Bulbs - Audi TT 2012 Owner's Manual

For your safety, we recommend that you have
your authorized Audi dealer replace burned
out bulbs for yau.
Fuses and bulbs 2:
- If you must replace the light bulbs your-
self, always remember that the engine
compartment of any vehicle is a hazard-
ous area to work in. Always read and
heed aU WARNINGS
q
page 176, Engine
compartment
q
A.
- It is best to ask your authorized Audi
dealer whenever you need to change a
bulb.
- Changing Xenon lamps requires the spe-
cial training, instructions and equip-
ment.
- Only an authorized Audi dealer or other
qualified workshop should change the
bulbs in gas discharge lamps.
&..
WARNING
There are parts with sharp edges on the
openings and on the bulb holders that can
cause serious cuts.
- Ifyou are uncertain about what to do,
have the work performed by an author-
. ized Audi dealer or other qualified work-
shop. Serious personal injury may result
from improperly performed work.
[ijj
Tips
1
10
Amps
5
No. Equipment
11 Feed (brake pedal)
Activated charcoal filter/charge
12
pressure control valve
Replacing light bulbs
For your safety, we recommend that you have
your authorized Audi dealer replace any bulbs
for you, since your dealer has the proper tools,
the correct bulbs and the expertise.
Gas discharge lamps (Xenon lights)*:
Due to the high electrical voltage, have the
bulbs replaced bya qualified technician.
Headlights with Xenon light can be identified
by the high voltage sticker.
A
WARNING
Contact with high-voltage components of
the electrical system and improper re-
placement of gas discharge (Xenon) head-
light bulbs can cause serious personal in-
jury and death.
- Xenon bulbs are pressurized and can ex·
plode when being changed.
BuLbs
It is becoming increasingly more and more
difficult to replace vehicle light bulbs since in
many cases, other parts of the car mustfirst
be removed before you are able to get to the
bulb. This applies especiaUy to the light bulbs
in the front of your car which you can only
reach through the engine compartment.
Sheet metal and bulb holders can have sharp
edges that can cause serious cuts, and parts
must be correctly taken apart and then prop-
erly put back together to help prevent break-
age of parts and long term damage from wa-
ter that can enter housings that have not been
properly resealed.
No. Equipment
Amps
Fuse holder (black)
1 Not used
2 Not used
3 Not used
4 Not used
Anti-theft warning system (sen-
S
sor), anti-theft warning system
5
(horn)
6
Headlamp washer system 30
Electric fuel pumps (supply),
7
volume control valve/Interrelais 15/10
(5-cyl.)
8
Windshield wipers 30
9
Heated seats (driver and pas-
25
senger)
10
Lumbar support (driver and
10
passenger)
11 Not used
12 Ventilation blower 40
Fuse holder (brown)
Not used
'"-
Electric fuel pump (s'cyl.)
30
Not used
Relay coil relay volume control
5 valve (4-cyl.}/02 sensors (5-
5/10
cyl.)
6
02 sensors
10
7
Positioning valves pre-wired en-
10
gine harness
8 Ignition coils
20
9
Engine (control unit)
25
10 Water pump delayed-off
10
~
Note that the foUowing table is accu rate at
the time of going ta press and is subject ta
change.
Some of the equipment itemslisted are op-
tional or only available on certain model con-
fig urations.
Fuse location, left side of engine
compartment
232
Fuses and bulbs
No. Equipment
Amps
24 Transmission (control unit)
15
25
Heater rear window Coupe/
30/20
heated rear window Roadster
26 Driver's side power window 30
27 Passenger's side power window 30
28 Not used
29 Washer pump 15
30 Cigarette lighter 20
31 Starter
40
32 Steering column module 5
33 Instrument cluster 5
34 Radio navigation system, radio 20/1S
35 Audio amplifier 30
36 Engine (control unit) 10
37 CAN (Gateway) 5
38 Cigarette lighter 20
39 Not used
40 Not used
41 Not used
42 Not used
43 Not used
44 Not used
45 Not used
46 Not used
47
SDARs tu ner, ceU phone pack-
S
age, TV tuner
48 VDA interface
5
49 Not used
Fig. 176 Illustration of fuse holder on left side of en-
gine compartment: fuses (without fuse caver)