Table of Contents
Advertisement
Veo17 Embedded DVR
Once the settings above are set correctly the PTZ controls
will operate.
• Use the circular control panel with the mouse to move
the PTZ camera as required. Use the Zoom in and Zoom
out, Focus and Iris controls to fine tune the image. The
Speed bar will control how fast the camera will respond
to the commands. Adjust it as required.
Setting PTZ Presets,
Please make sure that the presets, patrols and patterns are supported by the PTZ
protocols configured in the previous step. Note: The Veo17 does not currently support PTZ
patrols or patterns.
Customizing Presets:
Set a preset location for the PTZ camera to point to when an event takes place.
• Use the directional controls to position the PTZ camera to the location required for the
Preset. Configure the zoom and focus as these will be recorded in the preset.
• Enter a preset number in the preset text field (valid numbers include 1-227) and click
the Set button to link the location and view of the camera to the preset number.
• Repeat these steps to save more presets. Remember to use a different preset number
for each preset.
• Click the Clear button to clear the location information of the preset, or click the Clear
All button to clear the location information of all the presets.
Calling Presets:
This feature calls the presets created in the previous step.
• On the PTZ setting interface click the PTZ button in the
lower right of the page. This will open the PTZ Channel
in full screen with a floating PTZ window. This window
has the PTZ controls on it. Click the Advanced button.
• Choose the Channel from the Channel drop down list.
• Enter the Preset number in the text field next to the
Call Preset button.
• Click the Call Preset button to call the preset.
• Click the Settings button at the bottom to return to the
main PTZ page to create a Preset to use in this step.
Accessing i3 Camera OSD With PTZ Menu
If you are using i3International cameras the AM42R and AM52R HD Analog Cameras with
the Veo17 it is possible to access the Camera's onboard software settings through the
Veo17's PTZ menu.
• Select the required channel from the Channel No. Drop Down box.
• Click the PTZ Settings button and set the PTZ protocol setting to i3-HDA(Coaxitron)
(this should be the last entry in the drop down list) and click the OK button.
• Using the PTZ control panel click the Iris+ button and hold it for just a moment. This
will open the camera's OSD on the screen. It is recommended to open the channel on
full screen to better read the menu.
• Use the up/down/right/left arrows on the PTZ control to navigate through the camera
menu. Click the Iris+ button to make a selection.
Motion:
Configure each channel for motion detection and define the area of the field of view of the
camera to detect motion.
• Select the channel to configure from the Channel No. drop down list.
• Check the Enable Motion Detection check box.
• Use the mouse to drag a box to define the areas that will be configured for motion
detection. Any area of the screen covered by the red grid will be configured for motion
detection. If you click the "Draw All" button the whole view will be covered with the
grid and boxes drawn in the screen will remove areas from the red grid thus removing
them from the configured area. Clicking the "Clear" button will remove the red grid
from the view and allow the addition of the grid by drawing boxes to create motion
detection areas.
• "Settings" Button will open a
window to provide a chance to
add additional channel to begin
recording when the previously
selected channel detects motion.
Also the Active Time for the motion
detection can be set. Click the
"Active Time" and define by setting
the hour and minutes of the day.
The "Linkage Method" defines how
the system reacts to motion being
detected. Choose 1, 2 or all 3 from
Full Screen Monitoring, Audible warning and Send Email. Instructions for configuring
an email will be listed below.
• Click the "Copy" button to copy the settings to multiple channels. A window will open
allowing the selection of which channels to configure with the current settings.
• Click the "Apply" button to save the changes made to the channel configuration.
• Click "Back" button to return to the Setup Menu.
Privacy Mask:
Set up to 4 areas for a privacy masks in the camera field of view.
Page 12
Veo17
Rev.
170119
Advertisement
Table of Contents
