Preventing Auto-Rp Messages From Being Forwarded On Software: Example - Cisco XR12000 Series Configuration Manual

Preventing Auto-RP Messages from Being Forwarded on Software: Example

RP/0/0/CPU0:router(config)#
RP/0/0/CPU0:router(config-mcast-default-ipv4)#
RP/0/0/CPU0:router(config-mcast-default-ipv4)#
RP/0/0/CPU0:router(config-mcast-default-ipv4)#
RP/0/0/CPU0:router(config-mcast-default-ipv4)#
RP/0/0/CPU0:router(config-mcast-default-ipv4)#
RP/0/0/CPU0:router(config-mcast)#
RP/0/0/CPU0:router(config)#
RP/0/0/CPU0:router#
IP Multicast Forwarding Rates Source Address, Group Address HW Forwarding Rates: bps In/pps
In/bps Out/pps Out
(*,224.0.0.0/24)
bps_in /pps_in /bps_out /pps_out
N/A / N/A / N/A / N/A
(*,224.0.1.39)
bps_in /pps_in /bps_out /pps_out
N/A / N/A / N/A / N/A
(*,224.0.1.40)
bps_in /pps_in /bps_out /pps_out
N/A / N/A / N/A / N/A
(*,232.0.0.0/8)
bps_in /pps_in /bps_out /pps_out
N/A / N/A / N/A / N/A
(30.0.70.2,225.0.0.0)
bps_in /pps_in /bps_out /pps_out
22649 / 50 / 22951 / 50
(30.0.70.2,225.0.0.1)
bps_in /pps_in /bps_out /pps_out
22649 / 50 / 22951 / 50
(30.0.70.2,225.0.0.2)
bps_in /pps_in /bps_out /pps_out
22649 / 50 / 22951 / 50
(30.0.70.2,225.0.0.3)
bps_in /pps_in /bps_out /pps_out
22649 / 50 / 22951 / 50
(30.0.70.2,225.0.0.4)
bps_in /pps_in /bps_out /pps_out
22649 / 50 / 22951 / 50
(30.0.70.2,225.0.0.5)
bps_in /pps_in /bps_out /pps_out
22649 / 50 / 22951 / 50
(30.0.70.2,225.0.0.6)
bps_in /pps_in /bps_out /pps_out
Preventing Auto-RP Messages from Being Forwarded on Software: Example
This example shows that Auto-RP messages are prevented from being sent out of the Packet over SONET/SDH
(POS) interface 0/3/0/0. It also shows that access list 111 is used by the Auto-RP candidate and access list
222 is used by the boundary command to contain traffic on POS interface 0/3/0/0.
ipv4 access-list 111
10 permit 224.1.0.0 0.0.255.255 any
20 permit 224.2.0.0 0.0.255.255 any
!
Cisco IOS XR Multicast Configuration Guide for the Cisco XR12000 Series Router, Release 5.1.x
98
multicast-routing vrf vpn12 address-family ipv4
exit
exit
show mfib route rate
Implementing Multicast Routing on Cisco IOS XR Software
rate-per-route
interface all enable
accounting per-prefix
commit
exit
OL-30405-02