KEB COMBIVERT F5 Safety Manual
Drive
Hide thumbs
Also See for COMBIVERT F5:
- Applications manual (378 pages) ,
- Reference manual (349 pages) ,
- Instruction manual (196 pages)
Related Manuals for KEB COMBIVERT F5
Summary of Contents for KEB COMBIVERT F5
- Page 1 COMBIVERT F5 SAFETY MANUAL | GENERAL SAFETY INSTRUCTIONS Translation of the original instructions Document 20157737 EN 00...
-
Page 3: Preface
PREFACE Preface The described hard- and software are developments of the KEB Automation KG. The enclosed documents correspond to conditions valid at printing. Misprint, mistakes and technical changes reserved. Signal words and symbols Certain operations can cause hazards during the installation, operation or thereafter. -
Page 4: Laws And Guidelines
Copyright The customer may use the instruction manual as well as further documents or parts from it for internal purposes. Copyrights are with KEB Automation KG and remain valid in its entirety. Other wordmarks or/and logos are trademarks (™) or registered trademarks (®) of their... -
Page 5: Table Of Contents
TAbLE OF CONTENTS Table of Contents Preface ..............................3 Signal words and symbols ......................3 More symbols ..........................3 Laws and guidelines ........................4 Warranty ............................4 Support ............................4 Copyright ............................4 Table of Contents ........................... 5 1 basic Safety Instructions ..........6 1.1 Target group ............................. -
Page 6: Basic Safety Instructions
Technical data and information for connection conditions shall be taken from the type plate and from the instruction manual and must be strictly observed. The used semiconductors and components of the KEB Automation KG are developed and dimensioned for the use in industrial products. -
Page 7: Residual Risks
The operation of our products outside the indicated limit values of the technical data leads to the loss of any liability claims. If the KEB COMBIVERT F5 is used in machines, which work under exceptional condi- tions or if essential functions, life-supporting measures or an extraordinary safety step must be fulfilled, the necessary reliability and security must be ensured by the machine builder. -
Page 8: Installation
bASIC SAFETY INSTRUCTIONS 1.4 Installation DANGER Do not operate in an explosive environment! ► The COMBIVERT is not intended for the use in potentially explosive environment. CAUTION Maximum design edges and high weight! Contusions and bruises! ► Never stand under suspended loads. ►... -
Page 9: Electrical Connection
bASIC SAFETY INSTRUCTIONS 1.5 Electrical connection DANGER Voltage at the terminals and in the device ! Danger to life due to electric shock ! ► Never work on the open device or never touch exposed parts. ► For any work on the unit switch off the supply voltage and secure it against switching on. -
Page 10: Emc-Confirm Installation
Accordng to EN 60204-1 it is permissible to disconnect already tested com- ponents. Drive converters of the KEB Automation KG are delivered ex works voltage tested to 100% according to product standard. 1.5.3 Insulation measurement An insulation measurement (in accordance with EN 60204-1 chapter 18.3) with 500 Vdc... -
Page 11: Start-Up And Operation
bASIC SAFETY INSTRUCTIONS 1.6 Start-up and operation The drive converter must not be started until it is determined that the installation com- plies with the machine directive; Account is to be taken of EN 60204-1. WARNING Software protection and programming ! Hazards caused by unintentional behavior of the drive! ►... -
Page 12: Maintenance
For applications that require cyclic switching on and off of the drive converter, a time of at least 5 min must have elapsed after the last switch-on.If you require shorter cycle times please contact KEB Automation KG. Short-circuit proof The drive converters are conditional short-circuit proof. After resetting the internal pro- tection devices, the function as directed is guaranteed. -
Page 13: Maintenance
1.9 Disposal Drive converters of the KEB Automation KG are professional, electronic devices exclu- sively for further industrial processing (so-called B2B devices). Thus the marking does not occur with the symbol of the crossed-out wheeled bin, but by the word mark and the date of manufacture. -
Page 14: Certification
The validity of the acceptance is only valid if the instructions given in the instruction manual are observed. 2.4 Further information and documentation You can find additional documentation for download at "www.keb.de" by entering the material number in the search field. Manuals - further parts of the instruction manual Drawings - various formats for 3-models (e.g. - Page 15 Tel: +55 16 31161294 E-Mail: roberto.arias@keb.de Room 1709, 415 Missy 2000 725 Su Seo Dong Gangnam Gu 135- 757 Seoul Republic of Korea Tel: +82 2 6253 6771 Fax: +82 2 6253 6770 E-Mail: vb.korea@keb.de Société Française KEB SASU France Z.I.