Qx82 Dc Input Module (Negative Common Type) - Mitsubishi Electric QX10 User Manual

2 INPUT MODULE SPECIFICATIONS

2.14 QX82 DC Input Module (Negative Common Type)

Specifications
Number of input points
Isolation method
Rated input voltage
Rated input current
Input derating
ON voltage/ON current
OFF voltage/OFF current
Input impedance
OFF to ON
Response
time
ON to OFF
Dielectric withstand voltage
Insulation resistance
Noise immunity
Protection of degree
Common terminal arrangement
Number of I/O points
Operation indicator
External connections
Applicable wire size
External wiring connector
Applicable connector/terminal block
conversion module
5VDC internal current consumption
Weight
Derating Chart
(%)
100
90
80
ON
70
ratio
60
50
40
30
20
0 10 20 30
Ambient temperature
External Connections
1B20
R
R
Left side
1A5
(first half)
1B2
Right side
24VDC
(latter half)
1B1
The above diagram shows the first half of 32 points
(F).
The latter half of 32 points (L) are similar.
1: For the setting method, refer to the section 1.3.1.
2: Pin number of 1
side connector.
3: Selection of left-hand (F) side provides the first half (X00 to X1F) LED indications, and selection of right-hand (L) side provides the
latter half (X20 to X3F) LED indications.
4 : When using A6CON2 or A6CON3, refer to Chapter 7.
2 - 16
Type
24VDC (+20/-15%, ripple ratio within 5%)
1ms/5ms/10ms/20ms/70ms or less (CPU parameter setting)
1ms/5ms/10ms/20ms/70ms or less (CPU parameter setting)
560VAC rms/3 cycles (altitude 2000m (6557.38ft.))
10M
By noise simulator of 500Vp-p noise voltage, 1
and 25 to 60Hz noise frequency
First transient noise IEC61000-4-4: 1kV
32 points/common (common terminal: 1B01, 1B02, 2B01, 2B02)
64 (I/O allocation is set as a 32-points input module)
ON indication (LED), 32 point switch-over using switch
0.3mm
A6CON1, A6CON2, A6CON3, A6CON4 (optional)
24VDC
B20
B19
26.4VDC
B18
B17
28.8VDC
B16
B15
B14
40 50 55 ( C )
B13
B12
B11
B10
B9
B8
B7
B6
Internal
B5
circuit
B4
LED
B3
B2
SW
B1
Indication
selector
3
circuit
Module front view
indicates that of the left-hand side connector, and pin number of 2
DC Input Module (Negative Common Type)
QX82
64 points
Photocoupler
Approx. 4mA
Refer to the derating chart.
19V or higher/3mA or higher
11V or lower/1.7mA or lower
Approx. 5.6k
Initial setting is 10ms.
Initial setting is 10ms.
or more by insulation resistance tester
IP2X
40-pin connector
2
(For A6CON1 or A6CON4) 4
—————
90mA (TYP. all points ON)
0.18kg
Sig-
Pin
Pin-Outs nal
No.
No.
1B20 X00
1B19 X01
1B18 X02
1B17 X03
A20
1B16 X04
A19
A18
1B15 X05
A17
A16
1B14 X06
A15
1B13 X07
A14
A13
1B12 X08
A12
A11
1B11 X09
A10
A9
1B10 X0A
A8
A7 1B09 X0B
A6
1B08 X0C
A5
A4
1B07 X0D
A3
A2
1B06 X0E
A1
1B05 X0F
1B04 Vacant
1B03 Vacant
1B02 COM
1B01 COM
MELSEC-Q
Appearance
QX82
0 1 2 3 4 5 6 7
8 9 A B C D E F
0 1 2 3 4 5 6 7
8 9 A B C D E F
24VDC
4mA
1
1
s noise width
Sig- Sig-
Pin Pin
nal nal
No. No.
No. No.
1A20 X10 2B20 X20
1A19 X11 2B19 X21
1A18 X12 2B18 X22
1A17 X13 2B17 X23
1A16 X14 2B16 X24
1A15 X15 2B15 X25
1A14 X16 2B14 X26
1A13 X17 2B13 X27
1A12 X18 2B12 X28
1A11 X19 2B11 X29
1A10 X1A 2B10 X2A
1A09 X1B 2B09 X2B
1A08 X1C 2B08 X2C
1A07 X1D 2B07 X2D
1A06 X1E 2B06 X2E
1A05 X1F 2B05 X2F
1A04 Vacant 2B04 Vacant
1A03 Vacant 2B03 Vacant
1A02 Vacant 2B02
COM2
1A01 Vacant 2B01
COM2
indicates that of the right-hand
QX82
DISPLAY
F L
Sig-
Pin
nal
No.
No.
2A20 X30
2A19 X31
2A18 X32
2A17 X33
2A16 X34
2A15 X35
2A14 X36
2A13 X37
2A12 X38
2A11 X39
2A10 X3A
2A09 X3B
2A08 X3C
2A07 X3D
2A06 X3E
2A05 X3F
2A04 Vacant
2A03 Vacant
2A02 Vacant
2A01 Vacant
2 - 16