ADJ Mega QPlus GO User Instructions page 7

Mega QPlus GO
4. Please see pages 20-27 for DMX values and traits.
5. After you have chosen your desired DMX Channel mode plug in
the fixture via the XLR connections to any standard DMX control-
ler.
RGB+UV Dimmer Mode:
1. Plug the fixture in and press the MODE button until:
2. When "r.XXX" is displayed you are in Red dimming mode. Press
the UP and DOWN buttons to adjust intensity.
3. When "G.XXX" is displayed you are in Green dimming mode.
Press the UP and DOWN buttons to adjust intensity.
4. When "b.XXX" is displayed you are in Blue dimming mode. Press
the UP and DOWN buttons to adjust intensity.
5. When "u.XXX" is displayed you are in UV dimming mode. Press
the UP and DOWN buttons to adjust intensity.
6. After you have adjusted the RGB & UV colors to make your
desired color you can then activate strobing by pressing the SET
UP button to enter the Flash (strobe) mode.
7. "FS.XX" will be displayed, this is Flash mode. The Flash can be
adjusted between "FS.00" (flash off) to "FS.15" (fastest flash).
Sound Active Mode:
1. Plug the fixture in and press the MODE button until "SoXX" is dis-
played. "XX" represents the current sound active mode (1-16).
2. Use the UP or DOWN buttons to find your desired sound active
mode.
3. Press the SET UP button to enter sound sensitivity adjustment.
"SJ-X" will be displayed. Use the UP or DOWN buttons to adjust
the sensitivity. "SJ-1" is the lowest sensitivity, "SJ-8" is the high-
est.
Auto Run Mode:
There are 3 types of Auto Run Modes to choose from; Color Fade,
Color Change, and both modes running together. The running speed
is adjustable in all 3 modes.
1. Plug the fixture in and press the MODE button until either "AFXX",
"AJXX", or "A-JF" is displayed.
• AFXX = Color Fade mode, there are 16 Color Fade modes to
choose from. Use the UP or DOWN buttons to scroll through the
ADJ Products, LLC - www.adj.com - Mega QPlus GO User Manual Page 12
Operating Instructions Mega QPlus GO
different Auto Fade modes.
• AJXX = Color Change mode, there are 16 Color Change modes to
choose from. Use the UP or DOWN buttons to scroll through the
different Auto Change modes.
• A-JF = Both Color Fade and Color Change modes running.
2. After you have chosen your desired running mode press the SET
UP button until "SP.XX" is displayed. When this is displayed you
can adjust the running speed of your desired program. Use the
UP or DOWN button to adjust the speed between "SP.01" (slow-
est) and "SP.16" (fastest). Once you have set your desired running
speed, press the SET UP button to return to your desired Auto
Run Mode.
Static Color Mode:
1. Plug the fixture in and press the MODE button until "CLXX" is dis-
played.
2. There are 64 colors to choose from. Select your desired color by
pressing the UP and DOWN buttons. After you have selected your
desired color you can activate strobing by pressing the SET UP
button to enter the Flash (strobe) mode.
3. "FS.XX" will be displayed, this is Flash mode. The Flash can be
adjusted between "FS.00" (flash off) to "FS.15" (fastest flash).
DMX State:
This mode can be used as a precaution mode, that in case the DMX
signal is lost, the operating mode chosen in the setup is the running
mode the fixture will go into when the DMX signal is lost. You can also
set this as the operating mode you would like the unit to return to when
power is applied.
1. Plug the fixture in and press the MODE button until "d.XXX" is dis-
played. "XXX" represents the current displayed DMX address.
2. Press the SET UP button so that "nodn" is displayed. Use the UP
and DOWN buttons to scroll through the DMX states.
• "bLAC" (Blackout) - If the DMX signal is lost or interrupted,
the unit will automatically go into stand by mode.
• "LASt" (Last State) - If the DMX signal is lost or interrupted,
the fixture will stay in the last DMX set up. If power is applied and
this mode is set, the unit will automatically go into the last DMX set
up.
ADJ Products, LLC - www.adj.com - Mega QPlus GO User Manual Page 13
Operating Instructions