Tektronix MTM400A Technical Reference
  1. Manuals
  2. Brands
  3. Tektronix Manuals
  4. Monitor
  5. MTM400A
  6. Technical reference
Tektronix MTM400A Technical Reference

Tektronix MTM400A Technical Reference

Mpeg transport stream monitor
Hide thumbs Also See for MTM400A:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Manual, Technical Reference
Technical Reference
MTM400A
MPEG Transport Stream Monitor
Specifications and Performance Verification
071-2496-00
This document applies to firmware versions 3.0
and above.
www.tektronix.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MTM400A and is the answer not in the manual?

Questions and answers

Related Manuals for Tektronix MTM400A

Summary of Contents for Tektronix MTM400A

  • Page 1 Technical Reference MTM400A MPEG Transport Stream Monitor Specifications and Performance Verification 071-2496-00 This document applies to firmware versions 3.0 and above. www.tektronix.com...
  • Page 2 Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or suppliers, and are protected by national copyright laws and international treaty provisions. Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes that in all previously published material.
  • Page 3 ............2- - 1 MTM400A Specifications and Performance Verification...

  • Page 4: Table Of Contents

    Table of Contents List of Figures Figure 2- -1: MTM400A monitor RUI display ....2- -3 List of Tables Table i: Product documentation .
  • Page 5 ....... . . 1- -19 MTM400A Specifications and Performance Verification...
  • Page 6 Table of Contents MTM400A Specifications and Performance Verification...
  • Page 7 Do Not Operate in Wet/Damp Conditions. Do Not Operate in an Explosive Atmosphere. Keep Product Surfaces Clean and Dry. Provide Proper Ventilation. Refer to the manual’s installation instructions for details on installing the product so it has proper ventilation. MTM400A Specifications and Performance Verification...
  • Page 8 H WARNING indicates an injury hazard not immediately accessible as you read the marking. H CAUTION indicates a hazard to property including the product. The following symbol(s) may appear on the product: Protective Ground CAUTION Refer to Manual (Earth) Terminal MTM400A Specifications and Performance Verification...

  • Page 9: Table I: Product Documentation

    Transport Stream Monitor: H Specifications lists the electrical, physical, and environmental specifications of the MTM400A monitor. H Performance Verification contains a procedure to verify that the MTM400A monitor is operating normally. Product Documentation Table i lists the product documentation supporting the MTM400A monitor.
  • Page 10 Provides instructions for upgrading the (075-0972-xx) product firmware Hardware Upgrade Instructions Provides instructions for installing the (075-0973-xx) optional hardware interface cards Key: Printed document MTM400A product documentation CD - PDF format Tektronix Web site - PDF format viii MTM400A Specifications and Performance Verification...
  • Page 11 Specifications...

  • Page 13: Table 1- 2: Ts Processor Card - System Timing Clock

    Specifications This section lists the electrical, environmental, and physical specifications of the MTM400A monitor. All specifications are guaranteed unless labeled typical. Typical specifications are provided for your convenience and are not guaranteed. Electrical characteristics apply to test systems operating within the environmen- tal conditions.

  • Page 14: Table 1- 3: Ts Processor Card - Asi Interface

    Output Bit Rate Same as the SMPTE310M input 600 mV min, 1.0 V max, into a 75 Ω load Signal Amplitude 75 Ω, transformer coupled Output Impedance Return Loss 10 dB min at 20 MHz 1- 2 MTM400A Specifications and Performance Verification...

  • Page 15: Table 1- 5: Ts Processor Card - Alarm Connector

    Relay 1: Normally open contact RL2NO Relay 2: Normally open contact RL3NO Relay 3: Normally open contact RL4NO Relay 4: Normally open contact RL5NO Relay 5: Normally open contact Connector shell - Chassis ground 1- 3 MTM400A Specifications and Performance Verification...

  • Page 16: Table 1- 6: Ts Processor Card - Alarms

    Linear time code, SMPTE standard to ANSI/SMPTE 12M - 1995 Input Voltage 2.0 V p-p differentially minimum Table 1- 8: TS processor card - Ethernet RJ-45 connector Characteristic Description Connector 10/100 Base-T; RJ-45 Use only good quality screened cable; Cat 6 1- 4 MTM400A Specifications and Performance Verification...

  • Page 17: Table 1- 9: Qam Annex A Interface Card Characteristics

    Receiver Bandwidth, QAM B 6 MHz nominal Connector Type F type 75 Ω nominal Input Termination Impedance Input Return Loss 5 dB typical Ultimate Modulation Error Ratio with Equalizer 37 dB with equalizer; typical 1- 5 MTM400A Specifications and Performance Verification...

  • Page 18: Table 1- 11: Qam Annex B2 Measurements

    38 dB typical, with a 64 QAM input Receiver Bandwidth, QAM C 6 MHz nominal 75 Ω nominal Input Termination Impedance Input Return Loss 6 dB min, 10 dB typical, 88 MHz to 858 MHz 1- 6 MTM400A Specifications and Performance Verification...

  • Page 19: Table 1- 13: 8Psk/Qpsk Interface Card Characteristics With 8Psk Input

    LNB 22 kHz Signaling Frequency 17.6 kHz min, 26.4 kHz max (22 kHz 20%) 600 mV p-p with 100 Ω load LNB 22 kHz Signaling Amplitude Ultimate Modulation Error Ratio (with equalizer) 26 dB with equalizer 1- 7 MTM400A Specifications and Performance Verification...

  • Page 20: Table 1- 15: 8Psk And Qpsk Measurements

    - - 60 dBm to ensure compliance to EN 55103-2 immunity Modulation Format 8VSB in accordance with ATSC A/53B. Receiver Bandwidth 6 MHz 75 Ω nominal Input Termination Impedance Connector Type F type Input Return Loss 5 dB minimum; typical 1- 8 MTM400A Specifications and Performance Verification...

  • Page 21: Table 1- 17: 8Vsb Measurements

    Equalizer filter tap information is displayed. Display Echo Level range: Normalized real tap values over the range of - - 1 to 1 Display Delay range: - - 6.7 μs to 45.5 μs 1- 9 MTM400A Specifications and Performance Verification...

  • Page 22: Table 1- 18: Cofdm Interface Card Characteristics

    1/2, 2/3, 3/4, 5/6, 7/8 Guard Intervals 1/32, 1/16, 1/8, 1/4 Spectrum Polarity The receiver will operate with both inverted and normal spectral polarity. Ultimate Modulation Error Ratio, with Equalizer 37 dB with equalizer; typical 1- 10 MTM400A Specifications and Performance Verification...

  • Page 23: Table 1- 19: Cofdm Measurements

    EVM (Error Vector Magnitude) (Typical) Display Range: 1% to 30% rms, for QPSK 1% to 20% rms, 16QAM 1% to 8.5% rms, 64QAM Resolution: 0.1% Accuracy: 1% (1 EVM unit), and additional 20% of reading 1- 11 MTM400A Specifications and Performance Verification...

  • Page 24: Table 1- 20: Gige Interface Card - General Characteristics

    Table 1- 21: GigE interface card - Ethernet electrical port Characteristic Description Standard 10/100/1000BASE-T IEEE 802.3 Connector Type RJ-45 Data Format 10/100 Base T Data Format 1000 Base T Trellis encoded, PAM5 symbols full-duplex on 4-pair Cat-5 UTP per IEEE 802.3ab 1- 12 MTM400A Specifications and Performance Verification...

  • Page 25: Table 1- 22: Gige Interface Card - Ethernet Optical Port

    Ethernet Optical Receiver - Multimode 850nm Using Tek supplied SFP module - - 12 Optical Input Power - - 17 dBm to 0 dBm, BER 1 X 10 ; typical 770 nm = λ = 860 nm Input Wavelength 1- 13 MTM400A Specifications and Performance Verification...

  • Page 26: Table 1- 23: Gige Interface Card - Asi Input

    Termination Data Format Bi-phase coded. Compliant with SMPTE310M Input Bit Rate 19,392,658.5 bps 2.8 ppm Signal Amplitude 2.0V max; 200 mV pk to pk min Return Loss 10 dB min at 20 MHz 1- 14 MTM400A Specifications and Performance Verification...

  • Page 27: Power Source Characteristics 1

    2 (In single carrier) Voltage Capacity 210 mAh Continuous Discharge (Maximum) 3 mA Overall Dimensions (Single cell) Height 3.2 mm (0.13 in) Width (Diameter) 20 mm (0.79 in) Battery Type Tektronix part number: 146-0096-xx 1- 15 MTM400A Specifications and Performance Verification...

  • Page 28: Environmental Characteristics 1

    Top and bottom: 0 mm; Sides: Standard 19 in rack mount Weight 6.0 kg (13.3 lbs); fully loaded Packaged Dimensions Height 241 mm (9.5 in) Width 590 mm (23.1 in) Depth 760 mm (30 in) Weight (Packaged) 9 kg (19.7 lbs) 1- 16 MTM400A Specifications and Performance Verification...

  • Page 29: Certifications And Compliances 1

    U.S. Nationally Recognized Testing Laboratory UL61010B-1:2003 Standard for electrical measuring and test equipment. Listing Canadian Certification CAN/CSA C22.2 No. 1010.1:1997 Particular requirements for electrical equipment for measurement, control, and laboratory use. Part 1. 1- 17 MTM400A Specifications and Performance Verification...
  • Page 30 Pollution Degree 4 Pollution that generates persistent conductivity through conductive dust, rain, or snow. Typical outdoor locations. Pollution Degree Pollution Degree 2 (as defined in IEC61010-1). Rated for indoor use only. 1- 18 MTM400A Specifications and Performance Verification...

  • Page 31: Table 1- -31: Environmental Limits And Use Classification For Safety Certification Compliance 1

    Mains fuse is 3.15 A, 250 V, Fast; Not operator replaceable. Refer servicing to qualified service personnel. Current Rating 1 Amp Pollution Degree Pollution Degree 2 (as defined in IEC 61010-1) Note: Rated for indoor use only. 1- 19 MTM400A Specifications and Performance Verification...
  • Page 32 Specifications 1- 20 MTM400A Specifications and Performance Verification...
  • Page 33 Performance Verification...
  • Page 35 Requirements The MTM400A monitor must be connected to a network and have a valid IP address as described in the MTM400A Quick Start User Manual. The client PC must satisfy the requirements listed in Table 1- -1 on page 1- -1.
  • Page 36 8. Click Connect to start the connection process. 9. Read the End User License Agreement if it appears, and then click I Accept. 10. When the MTM400A monitor RUI opens, click Device in the button bar to display the Device Information view (see Figure 2- -1).

  • Page 37: Figure 2- 1: Mtm400A Monitor Rui Display

    Performance Verification Figure 2- 1: MTM400A monitor RUI display 2- 3 MTM400A Specifications and Performance Verification...
  • Page 38 Performance Verification 2- 4 MTM400A Specifications and Performance Verification...

Table of Contents