when the MTM400 unit Select the Interface is switched on. Before the Interface board can be used, it must be selected through the user interface and an input must be provided.
  • Page 311: Battery Maintenance

    Hardware Maintenance Battery Maintenance The MTM400 unit uses a pair of Lithium batteries to provide power to the backup circuits when mains power is off. Under normal circumstances, the shelf life of the batteries is in excess of five years.
  • Page 312 7. Reinstate the network identity of the unit (refer to Network Installation in the MTM400 MPEG Transport Stream Monitor User Manual). 8. If required, reinstate the configuration information. Refer to the MTM400 MPEG Transport Stream Monitor User Manual for instructions on how to restore the configuration settings.
  • Page 313: Repacking For Shipment

    Hardware Maintenance Repacking for Shipment If an instrument is to be shipped to a Tektronix field office for repair, attach a tag to the instrument showing the following: H Owner’s name and address H Serial number H Description of the problem(s) encountered and/or service required.
  • Page 314 Hardware Maintenance MTM400 MPEG Transport Stream Monitor Technical Reference 4−20...
  • Page 315 Glossary...
  • Page 317 Bit Error Rate Conditional Access Table Cyclic Redundancy Check Comma Separated Values CVCT Cable Virtual Channel Table Domain Name Server Digital Video Broadcasting Event Information Table Entitlement Management Message Extended Text Table MTM400 MPEG Transport Stream Monitor Technical Reference Glossary−1...
  • Page 318 Modulation Error Ratio Master Guide Table MHEG Multimedia and Hypermedia Experts Group MPEG Moving Picture Experts Group Network Information Table Program Association Table Peripheral Component Interconnect Program Clock Reference Packet Identifier Program Map Table MTM400 MPEG Transport Stream Monitor Technical Reference Glossary−2...
  • Page 319 SMPTE Society of Motion Picture and Television Engineers SNMP Simple Network Management Protocol Synchronous Serial Interface System Time Table Transport Error Flag TMCC Transmission and Multiplexing Configuration Control (ISDB-S) Time Offset Table MTM400 MPEG Transport Stream Monitor Technical Reference Glossary−3...
  • Page 320 Glossary TSDT Transport Streams Description Table TVCT Terrestrial Virtual Channel Table TVRO Television Receive Only Coordinated Universal Time Virtual Channel Table Extensible Markup Language MTM400 MPEG Transport Stream Monitor Technical Reference Glossary−4...

Table of Contents