Table of Contents
Advertisement
90
HorneLink®
Remote control units for garage door openers
in Canada are set ta stop transmitting radio
frequency signals after two seconds. This time
~
Ifthe 5 minute time limit is exceeded, the
emergency flashers will flash one time to in-
dicate that the process has been terminated.
In this case, repeat steps 4 through 9.
If the emergency flashers do not flash
three
times (after about 15-60 seconds), program-
ming was not successful. In this case, repeat
steps 4 through 9.
Phase 3: roUing code programming
~
A second persan on a ladder who can safely
reach the garage door opener motor is rec-
ommended.
Il. Locate the "learn" button on the garage
. door opener motor (refer to the operating
instructions for the opener, as the loca-
tion of this button may vary by manufac-
turer).
12. Press and release the learn button on the
garage door opener motor.
~
Note: once the button is pressed, there are
30 seconds in which to initiate the next
step.
13.
On the HomeLink'" keypad inside the vehi-
cle, firmly press and hold the HomeLink'"
button previously programmed in phases
1 and 2 for two seconds and release. Re-
peat this sequence twice.
~
50me vehicles may require the press/hold/
release sequence up to three times to com-
plete the training process.
~
HomeLink'" should now activa
te
your rolling
code equipped de vice.
10. Press and hold the trained HomeLink'"
button and observe the indicator light
®
~fig.
95.
~
Ifthe indicator light is solid/continuous,
programming is complete and your device
should activate when you press and release
the trained HomeLink'" button.
~
If the indicator light blinks rapidly for 2 sec-
onds and is then a solid!continuous light,
proceed with phase 3 ta program a rolling
code device.
6. Hold the
original remote control
at a dis-
tance between 0-6 in. (0-15 cm) from the
bumper below the appropriate headlight
for your
vehicle~
fig. 96
(use the shortest
distance possible).
7. Aim the remote controljust below the
driver side headlight.
8. Press and hold the activation button on
the remote control.
~
May be different in Canada. If sa, press and
re-press (cycle) the activation button on your
remote control every two seconds.
9. The emergency flashers will flash three
times (after about 15-60 seconds) when
the programming is successful. Release
the button on the remote control.
~
Ta progrom more devices, repeat steps 4 ta
9.
Phase 2:
programming the bumper mounted trans
mitter
_ _
---------------------------~H~o~rn~e~L~i~n~k~®
---
phase 1:
programming the overhead keypad
1. Make sure your vehicle is within operating
range of the remote controlled garage
door opener.
2. Set the parking brake ~
8.
in General in-
formation on page 90.
3. Turn the ignition on. Do not start the en-
gine!
4.
Press and hold the two outside Home-
Link'" buttons
CD
and @for approxi-
mately 20 seconds until indicator light
®
~fig.
95 begins to flash. Then release
both buttons. Do not hold the buttons for
longer than 30 seconds.
~
This procedure only needs ta be performed
once. It erases the factory-set default codes
and does not have ta be repeated ta pro-
gram additional remote controls.
5. Press and hold the HomeLink'" button
CD,
@)or @until the indicator light
®
starts flashing
slow/y.
Release the button.
~
The system will remain in programming
mode for 5 minutes. Go ta the front of the
vehicle and proceed with phase 2.
tivated, this can overstrain motor and
damage its electrical components - an
overheated motor is a fire hazard!
- To avoid possible injuries or property
damage, please always make absolutely
certain that no persons or abjects are lo-
cated in the range of motion of any
equipment being operated.
---
@
Tips
- Ifyou would like more information on
HomeLink®, where ta purchase the
HomeLink® compatible products, or
would like ta purchase the HomeLink®
Home Lighting Package, please call toll-
free: 1-800-355-3515.
- For Declaration of Compliance to United
5tates FCC and Industry Canada regula-
tions
~
page 248.
Programming the HomeLink®
.1
transmitter
. .
Fig. 96 Front bumper, driver side: location of transmit-
ter
unit
The transmitter is programmed in two phas-
es.
For rolling code tronsmitters, a third
phase is also necessary.
-
- Never IJse the HomeLink® transmitter
with any garage door opener that does
have not the safety stop and reverse fea-
ture as required by federalsafety stand-
ards. This includes any garage door open-
er model manufactured before April l,
1982.
- A garage door opener which cannot de-
tect an object, signaling the door to stop
and reverse does not meet current feder-
alsafety standards. Using a garage door
opener without these features increases
risk of serious injury or death.
- For safety reasons never release the
parking brake or start the engine while
anyone is standing in front of the vehicle.
- A garage door or an estate gate may
sometimes be set in motion when the
HomeLink® remote control is being pro-
grammed. If the device is repeatedly ac-
&
WARNING
The HomeLink universol remote control con
be progrommed with hond-held transmitters
from existing equipment.
Vou must first program the HomeLink<!> trans-
mitter before you can use the system
~
page 90, Pragramming the HameLink<!>
tronsmitter.
HomeLink®
UniversaL remote
controL
General information
In order to program the HomeLink® transmit-
ter for devices utilizing rolling code, a second
person on a ladder who can safely reach the
garage door opener motor is recommended.
It is also necessary to locate the "learn" but-
ton on your garage door opener motor. Refer
to the operating instructions for the opener,
as the location and color ofthis button may
vary by manufacturer.
Vou can still use the original remote control
for the device at any time.
b
Hide quick links:
Advertisement
Table of Contents
