Clear Vision; Lights - Audi TT 2012 Owner's Manual

44 Opening and closing
--
Clear vision
Fig. 44 Instrument panel: light switch
Light Sensor Malfunction*
In the event of a light sensor malfunction, the
driver is notified in the instrument cluster dis-
play:
g
Automatic headlights/automatic wipers
defective
For safety reasons the low beams are turned
on permanently with the switch in AUTO'.
However, you can continue to turn the lights
on and off using the light switch. Have the
~
Automatic headlight control*
In the switch position AUTO the automatic
headlight control is turned on. The low
beams are turned on automatically through a
light sensor as soon as ambient brightness
(e.g. when driving into a tunnel) falls below a
value preset at the factory. When ambient
brightness increases again, the low beams are
turned off again automatically
q.&..
In the AUTO position the low beams are
switched off automatically when the ignition
is turned off.
Daytime running lights (Canada models
only)
The daytime running lights are activated only
when the light switch
q
fig. 44 is either at the
a
or the
,00:
position.
The daytime running lights function cannot be
turned off.
Daytime running lights (DRL) (USA
models)
The daytime running lights are activated only
when the light switch is at the AUTO' or DRL*
position.
lights will go off and only the side marker
lights will be on.
The daytime running lights can be turned on
or off using this function. If the function is ac-
tive, the daytime running lights are turned on
automatically when the ignition is switched
on.
'"
'"
'"
~
al
.. Turn the light switch to
~D.
.. Push the high beam lever forward towards
the instrument panel
q
page 47.
Switching off the lights
.. Turn the light switch to O.
The headlights only work when the ignition is
Switched on. While starting the engine or
when switching off the ignition, the head-
switching the headlights on and off
Fig.4S Instrument panel: light switch with daytime
running lights (DRL)
.. Turn the light switch to AUTO*
q
fig. 44 .
Switching on the headlights and high
beam
Switching on the side marker lights
.. Turn the light switch to
,00:.
Switching on automatic headlight
control*
The lig ht switch must not be overtu rned past
the stops in either direction.
CLear vision
Lights
Opening the windows
.. Insert the key into the lock of the driver's
door.
.. Turn and hold the key in the open position
@.
Reactivating the system after battery
1
disconnection
Reactivating the convenience close/open fea-
ture
A
WARNING
- Be careful when closing the windows.
Check to see that no one is in the way, or
serious injury could result!
- Always read and heed WARNING
q.&.
in
General description on page 38.
The automatic close function will cease if the
key is released.
If the vehicle battery is disconnected and then
reconnected, the automatic closing and open-
ing function will not work until it is reactivat-
ed. To reactivate this feature, perform the fol-
lowing steps:
Reactivating close/open feature
.. Pull and hold the power window switch un-
til the window is completely closed.
.. Release the switch.
.. Pull the switch again-for one second. The
automatic closing/openin'§ is now reactivat-
ed.
opened are the power windows switched
off.
- Be careful when closing the windows.
Check to see that no one is in the way, or
serious injury could result!
- Always remove the ignition key whenever
you leave your vehicle.
- If you lock your vehicle from the outside,
no one, especially children, should re-
main in the vehicle.
- Do not stick anything on the windows or
the windshield that may interfere with
the driver's field of vision.
Convenience close/open feature
(D
Tips
- When the doors are opened, the win-
dows are automatically lowered 10 mm.
- The windows can still be opened and
closed for about ten minutes after the
ignition has been turned off. The power
windows are not shut off until one of the
front doors is opened.
You con close or open the windows trom out-
side when you tock or untock your cor with the
key.
Fig. 43 Key turns for opening and closing
Closing the windows
.. Insert the key into the lock of the driver's
door.
.. Make sure that the windows are not blocked
q.&..
.. Turn and hold the key in the lock position
®
q
fig.
43 until the windows are completely
closed.
>