Qy42P Transistor Output Module (Sink Type) - Mitsubishi Electric QX10 User Manual

3 OUTPUT MODULE SPECIFICATIONS

3.6 QY42P Transistor Output Module (Sink Type)

Specifications
Number of output points
Isolation method
Rated load voltage
Maximum load current
Maximum inrush current
Leakage current at OFF
Maximum voltage drop at ON
OFF to ON
Response time
ON to OFF
Surge suppressor
Fuse
External supply Voltage
power
Current
Dielectric withstand voltage
Insulation resistance
Noise immunity
Protection of degree
Common terminal arrangement
Number of I/O points
Protection function
Operation indicator
External connections
Applicable wire size
External wiring connector
Applicable connector/terminal
block conversion module
5VDC internal current
consumption
Weight
External Connections
Internal
circuit
LED
Left side
(first half)
Indication
selector
SW
circuit
Right side
(latter half)
2
The above diagram shows the first half of 32 points
(F).
The latter half of 32 points (L) are similar.
1: Pin number of 1
side connector.
2: Selection of left-hand (F) side provides the first half (Y00 to Y1F) LED indications, and selection of right-hand (L) side provides the
latter half (Y20 to Y3F) LED indications.
3: When using A6CON2 or A6CON3, refer to Chapter 7.
3 - 6
Type
0.1VDC (TYP.) 0.1A, 0.2VDC (MAX.) 0.1A
1ms or less (rated load, resistive load)
12-24VDC (+20/-15%) (ripple ratio within 5%)
560VAC rms/3 cycles (altitude 2000m (6557.38ft.))
10M
By noise simulator of 500Vp-p noise voltage, 1
First transient noise IEC61000-4-4: 1kV
32 points/common (common terminal: 1A01, 1A02, 2A01, 2A02)
64 (I/O allocation is set as a 64-points output module)
Yes (thermal protection, short circuit protection)
• Thermal protection is activated in increments of 1 point.
• Short circuit protection is activated in increments of 1 point.
ON indication (LED), 32 point switch-over using switch
0.3mm
A6CON1, A6CON2, A6CON3, A6CON4 (optional)
B20
L
R
A05
L
B01,B02
A01,A02
12/24VDC
Module front view
indicates that of the left-hand side connector, and pin number of 2
Transistor Output Module (Sink Type)
QY42P
64 points
Photocoupler
12-24VDC (+20/-15%)
0.1A/point, 2A/common
0.7A, 10ms or less
0.1mA or less
1ms or less
Zener diode
No
20mA (at 24VDC)/common
or more by insulation resistance tester
and 25 to 60Hz noise frequency
IP2X
40-pin connector
2
(For A6CON1 or A6CON4) 3
A6TBXY36, A6TBXY54
150mA (TYP. all points ON)
0.17kg
Pin
Pin-Outs
No.
1B20
1B19
B20 A20 1B18
B19 A19
1B17
B18 A18
1B16
B17 A17
1B15
B16 A16
1B14
B15 A15
B14 A14
1B13
B13 A13
1B12
B12 A12
1B11
B11 A11
1B10
B10 A10
B9 A9
1B09
B8 A8
1B08
B7 A7
1B07
B6 A6
1B06
B5 A5
B4 A4 1B05
B3 A3
1B04 Vacant
B2 A2
1B03 Vacant
B1 A1
1B02
1B01
s noise width
Sig- Sig-
Pin Pin
nal nal
No. No.
No. No.
Y00 1A20 Y10 2B20
Y01 1A19 Y11 2B19
Y02 1A18 Y12 2B18
Y03 1A17 Y13 2B17
Y04 1A16 Y14 2B16
Y05 1A15 Y15 2B15
Y06 1A14 Y16 2B14
Y07 1A13 Y17 2B13
Y08 1A12 Y18 2B12
Y09 1A11 Y19 2B11
Y0A 1A10 Y1A 2B10
Y0B 1A09 Y1B 2B09
Y0C 1A08 Y1C 2B08
Y0D 1A07 Y1D 2B07
Y0E 1A06 Y1E 2B06
Y0F 1A05 Y1F 2B05
1A04 Vacant 2B04
1A03 Vacant 2B03
12/24
1A02 2B02
COM1
VDC
12/24
1A01 2B01
COM1
VDC
indicates that of the right-hand
MELSEC-Q
Appearance
QY42P
0 1 2 3 4 5 6 7
8 9 A B C D E F
0 1 2 3 4 5 6 7
8 9 A B C D E F
QY42P
DISPLAY
12/24VDC
F L
0.1A
Sig- Sig-
Pin
nal nal
No.
No. No.
Y20 2A20 Y30
Y21 2A19 Y31
Y22 2A18 Y32
Y23 2A17 Y33
Y24 2A16 Y34
Y25 2A15 Y35
Y26 2A14 Y36
Y27 2A13 Y37
Y28 2A12 Y38
Y29 2A11 Y39
Y2A 2A10 Y3A
Y2B 2A09 Y3B
Y2C 2A08 Y3C
Y2D 2A07 Y3D
Y2E 2A06 Y3E
Y2F 2A05 Y3F
Vacant 2A04 Vacant
Vacant 2A03 Vacant
12/24
2A02
COM2
VDC
12/24
2A01
COM2
VDC
3 - 6