Mali Racing desertfighter 2 3015 User Manual page 36

Sensored/Sensorless ESC's Indicating LED
Status of the function
low voltage of the battery
Over-heat of the ESC and motor (95°)
Sensored motor
Sensorless motor
Sensorless ESC's Indicating LED
Status of the function
Low voltage of the battery
Over-heat of the ESC and motor (95°)
Sensorless motor
Throttle Range Calibration
(For the first time using transmitter or changing the transmitter you must set Throttle Range Calibration)
1. Switch OFF the ESC, then connect the battery pack and turn ON the transmitter; set the direction of the throttle
channel to REV; set the EPA/ATV value of the throttle channel to 100%.
2. Hold the "Set" button and switch ON the ESC, wait for about 4 seconds until the Orange LED is on solid, then
release the "Set" button, pull the throttle trigger to full throttle until Red LED is on Solid and the motor beeps.
3. Push the throttle trigger to Full Brake until the Orange LED blinks and will be on solid, the motor beeps.
4. Return the throttle trigger to the Neutral position, both of the Red LED and Orange LED blink simultaneously
and will be on solid, the motor beeps, both of Red LED and Orange LED wink. The Throttle Range Calibration is
confirmed.
5. Turn OFF the ESC power switch.
6. Turn the ESC back ON. You are ready to use the ESC now.
Programmable items and default settings
Default settings are shown in the grey boxes
Programmable
Items
1
Cut-off Voltage 2.6V/cell
Running Mode Forward
w/o
Reverse
Motor timing Very
Low
Initial Acceleration Low
Throttle Percent 20%
Reverse
Throttle Limit 0%
Percentage Braking 10%
Percentage Drag 0%
Brake
Motor Rotation Normal
Neutral Range 2%
I-power pro sensored/sensorless brushless esc general information
1. Cutoff Voltage
• Automatically detect the number of the cells
According to the type of your batteries , set up the type of the batteries and Low Voltage Cutoff Threshold via PC
software or program card. The ESC can detect the Voltage of the battery anytime and will stop working once the
Voltage of the battery is lower than the preset Low Voltage Cutoff Threshold.
• When using NiMH or NiCd batteries you do not need to set a cutoff voltage to protect the batteries. If you are
using more than 6-cell NiMH or NiCd batteries, you must adjust the cutoff voltage, for example if you are using
an 8-cell pack of NiMH batteries you would use a cutoff of 5.6V volts (8 x 0.7V = 5.6V). When the voltage of the
batteries packs is within 8.4 ~ 1 2.6V, the ESC will automatically identify 3S LiPos. When the voltage of the batteries
packs is less than 8.4V, the ESC will automatically identify 2S LiPos. When the voltage of the batteries packs is
36
MALI CARS MANUAL 2013 V2.indd 36
Indicated led Status of the led
Red LED
Orange LED
Red and Orange LED
Orange LED
Indicated led Status of the led
Red LED
Orange LED
Orange LED
Programmable Value
2 3 4 5
2.8V/cell 3.0V/cell 3.2V/cell 3.4V/cell
Forward Foward
with /
pause Reverse
then
Reverse
Low Normal High Very
High
Medium High Very
High
30% 40% 50% 60%
20% 30% 40% 50%
20% 30% 40% 50%
4% 8% 12% 15%
Reverse
3% 4% 5% 6%
Blinking
Blinking
ON
ON
Blinking
Blinking
ON
6 7 8 9
No
cut-off
70% 80% 90% 100%
60% 70% 80% 90%
60% 70% 80% 100%
20% 25% 30%
10%
19/03/13 14:35