ABB COMMANDER 351 User Manual page 2

GETTING STARTED
Step 3 – Setting the Parameters (Fig. GS.1)
Power-up the instrument. Press the
A
seconds to advance directly to Level 6 – Basic Configuration.
Set the appropriate application template, output type and control action. Use the
B
advance between frames and upper
Section 4.2 for further information.
Note. When the output type has been selected, the available inputs and outputs default
to the settings shown in Table B on the rear fold-out.
If you are not using 4 to 20mA inputs, then select Level 7 using the upper
C
and set up Analog Inputs I/P1 to I/P3 to suit your process – see Section 4.3.
Controller templates only:
D
Select Level 2 using the upper and
• Analog or Motorized Valve Control – set the Proportional, Integral and
Derivative terms.
• Time Proportioning Control – set the Cycle Time, Hysteresis and P, I & D Terms
• Heat/Cool Outputs – set the points at which the Output 1 and Output 2
become active.
Press to return to the Operating displays.
E
Adjust the set point to the required value.
F
Your COMMANDER 350 is now in operation
A
LEV. 6 LEV. 7
351. 5
+
350. 0 APPL INPt
70
B
t. A PP
C
01. S L
O. t YP
ANLG
351. 5
350. 0
C. A Ct
70
rEV
FrEJ
50
Fig. GS.1 Setting the Parameters
and keys simultaneously and hold for 3
key to
and keys to adjust the default values – see
and keys
keys and set the tune parameters:
F
E
LEV2
351. 5
tUNE 350. 0
70
D
Note. With the above
configuration, no alarms or
limits have been set and
advanced functionality (gain
scheduling, set point
sources etc.) has not been
enabled.
ABB
The Company
We are an established world force in the design and manufacture of
instrumentation for industrial process control, flow measurement, gas
and liquid analysis and environmental applications.
As a part of ABB, a world leader in process automation technology, we
offer customers application expertise, service and support worldwide.
We are committed to teamwork, high quality manufacturing, advanced
technology and unrivalled service and support.
The quality, accuracy and performance of the Company's products
result from over 100 years experience, combined with a continuous
program of innovative design and development to incorporate the latest
technology.
The NAMAS Calibration Laboratory (No. 0255) is just one of ten flow
calibration plants operated by the Company, and is indicative of our
dedication to quality and accuracy.
Use of Instructions
Warning.
An instruction that draws attention to the risk of
injury or death.
Caution.
An instruction that draws attention to the risk of
damage to the product, process or surroundings.
Although Warning hazards are related to personal injury, and Caution hazards are associated with equipment or
property damage, it must be understood that operation of damaged equipment could, under certain operational
conditions, result in degraded process system performance leading to personal injury or death. Therefore, comply
fully with all Warning and Caution notices.
Information in this manual is intended only to assist our customers in the efficient operation of our equipment. Use
of this manual for any other purpose is specifically prohibited and its contents are not to be reproduced in full or part
without prior approval of the Marketing Communications Department.
Health and Safety
To ensure that our products are safe and without risk to health, the following points must be noted:
1. The relevant sections of these instructions must be read carefully before proceeding.
2. Warning labels on containers and packages must be observed.
3. Installation, operation, maintenance and servicing must only be carried out by suitably trained personnel
and in accordance with the information given.
4. Normal safety precautions must be taken to avoid the possibility of an accident occurring when operating
in conditions of high pressure and/or temperature.
5. Chemicals must be stored away from heat, protected from temperature extremes and powders kept dry.
Normal safe handling procedures must be used.
6. When disposing of chemicals ensure that no two chemicals are mixed.
Safety advice concerning the use of the equipment described in this manual or any relevant hazard data
sheets (where applicable) may be obtained from the Company address on the back cover, together with
servicing and spares information.
BS EN ISO 9001:2000
Cert. No. Q 05907
EN 29001 (ISO 9001)
Lenno, Italy – Cert. No. 9/90A
Stonehouse, U.K.
0255
Note.
Clarification of an instruction or additional
information.
Information.
Further reference for more detailed information
or technical details.