Panel (Control And Display Panel) - ABB DCS 600 Manual

For selecting and adjusting
all parameters and signals.
0 L
B…‚ˆƒ
17 RAMP GENERATOR
hqÁ h€r
08 ACCEL 1
Tˆit…‚ˆƒ
hqÁ h€r
20.0 s
Whyˆr
Selects the display of feedback values plus the
signal group and the error memory group.
D9Áˆ€ir…à 8‚‡…‚y Tƒrrq
y‚ph‡v‚ …rsr…rpr
‚sÇur
GÃ2Ãy‚phy …ƒ€
q…v‰r
ÃÃÃ2Ã…r€‚‡r
†ryrp‡rq
0 L
T‡h‡ˆ†Ã…‚
SPEEED ACT
6p‡ˆhyÆvthy
CONV CUR
h€rÃhqÉhyˆr
U ARM ACT
8ˆ…†‚…Æu‚†
‡urÃ…‚Ã†ryrp‡rq
are used to change the group. In the parameter and
reference presetting modes, you can alter the param-
eter value or the reference setting ten times faster by
means of the twin arrow keys than by means of the
is used to select local (control
Error acknowledgement key.
Ã2Ãyh†‡Ãshˆy‡
0 L
!Ã2Ãyh†‡iˆ‡‚rÃshˆy‡
1 LAST FAULT
((Ã2Ãyh†‡iˆ‡('ÃÃshˆy‡
Ih€rÂsÃAhˆy‡Ã
Emergency stop
‚…Ãhyh…€
3212:59:35:56
U‚‡hyÇv€rÃhs‡r…
†v‡pu‚Ã
CCCC)HH)TT††
in local mode switches the main contactor on.

Panel (control and display panel)

Parameters
0,0 rpm 00
Actual
SˆÃ†‡h‡ˆ†
HhvÃp‚‡hp‡‚…
†‡h‡ˆ† Ã2ÃSˆ
Ã2ƒr Ã2ÃT‡‚ ƒ
Ã2Ãpy‚†rq
0,0 rpm 00
0,0 rpm
0 A
0 V
Twin arrow keys
single arrow key.
Local/Remote
panel) or remote control.
Reset
0,0 rpm 00
On
Fig. 2.5/8: Function keys and various displays on the removable
control and display panel. The panel can also be used to load the
same program on different power converters.
II F 2-12
Equipment
Function
Selects the "functions" operating mode; can be used
to perform special functions such as uploading and
downloading or application programming.
0 L
T‡h‡ˆ†Ã…‚
UPLOAD
Aˆp‡v‚†Ã‡‚ÃirÃ
DOWNLOAD
†ryrp‡rq
CONTRAST
9v†ƒyh’Ãp‚‡…h†‡
†r‡‡vt
Drive
for subsequent extensions
Enter
is used in the following modes:
Parameter setting: enter new parameter value
Feedback value
signal display: enter the current signal selec-
tion mode
Signal selection: accept selection and return to
the feedback value signal dis-
play mode
Arrow keys
are used to select parameters within a group. You al-
ter the parameter value or the reference setting in
the parameter and reference presetting modes. In
the feedback signal display mode, you select the line
you want.
Start
starts the drive in local mode.
Stop
shuts the drive down if you are in local mode.
Reference
is used to activate the reference presetting mode.
Off
in local mode switches the main contactor off.
0,0 rpm 00
<==
==>