Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Planmeca SingLED
Summary of Contents for Planmeca SingLED
- Page 1 user's manual...
-
Page 3: Table Of Contents
Attaching USB device to operating light ................. 7 CLEANING .......................8 Light assembly ....................... 8 Arm ..........................9 INDICATION OF ERRONEOUS OPERATION ..........10 DISPOSAL OF OPERATING LIGHT .............11 TECHNICAL SPECIFICATIONS ..............12 MAINTENANCE PARTS ................21 Planmeca SingLED operating light i User’s manual... - Page 4 IEC 60364 - equipment is used according to the operating instructions. Planmeca pursues a policy of continual product development. Although every effort is made to produce up-to-date product documentation this publication should not be regarded as an infallible guide to current specifications.
-
Page 5: Introduction
The operating light reaches all the areas of the oral cavity and the long operating light arm ensures that the entire mandibular area is illuminated. The device system including the Planmeca SingLED operating light must fulfil the medical device EMC requirements of the Standard IEC 60601-1-2. -
Page 6: Warnings And Cautions
CAUTION Do not allow the patient to grab the operating light handles or arm when getting seated or getting up from the patient chair. CAUTION The light source of the SingLED operating light may cause retinal injury if viewed upon directly. Protect the patient’s and dental treatment staff’s... -
Page 7: Using Operating Light
USING OPERATING LIGHT USING OPERATING LIGHT NOTE If the Planmeca SingLED operating light is attached to a Planmeca dental unit, the light’s operation is described in the dental unit’s user’s manual. NOTE The light must be moved from the handles only. Do NOT move the light from the arm or from the light body. -
Page 8: Adjusting Brightness Of Operating Light
Planmeca Compact or a Planmeca Sovereign dental unit. NOTE If the operating light is installed to the Planmeca Compact i dental unit you can change the operation mode of the light by pressing the on/off switch for longer than 15 seconds (you will hear two signal tones;... -
Page 9: Adjusting Handle Positions
Remove the handle by pulling it carefully outwards (1). Rotate the handle to desired angle (2) and push it back to its position (3). Rotate the plastic sleeve so that it fits the handle. Plastic sleeve Handle User’s Manual Planmeca SingLED operating light 5... -
Page 10: Adjusting Patient Mirror Position
USING OPERATING LIGHT Replace the handles when needed, e.g. when they come off too easily. Use only handles supplied by Planmeca (see picture below). Adjusting patient mirror position When you want to turn the mirror away from the patient, turn the mirror upward as shown below. Do not turn the mirror to the sides. -
Page 11: Attaching Usb Device To Operating Light
USING OPERATING LIGHT Attaching USB device to operating light The operating light has a USB port to which you can attach a USB device. User’s Manual Planmeca SingLED operating light 7... -
Page 12: Cleaning
Light assembly The Planmeca SingLED operating light is dustproof and impervious to spray vapour. All exposed surfaces should be periodically wiped clean with a non-abrasive cleaning agent designed for cleaning dental units. -
Page 13: Arm
The arm should be periodically wiped clean with a non- abrasive cleaning agent designed to be used with dental units. Stronger agents can be used for disinfecting. We recommend Dürr System Hygiene FD 333 or a similar disinfecting solution. User’s Manual Planmeca SingLED operating light 9... -
Page 14: Indication Of Erroneous Operation
INDICATION OF ERRONEOUS OPERATION INDICATION OF ERRONEOUS OPERATION If the Planmeca SingLED operating light detects a malfunction in the normal operation, the sensor indicator Sensor light starts to flash. indicator light The reason for an erroneous operation may be one of the following: •... -
Page 15: Disposal Of Operating Light
The risks involved and the necessary precautions must be taken into account when handling waste products. Disposal of Planmeca SingLED operating light X = action, (X) = action in cases where processing is available Hazardous... -
Page 16: Technical Specifications
Supply frequency 50 / 60 Hz Power output 24V/1.33A max NOTE: When the Planmeca SingLED operating light is connected to other equipment, the current must be limited to max. 2 A with e.g. a fuse. Environmental requirements Operating conditions: Temperatures: +15°C to +35°C (+59°F to +95°F) - Page 17 5.2.7 Shadow: the hard shadow is too large in vertical and horizontal direction. 5.2.8 Colour rendering index: Ra is too low for diagnostic purposes. 5.2.9 UV irradiance: not measured 180nm to 200nm, because limition of measuring device. User’s Manual Planmeca SingLED operating light 13...
- Page 18 TECHNICAL SPECIFICATIONS Dimensions Planmeca SingLED operating light User’s Manual...
- Page 19 TECHNICAL SPECIFICATIONS User’s Manual Planmeca SingLED operating light 15...
- Page 20 TECHNICAL SPECIFICATIONS Ceiling installation Side vie Maximum room height 3000 mm Top view Maximum reach of outermost point of operating light Second joint rotation angle with rotation limit Planmeca SingLED operating light User’s Manual...
- Page 21 TECHNICAL SPECIFICATIONS Wall installation Side view Recommended max. height from floor 1670 mm Top view Maximum reach of outermost point of operating light Second joint rotation angle with rotation limit User’s Manual Planmeca SingLED operating light 17...
- Page 22 TECHNICAL SPECIFICATIONS Dental unit installation Side view Top view Maximum reach of outermost point of operating light Second joint rotation angle with rotation limit Planmeca SingLED operating light User’s Manual...
- Page 23 TECHNICAL SPECIFICATIONS Dimensions of the wall plate (in mm) User’s Manual Planmeca SingLED operating light 19...
- Page 24 TECHNICAL SPECIFICATIONS Dimensions of the ceiling adapter (in mm) Dimensions of ceiling adapter cover (in mm) Planmeca SingLED operating light User’s Manual...
-
Page 25: Maintenance Parts
MAINTENANCE PARTS MAINTENANCE PARTS Part Part number Power supply MENB1030A2402F01 24V DC, (100-240VAC) 10017273 Handle 10020763 User’s Manual Planmeca SingLED operating light 21... - Page 28 Planmeca Oy | Asentajankatu 6 | 00880 Helsinki | Finland tel. +358 20 7795 500 | fax +358 20 7795 555 | sales@planmeca.com | www.planmeca.com...