Resolving Problems - Honda Miimo HRM310 Owner's Manual

Resolving problems

Resolving problems
Unless having the power on is necessary to check something, turn off the power when checking the condition
of the lawn mower or the blade.
Problem
The lawn mower cannot be
charged.
The lawn mower will not enter an
area, or the blades and movement
have stopped.
The lawn mower stops frequently.
The lawn mower leaves the preset area
or behaves differently from the settings.
The boundary wire has slackened
and come out of the ground or a
peg has come out of the ground.
A strange noise is heard from the
lawn mower or the lawn mower
vibrates.
Lawn mower does not leave the
docking station. No error message
is displayed.
Poor mowing results.
Lawn mower does not work inside
the boundary wire.
The lawn mower goes out of the
boundary wire.
The lawn mower does not dock
into the docking station.
Noticeable wheel tracks.
The lawn mower does not enter
narrow corridors.
62
Check the connections, and charge the lawn mower again.
If the lawn mower cannot be charged, contact your dealer.
The lawn mower will try to evade an area with a slope of more than 24°. In the
case of a 25 - 35 degree slope (depending on unevenness of the ground)
- The lawn mower will try to escape from the slope
In the case of a slope more than 35 degree slope
- The lawn mower will stop due to "Excessive tilt"
Operation of this product with other wireless devices, remote controls, or
electric fences is not guaranteed. Contact your dealer.
See the error message on the screen and follow the instructions before contacting your
dealer. If you cannot solve the issue, contact your dealer with the error messages ready.
Stop the lawn mower because it may cut the wire.
Be careful not to trip on the boundary wire or peg. Contact your dealer.
Check the blades if they are broken or not. Broken blades can create an
unbalanced blade disc. It can create noise.
Try to use "Quiet timer".
Contact your dealer if it cannot be solved.
- Timers were not set up correctly. Check the timer settings. See "4 MENU
25
SETTINGS" (M page ).
- The Date and Time are incorrect. Check the clock (M page 50).
- The manual STOP button was pressed, but the H button was not pressed
before closing the control panel cover.
- The lawn mower is in inactive mode.
Another cause could be that the machine is in "Home" mode.
- The lawn mower in the Auto mode will always charge the battery up to 100%. If
you want to make the lawn mower to start mowing sooner, change the operating
mode to the Manual mode.
- The cutting height is incorrect or the grass is too high. Adjust the cutting height
or cut with a standard lawn mower fi rst if the grass is too high.
- Check the condition of the blades (M page 68).
- If there are electromagnetic and electric fi elds near the boundary wire such
as power line, factory, electric noise might affect the movement of your lawn
mower. Contact your dealer.
- A power failure occurred. The lawn mower behaves as follows:
In case that the power supply is cut off for more than 30 minutes, the lawn mower will
shut off automatically to prevent the battery from becoming empty.
In case that the power supply comes back within 30 minutes, the lawn mower
will start mowing automatically. *
* The lawn mower will return to the docking station if the battery residual capacity is low.
Record where the lawn mower goes out of wire.
Check the ground condition, weather condition and tire condition when the lawn mower
goes out of the boundary wire. Clean up the tire if it has any mud, leaves, or grass. Try
to continue. If the issue occurs frequently, contact your dealer.
Check station condition if it deformed or not. Check boundary wire underneath the
station (M page 12). Clean up the charging terminal of both the lawn mower and station.
Try to reduce the work timer.
You can reduce the work timer automatically by using "Seasonal timer". Try to
increase "passage width".
Check the "passage width" setting. If necessary, you can use the "Narrow
passage" function (M page 37).
Solution