Brita Tap – Easy Installation; Selecting Appropriate Setting On The Filter Head; Commissioning; Cartridge Setting - Brita WD3030 Manual

8. Hose (4), length = 800 mm and 1/2" female nut on one end and
3/8" female nut at other end – for connection between cold
water connection point and the inlet side of the fi lter head (1/2"
& 3/8" washers included in washer pack
9. Usage instructions
10. Pressure Limiting Valve with back-fl ow prevention
11. T-piece
12. Washers
13. Isolating Valve
14. Adapter 1/4" - 1/2"
Recommended tools for installation: one Allen hexagonal key
(4 mm), a pipe wrench, adjustable spanner for different sizes.
Recommended for installation of the wall mount bracket: two
screws (e.g. 5 mm in size) and two wall plugs (if necessary).
Please use appropriate screws and wall plugs for the type of wall in
the under-sink compartment.
3 BRITA Tap – easy installation
Installation of the fi lter system must comply with the relevant
state or local plumbing regulations and standards (AS/NZS
3500). The pressure limiting valve must be installed as directed
to comply and protect your tap from possible pressure surges.
Depending on the necessary method of connection to the cold
!
water supply, additional valves/adaptors/components may
be required, and the services of a licensed plumber may be
necessary. If you do not have an available connection to the
cold water supply and it is necessary to cut into the cold water
supply line, a licensed plumber is required.
Before starting, please check that you have all the components as
listed above (see fi g. 1) as well as the recommended tools.
There are 7 steps to the installation.
Prior to installation, read the Technical Data (chapter 8) and
the Operation and Safety Information. (After storage and
transport below 0°C, the product must be stored in the open
!
original packaging for at least 24 hours at the stated ambient
temperatures (chapter 8) for operation.) The system cannot
be installed with a low pressure boiler.
1014663-001_GA_BRITA_Tap_AU.indb 5 1014663-001_GA_BRITA_Tap_AU.indb 5
3.1 Step 1: Selecting appropriate setting on the
fi lter head
The fi lter head is set to "B" by default. For use with the supplied
A 1000 fi lter cartridge you need to change the setting in the win-
dow to "0". Use an Allen key (hexagonal socket wrench) and turn
the hexagonal nut in the direction of the arrow in the window until
the "0" appears. Refer fi g. 2)
3.2 Step 2: Starting the BRITA Tap Cartridge
Status Indicator
The BRITA Tap Cartridge Status Indicator reminds you through
three different coloured fl ashing lights when to exchange the fi lter
cartridge.
A Commissioning:
Insert the enclosed battery (1x CR2032) into the appropriate
compartment of the BRITA Tap Cartridge Status Indicator. Note
the print on the battery for correct implementation (fi g. 3). All LEDs
should fl ash shortly. Close the compartment. Keep the Reset but-
ton pushed for three seconds until a small green light fl ashes three
times at the top (fi g. 4).
B Initial programming of the BRITA Tap Cartridge
Status Indicator:
Please programm the BRITA Tap Cartridge Status Indicator as
follows (see fi g. 4):
a Cartridge Setting
Push the button on the left side (CARTRIDGE) to set the cartridge
you are using. If you push the button one time, two yellow LEDs
will fl ash (default cartridge setting: P 1000). To set the supplied
fi lter cartridge A 1000, push the button, until one yellow LED fl ashes.
Note: In Australia and New Zealand BRITA Tap is not compatible
with fi lter cartridges P 1000 and P 3000.
(fi g. 2)
5
ENGLISH
28.04.15 15:25 28.04.15 15:25