Pioneer VSA-AX10 Operating Instructions Manual page 61

Preset Recall
[ DVD/LD ]
AMP
SELECT MAKER
ITEM
DVD/LD
PIONEER TOSHIBA SHARP
DVD
VCR1
/DVR PANA-
SONY
SONIC
MAKER
VCR2
PIONEER AKAI DENON
VICTOR
VCR3
PAGE
TV 1 / 2
5
6
Preset Recall
[ DVD/LD ]
AMP
SELECT NUMBER
ITEM
DVD
DVD/LD
1 2
VCR1 MAKER
/DVR
PIONEER
VCR2
VCR3
NUMBER
SETUP
1
TV
«
Preset Recall
AMP
DVD/LD
VCR1
/DVR
SELECT FUNCTION
VCR2
VCR3
TV
Remote Control of Other Components
5 Select the name of the company that
BACK REMOTE
SETUP
makes your component.
CD
If there are two pages of company names, use the page
CD-R/
TAPE1
+/– buttons to go back and forth between the two sets
TUNER
SAM-
of makers' names. For explanation purposes, we'll use
SUNG
VIDEO
PIONEER as an example.
SAT
TV
6 Press the number 1 button.
CONTROL
If the component you are trying to control turns on/off,
the setup for this component is complete, but compo-
nents that don't have a standby mode can't respond in
this way. To test if you've set it up properly work through
step 8. Then try using selecting the function you just
setup (for example a CD player) and using the controls
on this remote control. If the component does not
respond, try working through the procedure again and
pressing number 2 instead this time. Continue this
procedure until one of the commands works.
BACK REMOTE
SETUP
If none of the commands seem to work, try the learning
CD
mode to program the component into the remote
CD-R/
control. This is explained on the following page.
TAPE1
TUNER
To go back a screen
VIDEO
press the BACK button.
SAT
To exit the process without inputting the commands
TV
OK
CONTROL
press the BACK button repeatedly.
7 Press the SETUP OK button and the
7
screen returns to SELECT FUNCTION
so you can program another
component into the remote control.
9
Naturally it's easiest and most logical to assign the
button that has the same name as the component you
are setting up (for example, choose the DVD/LD button
for your DVD player).
You may find you have components which do not
BACK REMOTE
SETUP
correspond to the name on any MULTI CONTROL button
CD
(for example a cable TV tuner) or you have two compo-
CD-R/
TAPE1 nents where only one button is provided (for example,
CD-R/TAPE 1). In this case, use step 3 to assign any
TUNER
available MULTI CONTROL button to the component you
VIDEO
want to remote control.
SAT
For example, you may have both a CD-R and a tape deck
TV
CONTROL in your system but only one video deck. It would make
sense to assign the CD-R/TAPE 1 MULTI CONTROL
button to the CD-R and the VCR 2 MULTI CONTROL
button to your tape deck. To do this choose VCR 2 in
step 3 when you want to set up the tape deck. Then
choose TAPE in step 4 and proceed as above. The only
practical difference in this method is that you have to
remember the VCR 2 MULTI CONTROL button is actually
your tape deck.
In this case, you would need to hook up your tape deck
to the input jacks marked VCR 2 on the back of the
amplifier.
This method should help you customize the remote
control for your system and let you control all of your
components with the remote control for the VSA-AX10.
8 Repeat the process from step 2 for all
of your components.
9 Press the BACK button repeatedly to
leave the REMOTE SETUP mode.
61
En