Page 1
PJC211/212/221/222 S-link Control Panel SIDE-POWER Thruster Systems Installation and user's manual v 2.0.2 SLEIPNER MOTOR AS P.O. Box 519 N-1612 Fredrikstad Norway Tel: +47 69 30 00 60 w w w . s i d e - p o w e r . c o m...
DO NOT connect any other control equipment to the S-link controlled products except Side-Power original S-link products or via a Side-Power supplied interface product made for interfacing with other controls. Any attempt to directly control or at all connect into...
• Plug & play cables with compact connectors • Diagnostics and system setup via panel • Built-in audible alarm “buzzer” • Connector for external “buzzer”/loud audible alarms • Supports Side-Power retractable thrusters with or without Speed Control PJC211/212/221/222 2.0.2 - 2013...
MENU or mute internal alarm buzzer Press to change Press and hold for 3 between day and seconds to access night light menu system and choose items in menus PJC211/212/221/222 2.0.2 - 2013...
3 seconds to activate control panel or cancel or STOP control panel. go back in menu system Press to change Emergency stop between day and button night light. Press and hold for 3 seconds to enter menu system PJC211/212/221/222 2.0.2 - 2013...
DC here in a single DC electric stern electric stern thruster setup thruster setup. Examples of display for different panel applications PJC211/221: PJC221: PJC221: DC Electric Bow thruster Hydraulic Bow thruster AC Electric Bow thruster...
Page 7
FIRST TIME SETUP After installation of a S-link thrusters system, a System Setup procedure to setup control panels, thrusters and additional equipment must be completed (ref. procedure on page 10) before the system can be used. PJC211/212/221/222 2.0.2 - 2013...
C for PPC800 FW V1.013 or older/ SR150000 FW V1.006 or older): Continuous beeps, and the “HOLD” function will be cancelled and both thrusters will stop. Temperature must drop below 115 C (100 C for PPC800 FW V1.013 or older) before the thruster can be operated again. PJC211/212/221/222 2.0.2 - 2013...
Page 9
WARNING! HIGH SPEED. STABILIZER NOT ACTIVE! (Only for yachts equipped with a Side-Power Stabilizer system) Warning will show when yacht is driven at high speed with stabilizer system inac- tive. Please refer to the Stabilizer ECU manual for speed settings.
Go through all devices and make sure that they are set to the correct instance and function (refer to detailed instructions in the SETUP section of “Menu System”-chapter). Press button below the -symbol to save setting and return to “Setup”- Menu. PJC211/212/221/222 2.0.2 - 2013...
A star (*) on each side indicated the laguage set. STABILIZER (Shown only for yachts equipped with a Side-Power Stabilizer system) Press the button below to edit the selected parameter. STABILIZER ON/OFF will start to blink, use joystick to alter value.
Page 12
After 15 minutes the second pump will be deactivated unless the pressure is still below 80 bar. NB: “Pump Control: Power Save” must only be used on PHC 024 with firmware V.1.008 or newer! PJC211/212/221/222 2.0.2 - 2013...
Page 13
Set the location for selected device. Use BOW or STERN in a conven- tional thruster system. In a system with two bow or stern thrusters (i.e a catamaran), use BOW or STERN for port thruster, BOW-STB or STERN-STB for starboard thruster PJC211/212/221/222 2.0.2 - 2013...
Page 14
SRHP: Proportional Hydraulic retract. This needs the PHC024 controller. SRVP 80/100: Retract SR150000 with PPC800, both devices needs to be set to SRVP 80/100. PPC800 SR150000 SR61242 PHC 024 SR(V) ON/OFF SRP 80/100 SRVP 130-210 SEP 30-240 SRVP 80/100 SRHP PJC211/212/221/222 2.0.2 - 2013...
Page 15
One step on the Hold-button represents 1/6 if the calibrated value. Adjust power with the joystick. Press the button below to save the calibration values. Press the button below to cancel calibration without saving. PJC211/212/221/222 2.0.2 - 2013...
Page 16
Display info about the control panel FW: Version number, Firmware HW: Version number, Hardware S/N: Serial number of the control panel Voltage: S-link system voltage measured at the panel Press the button below to return to the previous menu. PJC211/212/221/222 2.0.2 - 2013...
Set the time from last use to auto panel shutdown. Set from 1-60 minutes in 5 minute steps (1 minute steps from 1 to 5 minutes) or OFF (panel will not turn off automatically) UNIT TEMPERATURE Values: CELSIUS, FAHRENHEIT Set the panel temperature displaying unit PJC211/212/221/222 2.0.2 - 2013...
Page 22
Connections for optional external buzzer/audible alarm External alarm/buzzer connection (S-link) Supply +12V / 24V DC Internal fuse/relay External alarm buzzer 12V / 24V DC - max 0,5A PJC211/212/221/222 2.0.2 - 2013...
Page 23
Fill in the type, location and serial numbers of the S-link devices installed. Keeping this as a reference will make the setup procedure easier! S-link device Location Serial number (ie Thruster, AMS, PPC800 etc) (Bow, Bow-STB, Stern, Stern-STB) PJC211/212/221/222 2.0.2 - 2013...
SIDE-POWER SERVICE CENTRES Argentina Estonia/Latvia/Lithuania Japan Spain Trimer SA Miltec Systems OÜ Turtle Marine Inc. Imnasa Marine Products Buenos Aires Tallin Nagasaki Girona Tel:+54 11 4580 0444 Tel: +372 5013997 Tel:+81 95 840 7977 Tel:+34 902 300 214 Fax:+54 11 4580 0440...
Need help?
Do you have a question about the PJC211 and is the answer not in the manual?
Questions and answers