Setting Items - Oce CS6407 Quick Reference Manual

Setting items

INK MENU
Menu
XXX INK LEVELZZZ%
DATE:YY/MM/DD
MEDIA MENU
Menu
ROLL(XXXXXX)
YYYmm
SHEET(XXXXXX)
YYYYmm
FACE(XXXXXX)
YYYYmm
BACK(XXXXXX)
YYYYmm
NEST(XXXXXX)
YYYmm
MEDIA REG MENU
Menu
#SELECT MEDIA
>XX:YYYYYY
#RENAME MEDIA
>XX:YYYYYY
#MEDIA ADV VALUE
>XX:YYY.YY%
#USE EDGE GUARD
>XX:YES
#MEDIA ADV MODE
>XX:FWD ONLY
#MEDIA BACK MODE
>XX:BACK & FWD
#SUCTION FAN LEVEL
>XX:HIGH
#AFTERHEATER T
>XX:30°C
#PRINTHEATER T
>XX:40ºC
#PREHEATER T
>XX:40°C
#COLOR STRIPE
>XX:ON
#PH HEIGHT VAL
>XX:+0.0
#IMAGE IMPROVE.
>XX:ON
#PH CLEANING
>XX:START & END
#BACK ADJUST VAL
>XX:+0000PULSE
#PH REST PERIOD
>XX:0000CYCLES
#PH REST TIME
>XX:10sec
#BIDIR ADJ2 L CCC
>XX:+00
#BIDIR ADJ3 L CCC
>XX:+00
#BIDIR ADJ4 L XXX
>XX:+00
INK LEVEL shows remaining ink. DATE shows the manufactured date of ink cartridge.
XXXXXX: Media name
YYYY: Media width
XXXXXX: Media name
YYYY: Media width
XXXXXX: Media name
YYYY: Media width
XXXXXX: Media name
YYYY: Media width
XXXXXX: Media name
YYYY: Media width
Select the media number of media to be registered or parameter-corrected.
Name (register) the media number selected in [SELECT MEDIA]. Six (6) digits of character (or code) can
be entered for the media name. For character string of 6 digits, codes, alphanumerics and katakana
characters can be used.
Set MEDIA ADVANCE VALUE. Set the advance value so that the banding (horizontal stripes of path
splicing) is not visible.
Select whether to use the media edge guard or not. With this setting, the right and left margins of
media vary.
Select a media advance mode.
Select a media advance mode.
Select the force (air volume of fan) to suck the media to the platen.
Set the afterheater temperature. However, when "**" is set, the postheater does not work.
Set the printheater temperature. However, when "**" is set, the print heater does not work.
Set the preheater temperature. However, when "**" is set, the preheater does not work.
Select whether to print color stripes or not.
Adjust the print head height.
Select whether to automatically correct the print quality or not.
To keep the print head condition, select a cleaning mode which is automatically performed by the
printer.
Set the back adjust value of media. This value is used to correct the splice of two images divided by the
auto-cleaning (PH CLEANING [MODE2] performed during printing.
Scanning of the print head rests at every certain print length during printing. Set this time period to
prevent nozzle-out of the print head. Normally, set it to [0000CYCLES].
Corresponding to [ PH REST PERIOD], set the scan rest time. When [0] is set for [PH REST PERIOD], this
parameter is ignored. Set this rest time to prevent nozzleout of the print head. Set it to [10 sec] as a rule
of thumb.
The reciprocating correction adjusts the shift between two ways of bidirectional print. With this menu,
correction values for print modes (NORMAL1, NORMAL2, QUALITY and DENSITY2) are set.
The reciprocating correction adjusts the shift between two ways of bidirectional print. With this menu,
correction values for print modes (DRAFT1) are set.
The reciprocating correction adjusts the shift between two ways of bidirectional print. With this menu,
correction values for print mode (FINE DRAFT1) are set.
Outline of functions
Outline of functions
Outline of functions
29