Qx72 Dc Input Module (Positive Common/Negative Common Shared Type) - Mitsubishi Electric QX10 User Manual

2 INPUT MODULE SPECIFICATIONS

2.11 QX72 DC Input Module (Positive Common/Negative Common Shared Type)

Specifications
Number of input points
Insulation method
Rated input voltage
Rated input current
Input derating
ON voltage/ON current
OFF voltage/OFF current
Input resistance
OFF ON
Response
time
ON OFF
Dielectric maximum voltage
Insulation resistance
Noise immunity
Protection of degree
Common terminal arrangement
Number of I/O points
Operation indicator
External connections
Applicable wire size
External wiring connector
5VDC internal current consumption
Weight
External Connections
For open collector (positive common) connection
1B20
R
Left side
(first half)
Right side
(latter half)
1B02
1B01
5/12VDC
For TTL, LS-TTL, CMOS buffer
(positive common) connections
1B20
1B02
The above diagram shows the first half of
32 points (F).
The latter half of 32 points (L) are similar.
1: For the setting method, refer to the section 1.3.1.
2: Pin number of 1
side connector.
3: Selection of left-hand (F) side provides the first half (X00 to X1F) LED indications, and selection of right-hand (L) side provides the
latter half (X20 to X3F) LED indications.
4: When using A6CON2 or A6CON3, refer to Chapter 7.
2 - 13
Type DC Input Module (Positive Common/Negative Common Shared Type)
5VDC
(+20/-15%, ripple ratio within
5%)
Approx. 1.2mA
1ms/5ms/10ms/20ms/70ms or less (CPU parameter setting) 1
1ms/5ms/10ms/20ms/70ms or less (CPU parameter setting) 1
560VAC rms/3 cycles (altitude 2000m)
10M
By noise simulator of 500Vp-p noise voltage,
1 s noise width and 25 to 60Hz noise frequency
First transient noise IEC61000-4-4: 0.25kV
32 points/common (common terminal: 1B01, 1B02, 2B01, 2B02)
64 (I/O allocation is set as a 64-points input module)
ON indication (LED), 32-point switchover using switch
0.3mm
A6CON1, A6CON2, A6CON3, A6CON4 (optional)
Pin-Outs
LED
B20
Internal
B19
circuit
B18
B17
B16
3
LED
B15
SW
Indication
B14
selector
B13
circuit
B12
B11
B10
B9
B8
For sensor
B7
(negative common)
B6
connections
B5
1B20
B4
B3
B2
B1
1B02
Module
front view
indicates that of the left-hand side connector, and pin number of 2
QX72
64 points
Photocoupler
(+20/-15%, ripple ratio within 5%)
Approx. 3.3mA
None
3.5V or higher/3mA or higher
1V or lower/0.1mA or lower
Approx. 3.3k
Initial setting is 10ms
Initial setting is 10ms
or more by insulation resistance tester
IP2X
40-pin connector
2
(For A6CON1 or A6CON4) 4
85mA (TYP, all points ON)
0.13kg
Signal
Pin No.
No.
1B20 X00
1B19 X01
A20
1B18 X02
A19
1B17 X03
A18
A17
1B16 X04
A16
1B15 X05
A15
A14
1B14 X06
A13
1B13 X07
A12
A11
1B12 X08
A10
1B11 X09
A9
A8
1B10 X0A
A7
1B09 X0B
A6
A5
1B08 X0C
A4
1B07 X0D
A3
A2
1B06 X0E
A1
1B05 X0F
1B04 Vacant
1B03 Vacant
1B02 COM1
1B01 COM1
12VDC
Signal Signal
Pin No. Pin No.
No.
1A20 X10 2B20
1A19 X11 2B19
1A18 X12 2B18
1A17 X13 2B17
1A16 X14 2B16
1A15 X15 2B15
1A14 X16 2B14
1A13 X17 2B13
1A12 X18 2B12
1A11 X19 2B11
1A10 X1A 2B10
1A09 X1B 2B09
1A08 X1C 2B08
1A07 X1D 2B07
1A06 X1E 2B06
1A05 X1F 2B05
1A04 Vacant 2B04 Vacant
1A03 Vacant 2B03 Vacant
1A02 Vacant 2B02 COM2
1A01 Vacant 2B01 COM2
indicates that of the right-hand
MELSEC-Q
Appearance
QX72
0 1 2 3 4 5 6 7
8 9 A B C D E F
0 1 2 3 4 5 6 7
8 9 A B C D E F
QX72
DISPLAY
5/12VDC
F L
1.2/3.3mA
Signal
Pin No.
No. No.
X20 2A20 X30
X21 2A19 X31
X22 2A18 X32
X23 2A17 X33
X24 2A16 X34
X25 2A15 X35
X26 2A14 X36
X27 2A13 X37
X28 2A12 X38
X29 2A11 X39
X2A 2A10 X3A
X2B 2A09 X3B
X2C 2A08 X3C
X2D 2A07 X3D
X2E 2A06 X3E
X2F 2A05 X3F
2A04 Vacant
2A03 Vacant
2A02 Vacant
2A01 Vacant
2 - 13