Led Display Inversion; Energy Saving Mode; Operating Modes - ADJ Mega QPlus GO User Instructions

Mega QPlus GO
System Menu: The display will lock after 30 seconds, press
the MODE button for 3 seconds to unlock.
LED Display On/Off:
To set the LED display to turn off after 10 seconds, press the MODE
button until "don" is displayed, press the UP button to display "doff".
Now the display will disappear after 10s. Press any button to turn
the display on again. Be advised though that the display will turn off
automatically after 10 seconds.
To set the display press the MODE button until "dXX" is displayed.
Use the UP or DOWN buttons to select either:
"don" = LED display on at all times.
"doFF" = LED display shuts off after 10 seconds.

LED Display Inversion:

Follow these instructions to flip the display 180° so that the display
can be read upside down.
1. Plug the fixture in and press the MODE button until "dXX" is dis-
played. "XX" represents either "on" or "oFF".
2. Press the SET UP button until "Stnd" is displayed.
3. Press the UP or DOWN buttons to reverse the display 180°.

Energy Saving Mode:

1. Plug the fixture in and press the MODE button until "bXXX" is dis-
played. "XX" represents the current battery life.
2. Press the SET UP button so that "bSXX" is displayed.
3. Press the UP or DOWN buttons to turn eneryg saving mode either
"On" or "Off".

Operating Modes:

The Mega QPlus GO has five operating modes:
• RGB+UV Dimmer Mode - Choose one of the four colors to remain
static or adjust the intensity of each color to make your desired
color.
• Sound-Active mode - The unit will react to sound, chasing through
the built in programs. There are 16 sound active modes.
• Auto Run Mode - In Auto Run mode, you can choose 1 of 16
color change modes, 1 of 16 color fade modes, or a combo color
ADJ Products, LLC - www.adj.com - Mega QPlus GO User Manual Page 10
Operating Instructions Mega QPlus GO
change & fade mode.
• Static Color Mode - There are 64 colors to choose from.
• DMX control mode - This function will allow you to control each
individual fixtures traits with a standard DMX 512 controller.
DMX Mode:
Operating through a DMX controller gives the user the freedom to
create their own programs tailored to their own individual needs. This
function also allows you to use your fixtures as spot lights. The Mega
QPlus GO has 8 DMX modes: 1 channel mode, 2 channel mode, 3
channel mode, 4 channel mode, 5 channel mode, 6 channel mode,
7 channel mode, and 8 channel mode. See page's 20-27 for each
mode's DMX traits.
1. This function will allow you to control each individual fixture's
traits with a standard DMX 512 controller.
2. To run your fixture in DMX mode press the MODE button until
"d.XXX" is displayed. "XXX" represents the current displayed DMX
address. Use the UP or DOWN buttons to select your desired
DMX address, then press the SETUP button to select your DMX
Channel mode.
3. Use the UP or DOWN buttons to scroll through the DMX Channel
modes. The Channel modes are listed below:
• To run the 1 Channel Mode, press the MODE button until "Ch01"
is displayed. This is the 1 Channel DMX Mode.
• To run the 2 Channel Mode, press the MODE button until "Ch02"
is displayed. This is the 2 Channel DMX Mode.
• To run the 3 Channel Mode, press the MODE button until "Ch03"
is displayed. This is the 3 Channel DMX Mode.
• To run the 4 Channel Mode, press the MODE button until "Ch04"
is displayed. This is the 4 Channel DMX Mode.
• To run the 5 Channel Mode, press the MODE button until "Ch05"
is displayed. This is the 5 Channel DMX Mode.
• To run the 6 Channel Mode, press the MODE button until "Ch06"
is displayed. This is the 6 Channel DMX Mode.
• To run the 7 Channel Mode, press the MODE button until "Ch07"
is displayed. This is the 7 Channel DMX Mode.
• To run the 8 Channel Mode, press the MODE button until "Ch08"
is displayed. This is the 8 Channel DMX Mode.
ADJ Products, LLC - www.adj.com - Mega QPlus GO User Manual Page 11
Operating Instructions