Table of Contents
Advertisement
Veo17 Embedded DVR
7. LOGIN INFORMATION
Local Login: On startup the local log in screen will be displayed. Using the monitor and
mouse connected to the DVR use the on screen keyboard to log in.
Default login and password are i3admin / i3admin.
Remote Login: It is possible to use a networked computer to remotely access the Veo17.
To do so open the browser on the networked computer and enter the IP address of the
Veo17 machine into the address window. A login window will appear, enter the username
and password.
Default IP: 192.0.0.16
Default Username and Password: i3admin / i3admin
Input Method
The Veo17 does not support an external keyboard. In order to enter login information or
any other text input required into the machine there is a soft keyboard that will pop up as
soon as you click on an input box.
Use the supplied mouse to select the required letters and numbers for all input that
requires text.
8. Starting Up and Shutting Down
Proper startup and shutdown procedures are crucial to expanding the life of the Veo17.
Starting up the Veo17
Check that the voltage of the extra power supply is the same with the Veo17's
requirements, and the ground connection is working properly.
1. Check that the power supply is plugged into an electrical outlet. It is HIGHLY
recommended that an Uninterrupted Power Supply (UPS) be used in conjunction with
the device.
2. Turn on the power switch on the rear panel. The Power indicator LED should turn on
indicating that the unit has begun to start up.
3. Once it has started the Power indicator will remain lit.
Shutting down the Veo17
1. Enter the Setup menu by right clicking on the Live View Mode and selecting Setup from
the menu. Then select Shutdown from the Setup menu.
2. From this window the user can select between Logout, Shutdown, or Reboot for the
machine. Select the Shutdown option.
3. Click the Yes button if you are sure and wait for the message that it is safe to turn the
power off on the machine by flipping the power switch on the back of the machine.
4. To logout or reboot the machine select those options from the shutdown menu.
9. SET UP WIZARD AND FIRST LOG IN
On the first login the setup wizard will open to allow for some quick configuration. The
second window to open will ask if the Wizard should open on every restart of the DVR.
Deselect this box to not see the Wizard again. You will be prompted to set The language
(note that only English is available), Reset the Admin Password, Time Zone, Date Format,
System Date and System Time, Network settings, Initialize the Storage Drive, and to set
basic recording parameters for the channels (Continuous or Motion detection).
All of these settings can be found under the setup menu described below in any changes
are needed. It is possible to cancel out of the Wizard at any time during the process.
10. Live View
The live view is the live display from each camera in real time. The DVR will automatically
enter Live View mode when powered on.
Live View Icons
In the Live View there are icons in the right top of the screen for each channel, showing
the status of the record and alarm in the channel, so that you can know whether the
channel is recorded, or when an alarm occurs as soon as possible. A red "REC" will
appear when the channel is recording and with a red Bell if the
recording is triggered by motion or alarm.
Quick Setting Toolbar in Live View Mode
On the screen of each channel there is a quick setting toolbar which appears on a single
left click with the mouse either in Multi View or on a single camera full screen view.
Instant Search: Shows the recorded data from the selected channel for the last
five minutes. If no record is found, it means there was no recording during the last
five minutes.
Audio On/Off: Turns the Audio on or off on the channel. Only Channel 1 has the
Audio feature.
PTZ: Pan Tilt Zoom provides PTZ controls for PTZ cameras. This will open a new
window to control and set the PTZ camera. See below for instruction for using the
PTZ functions.
Digital Zoom: This will open the selected channel in its own window and provide
a movable box to zoom in on a particular part of the screen. Click the area within
the miniature box in the bottom right corner of the screen to move the Red Digital
Zoom frame to centre on the area. Works in both Live and Search modes.
Image Settings: This icon will open a manual Image Settings window to adjust
the settings on the selected channel. Further details below.
Page 4
Veo17
Rev.
170119
Advertisement
Table of Contents
