Led Display On/Off; Led Display Inversion; Operating Modes; Static Color Mode - ADJ UB 12H User Instructions

UB 12H

LED Display On/Off:

To set the LED display to turn off after 10 seconds, press the MODE but-
ton until "don" is displayed, press the UP button to display "doff". Now
the display will disappear after 10s. Press any button to turn the display
on again. Be advised though that the display will turn off automatically
after 10 seconds.

LED Display Inversion:

Follow these instructions to flip the display 180° so that the display can
be read upside down.
1. Plug the fixture in and press the MODE button until "dXX" is dis-
played. "XX" represents either "on" or "oFF".
2. Press the SET UP button until "Stnd" is displayed.
3. Press the UP or DOWN buttons to "flip" the display 180°.

Operating Modes:

The UB 12H has six operating modes:
• Static Color Mode - There are 63 colors to choose from.
• RGBWA+UV Dimmer Mode - Choose one of the 6 colors to remain
static or adjust the intensity of each color to make your desired
color.
• Built-In Program - There are 22 built-in programs to choose from
with multiple adjustments.
• Auto Run - A auto program will run with adjustable fade speed
and strobe.
• Sound-Active mode - The unit will react to sound, chasing through
the built in programs.
• DMX control mode - This function will allow you to control each
individual fixtures traits with a standard DMX 512 controller.

Static Color Mode:

1. Plug the fixture in and press the MODE button until "CLXX" is
displayed.
2. There are 63 colors to choose from. Select your desired color by
pressing the UP and DOWN buttons. After you have selected
your desired color you can activate strobing by pressing the SET
UP button to enter the Flash (strobe) mode.
3. "FS.XX" will now be displayed, this is Flash mode. The Flash can
be adjusted between "FS.00" (flash off) to "FS.15" (fastest flash).
ADJ Products, LLC - www.adj.com - UB 12H User Manual Page 8
Operating Instructions
UB 12H
RGBWA & UV Dimmer Mode:
1. Plug the fixture in and press the MODE button until "r.XXX"
is displayed. You are in Red dimming mode.
2. Press the UP and DOWN buttons to adjust intensity. After you
have finished adjusting the intensity, or if you would like to skip to
the next color, press the SET UP button.
3. When "G.XXX" is displayed you are in Green dimming mode.
Press the UP and DOWN buttons to adjust intensity.
4. When "b.XXX" is displayed you are in Blue dimming mode.
Press the UP and DOWN buttons to adjust intensity.
5. When "U.XXX" is displayed you are in White dimming mode.
Press the UP and DOWN buttons to adjust intensity.
6. When "A.XXX" is displayed you are in Amber dimming mode.
Press the UP and DOWN buttons to adjust intensity.
7. When "u.XXX" is displayed you are in UV dimming mode. Press
the UP and DOWN buttons to adjust intensity.
8. After you have adjusted the colors to make your desired color
you can then activate strobing by pressing the SET UP button to
enter the strobe mode.
9. "FSXX" will be displayed, this is strobe mode. The strobe can be
adjusted between "00" (flash off) to "15" (fastest flash).

Auto Run Mode:

In this mode the UB 12H will run a auto program.
1. Plug the fixture in and press the MODE button until "AUTO" is dis-
played.
2. After you have activated Auto Run mode, press the SET UP but-
ton to adjust the fade time.
3. Once you press SET UP "Fd.XX" should be displayed. Use the UP
or DOWN buttons to set the fade speed to either "Fd.00" (fade
off) or between "Fd.01" (fastest speed) and "Fd.99" (slowest
speed). After adjusting the fade speed, press SET UP if you
wish to activate the Flash mode.
4. "FS.XX" will now be displayed, this is Flash mode. The Flash can
be adjusted between "FS.00" (flash off) to "FS.15" (fastest flash).
ADJ Products, LLC - www.adj.com - UB 12H User Manual Page 9
Operating Instructions