ACME CHEETAH LED-GF50 User Manual page 5

display will blink. Use the DOWN and UP button to calibrate the dimmer for a maximum
output from (limited to 50% of the really max. output) to
is not limited). Once the mode has been selected, press the ENTER button to setup. To go
back to the functions without any change press the MENU button again. Hold and press the
MENU button about 2 seconds or wait for 60 seconds to exit the menu mode.
Sound Mode
Press the MENU button to show
display will blink. Use the DOWN and UP button to select the
(sound off) mode. Once the mode has been selected, press the ENTER button to setup. To
go back to the functions without any change press the MENU button again. Hold and press
the MENU button about 2 seconds or wait for 60 seconds to exit the menu mode.
Blackout Mode
Press the MENU button to show
display will blink. Use the DOWN and UP button to select the
(no blackout) mode. Once the mode has been selected, press the ENTER button to
setup. To go back to the functions without any change press the MENU button again. Hold
and press the MENU button about 2 seconds or wait for 60 seconds to exit the menu mode.
Led Display
Press the MENU button to show
display will blink. Use the DOWN and UP button to select the
(Led off) mode. Once the mode has been selected, press the ENTER button to setup. To
go back to the functions without any change press the MENU button again. Hold and
press the MENU button about 2 seconds or wait for 60 seconds to exit the menu mode.
Display Inversion
It is good for you to install the unit on the floor or under ceiling. Press the MENU button to
show on the display. Press the ENTER button to change to the mode
(display normal), It will automatically store after 8 seconds. Or press the ENTER button
again return to the mode (display inversion). To go back to the functions without
any change press the MENU button again. Hold and press the MENU button about 2
seconds or wait for 60 seconds to exit the menu mode.
(maximum output
on the display. Press the ENTER button and the
(sound on) or
on the display. Press the ENTER button and the
(yes blackout) or
on the display. Press the ENTER button and the
(Led on) or
8-
Display normal mode for the fixture putting on the floor.
Display inversion mode for the fixture fixing under ceiling.
Self-Test
Press the MENU button to show
unit will run self-test by built-in program. To go back to the functions without any change
press the MENU button again. Hold and press the MENU button about 2 seconds or wait for
60 seconds to exit the menu mode.
Temperature Test
Press the MENU button to show
display will show the temperature of the unit. To go back to the functions without any
change press the MENU button again. Hold and press the MENU button about 2 seconds
or wait for 60 seconds to exit the menu mode.
Fixture Hours
Press the MENU button to show
display will show the number of working hours of the unit. To go back to the functions
without any change press the MENU button again. Hold and press the MENU button about
2 seconds or wait for 60 seconds to exit the menu mode.
Software version
Press the MENU button to show
display will show the version of software of the unit. To go back to the functions without
any change press the MENU button again. Hold and press the MENU button about 2
seconds or wait for 60 seconds to exit the menu mode.
PRO Defaults
Press the MENU button to show
display will blink. Use the DOWN and UP button to select the
to set the fixture to PRO Defaults settings) or
To go back to the functions without any change press the MENU button again. Hold and
press the MENU button about 2 seconds or wait for 60 seconds to exit the menu mode.
Reset
on the display. Press the ENTER button and the
on the display. Press the ENTER button and the
on the display. Press the ENTER button and the
on the display. Press the ENTER button and the
on the display. Press the ENTER button and the
(run built-in program
. Press the ENTER button to setup.
9-