Readouts - Martin Professional MAC 2000 User Manual

If tracking mode movement is not satisfactory there are 2 parameters that can be adXusted. The first is
selected under
calculate intermediate positions at a steady rate. Begin by selecting the alternative,
if the intermediate positions stray significantly from the line of travel.
The second parameter is the number of position updates used to calculate speed. The level is adXustable
between - and -0 under
over which speed is calculated, making movement smoother but less responsive to sudden changes.
Experiment for best results.
Display
The display intensity Z
determines whether the display remains on or extinguishes two minutes after the last key-press. To flip the
display, press jUpk and jDownk simultaneously.
6amp
There are two settings that modify lamp control: Automatic Lamp On Z
When
! 3 1 0
is on, the lamp strikes automatically after the fixture is powered on. When
! 31 0
lamp strikes automatically when the fixture receives DMT data, and it extinguishes -5 minutes after DMT
data is lost.
When
! 3 1 0
from striking at once. The delay is determined by the fixture address.
If striking lamps from the controller, note that striking many lamps at once may cause a voltage drop large
enough to prevent lamps from striking or trip the main circuit breaker. Avoid this by programming a nlamp
ono se_uence that strikes lamps one at a time at 5 second intervals.
Power to the lamp can be turned off from the controller if DMT Lamp Off Z
Shutter dimming curves
Two dimming curves are available for the mechanical shutter system for adXusting intensity
→
Z
$ & # % " . 6 5
applies a linear algorithm to intensity adXustment, that results in even adXustment across the whole dimming
range. Note that this setting has no effect on the optional dimming wheel, that uses a logarithmic dimming
curve.
D!8 reset
The fixture can be reset from the controller if DMT reset Z
Custom settings
The custom configuration function allows you to save and recall three sets of fixture settings. The savable
settings are DMT mode, pan7tilt speed, pan7tilt inverse and swap, DMT lamp off and reset, display settings,
shortcuts, studio mode, automatic lamp on, effects feedback, tracking algorithm, and tracking samples.

Readouts

Note: The MP-2 Uploader provides commands to display the time, temperature, and version readouts on
the fixture control panel.
Time
→
. 0/ 1 ' . 2 &
Under each item is a resettable Z
accumulated hours7strikes since fabrication Z
press jUpk until it reads
→ →
$ & # % ' # ! 6 2 1 " &
→
$ & # % ' #! 6
[ setting controls display brightness. The display on7off setting Z
" . 0 '
is off, the lamp remains off until a nlamp ono command is received from the controller. When
is set to either or
1 0 8 2 9
[. The default, dimmer curve -, simulates the dimming of a tungsten lamp. Dimmer curve 2
provides readouts of fixture hours Z
# % & '
. ZThis may also be done remotely using the MP-2 Uploader.[
<
. The default, , is the best choice with controllers that
2 1 " ,
→
. Increasing the number of samples increases the distance
6 ! 3
, the automatic lamp strike timing is staggered to prevent all lamps
→
$ & # % " # & %
[, lamp hours Z
: # %
[ increment counter and a non-resettable counter for total
[. To reset an increment counter, display it and then
' 1 ' 3
, which is better
2 1 " 7
[ and DMT Lamp Off Z
! 3 1 0
is set to
! 3 1 0
[ is on.
" 3 1 /
[ is set to .
1 0
[, and lamp strikes Z
3 ; : #
[
" . % $
[.
" 3 1 /
, the
8 2 9
[.
3 ; % '