Table of Contents
Advertisement
About Multi-Effects Parameters
1: STEREO-EQ (Stereo equalizer)
This is a stereo equalizer which allows you to adjust the tone
quality using a low range, two mid-range, and a high range
control.
Lin---.;
4-Band EO
1----•
Lout
Rin---.;
4-Band EQ
i----,
Rout
LOW FREQ (low frequency) 200 Hz:/ 400 Hz:
Select the frequency (200 Hz/ 400 Hz) at which the low
frequency range will be adjusted.
LOW GAIN -15-+ 1 5 dB
Specify the low frequency gain (amount of boost or cut).
Positive(+) settings will emphasize (boost) the low range.
HIGH FREQ (High frequency) 4000 Hz:/8000 Hz:
Select the frequency (4 kHz/8 kHz) at which the high range
will be adjusted.
HIGH GAIN -1 5-+ 1 5 dB
Specify the high frequency gain (amount of boost or cut).
Positive(+) settings will emphasize (boost) the high range.
P 1 FREQ (Peaking 1 frequency)
200/250/315/400/500/630/800/1000/1250/1600/2000/2500/3150/
4000/5000/6300/8000 (200-8000 Hz)
Specify the center frequency of the region in which the boost
or cut will take place.
P 1 Q (Peaking 1
Q)
0.5/ 1.0/2.0/ 4.0/8.0
Specify the width of the region centered on the Pl FREQ
setting.
Higher settings will cause the region affected by Pl GAIN to
be narrower.
P 1 GAIN (Peaking 1 gain) -15-+ 15 dB
Specify the gain (amount of boost or cut) that will take place
in the region specified by Pl FREQ and Pl Q.
Positive ( +) settings will emphasize (boost) the region
specified by Pl FREQ and PlQ.
P2 FREQ (Peaking 2 frequency)
200/250/315/400/500/630/800/1000/1250/1600/2000/2500/3150/
4000/5000/6300/8000 (200-8000 Hz)
Specify the center frequency of the region in which the boost
or cut will take place.
P2
Q
(Peaking 2
Q)
0.5/1.0/2.0/ 4.0/8.0
Specify the width of the region centered on the P2 FREQ
setting.
Higher settings will cause the region affected by P2 GATN to
be narrower.
Chapter 6 Using the Built-in Effects
I
P2 GAIN (Peaking 2 gain) -15-+ 15 dB
Specify the gain (amount of boost or cut) that will take place
in the region specified by P2 FREQ and P2 Q.
Positive ( +) settings will emphasize (boost) the region
specified by P2 FREQ and P2Q.
LEVEL (Output level) 0-127 #
Specify the output volume.
2: OVERDRIVE
Overdrive produces a natural-sounding distortion similar to
that produced by a vacuum tube amplifier.
Lin
Amp
2-Band
Simulator
EO
Rin
DRIVE 0-127
#
Specify the depth of distortion. The volume will change
together with the depth of distortion.
PAN (Output pan) L64-0-R63
Specify the stereo location of the output sound.
A setting of L64 is far left, 0 is center, and R63 is far right.
AMP TYPE (Amp simulator type)
Small/Built-ln/2-Stack/3-Stack
Select the type of guitar amp.
Small:
Small amp
Built-In:
Built-in type amp
2-Stack:
Large two-level stack
3-Stack:
Large three-level stack
LOW GAIN -15-+15 dB
Adjust the low frequency gain (amount of boost or cut).
Positive(+) settings will emphasize (boost) the low
frequency range.
HIGH GAIN -15-+ 15 dB
Adjust the high frequency gain (amount of boost or cut).
Positive(+) settings will emphasize (boost) the high
frequency range.
LEVEL (Output level) 0-127
Specify the output volume.
You can use the Output Level setting to even out the volume
difference between the sound with and without Overdrive.
55
I
Advertisement
Table of Contents
