Danfoss VLT HVAC Drive FC 102 Design Manual page 212

General Specifications and ...
Line Power Supply 525–690 V AC
Normal overload 110% for 1 Minute
Typical Shaft Output [HP]
at 525–550 V
Typical Shaft Output [kW] at 690
Typical Shaft Output [HP] at 575
IP 21/ NEMA 1 at 525 V
IP 21/ NEMA 1 at 575 V
IP 21/ NEMA 1 at 690 V
Output Current
Continuous (6 x 525–550 V) [A]
Intermittent (6 x 550 V)
Continuous (6 x 551–690 V) [A]
Intermittent (6 x 551–690 V) [A]
Continuous KVA (550 V) [KVA]
Continuous KVA (575 V) [KVA]
Continuous KVA (690 V) [KVA]
8 8
Max Input Current
Continuous (6 x 550 V) [A]
Continuous (6 x 575 V) [A]
Continuous (6 x 690 V) [A]
Max. external electrical fuses
Max Cable Size:
Motor (mm 2 /AWG
Line power (mm
Regeneration terminals (mm
Brake (mm 2 /AWG
Estimated Power loss at 690 V AC at
rated max. load (W)
Estimated Power loss at 575 V AC at
rated max. load (W)
Weight Enclosure IP21 kg (lbs)
Weight enclosure IP 54 kg (lbs)
4)
Efficiency
Output Frequency
Heatsink overtemp trip
Power card ambient trip
Table 8.8 Line Power Supply 525–690 V AC
1) For type of fuse, consult the Instruction Manual
2) American Wire Gauge
3) The typical power loss is at normal conditions and expected to be within ± 15% (tolerance relates to variety in voltage and cable conditions.)
These values are based on a typical motor efficiency (eff2/eff3 border line). Lower efficiency motors add to the power loss in the adjustable
frequency drive and the opposite is also true. If the switching frequency is raised from nominal, the power losses rise significantly. LCP and typical
control card power consumptions are included. Further options and customer load can add up to 30 W to the losses (though typically only 4 W
extra for a fully loaded control card or options for slot A or slot B, each)
4) Measured using 16.5 ft [5 m] shielded motor cables at rated load and rated frequency.
210
Design Guide
P450
NO
355
450
450
470
515
450
495
448
448
538
453
434
434
1)
630
2) )
2 2)
/AWG )
2 2)
/AWG )
2) )
4974
3)
5128
3)
440/656 (880/1443)
Danfoss A/S © Rev. 2014-01-13 All rights reserved.
P500 P560 P630 P710
NO NO NO NO
400 450 500 560
500 560 630 710
500 600 650 750
F8/F9
F8/F9
F8/F9
523 596 630 763
575 656 693 839
500 570 630 730
550 627 693 803
498 568 600 727
498 568 627 727
598 681 753 872
504 574 607 743
482 549 607 711
482 549 607 711
630 630 630 900
8 x 300 MCM (8 x 150)
8 x 500 MCM (8 x 250)
4 x 250 MCM (4 x 120)
4 x 350 MCM (4 x 185)
5623 7018 7793 8933
5794 7221 8017 9212
880/1096 (1936/2471)
110°C 95°C
P800 P900 P1M0
NO NO NO
670 750 850
800 900 1000
950 1050 1150
F10/F11
F10/F11
F10/F11
889 988 1108
978 1087 1219
850 945 1060
935 1040 1166
847 941 1056
847 941 1056
1016 1129 1267
866 962 1079
828 920 1032
828 920 1032
900 900 1600
12 x 300 MCM (12 x 150)
10310 11692 12909
10659 12080 13305
1022/1238 (2248/2724)
0.98
0–525 Hz
105°C 95°C 95°C
85°C
P1M2 P1M4
NO NO
1000 1100
1200 1400
1350 1550
F12/F13
F12/F13
F12/F13
1317 1479
1449 1627
1260 1415
1386 1557
1255 1409
1255 1409
1506 1691
1282 1440
1227 1378
1227 1378
2000 2500
15358 17602
15865 18173
105°C 95°C
MG16C122