Can-Am spyder gs 2008 Operator's Manual
  1. Manuals
  2. Brands
  3. Can-Am Manuals
  4. Offroad Vehicle
  5. spyder gs 2008
  6. Operator's manual

Can-Am spyder gs 2008 Operator's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

WARNING
Learn how the Spyder roadster is different.
Read this operator’s guide and watch the safety video.
Complete a training course (if available), practice and become proficient with the controls.
Consult local laws - license requirements vary by location.
Keep this guide in the front storage compartment.
2 1 9
0 0 0
5 3 6

Advertisement

Table of Contents
loading

Related Manuals for Can-Am spyder gs 2008

Summary of Contents for Can-Am spyder gs 2008

  • Page 1 WARNING Learn how the Spyder roadster is different. Read this operator’s guide and watch the safety video. Complete a training course (if available), practice and become proficient with the controls. Consult local laws - license requirements vary by location. Keep this guide in the front storage compartment. 2 1 9 0 0 0 5 3 6...
  • Page 2 CALIFORNIA PROPOSITION 65 WARNING WARNING This product contains or emits chemicals known to the state of California to cause cancer and birth defects or other reproductive harm. ®™ and the BRP logo are trademarks of Bombardier Recreational Products Inc. or its affiliates. ©...

  • Page 3: How To Use This Operator's Guide

    ENT ABOUT THE SPYDER ROAD- If possible, take a training class STER (p.28). that is specifically designed for the Spyder roadster. Check our website In this Operator’s Guide, the word at www.can-am.brp.com for more motorcycle typically refers information about upcoming training two-wheeled motorcycle.

  • Page 4: Table Of Contents

    TABLE OF CONTENTS HOW TO USE THIS OPERATOR’S GUIDE ........1 Know Before You Go ..
  • Page 5 TABLE OF CONTENTS UNDERSTANDING RISK ON THE ROAD ........32 Type of Vehicle ..............32 Operator Skills and Judgment.
  • Page 6 WARRANTY BRP LIMITED WARRANTY – USA AND CANADA: 2008 CAN-AM™ SPYDER™ ROADSTER ................ 112...
  • Page 7 TABLE OF CONTENTS BRP LIMITED WARRANTY OUTSIDE USA AND CANADA: 2008 CAN-AM SPYDER ROADSTER ............116 CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT .

  • Page 8: General Precautions

    GENERAL PRECAUTIONS Avoid Carbon Monoxide – Never top off the fuel tank. Leave some room for the fuel to expand Poisoning with temperature changes. All engine exhaust contains carbon – Wipe up any spilled fuel. monoxide, a deadly gas. Breathing car- –...
  • Page 9 GENERAL PRECAUTIONS See your authorized Can-Am roadster dealer for available accessories for your vehicle. ______________________...
  • Page 10 GENERAL PRECAUTIONS _______________________...

  • Page 11: Controls, Instruments And Basic Procedures

    CONTROLS, INSTRUMENTS AND BASIC PROCEDURES ______________________...

  • Page 12: Operating During Break-In

    After the break-in period, your vehicle should be inspected by an authorized Can-Am roadster dealer as per the MAINTENANCE SCHEDULE (p.72). NOTE: The break-in inspection is per- formed at the expense of the vehicle owner.

  • Page 13: Controls/Instruments

    CONTROLS/INSTRUMENTS Many controls are similar to the controls of a motorcycle, but some controls are dif- ferent. It is important to know the location and operation of all controls, and to de- velop and practice smooth and coordinated use of them. See REQUIRED RIDING SKILLS AND PRACTICE EXERCISES (p.
  • Page 14 CONTROLS/INSTRUMENTS To decrease engine speed, roll the 4) Gearshift Lever throttle away from you. The gearshift lever is in front of the left footrest. The gear pattern is Reverse-1-Neutral- 2-3-4-5. rmo2008-001-007_b TO DECREASE SPEED The throttle is spring loaded and should return to idle when you release your grip.
  • Page 15 CONTROLS/INSTRUMENTS locks to apply the parking brake. Firm- ly press the pedal down a second time to release the parking brake. rmo2008-001-079_a 1. Parking brake pedal rmo2008-001-080_a 1. Engaging/disengaging parking brake pedal WARNING Do not use the parking brake to slow or stop the vehicle;...

  • Page 16: Secondary Controls

    CONTROLS/INSTRUMENTS Secondary Controls rmo2008-001-001_a Ignition switch Turn signal button Engine start button Horn button Engine stop switch Reverse interlock lever Hazard warning switch Headlights override button Headlights switch 1) Ignition Switch – seat opening mechanism to access: • fuel tank cap •...
  • Page 17 6) Turn Signal Button to have another one made by an autho- rized Can-Am roadster dealer. The turn signal button is located near the left handgrip. It turns off automat- 2) Engine Start Button...

  • Page 18: Multifunction Gauge Cluster

    CONTROLS/INSTRUMENTS 9) Headlight Override The button can be used to light up in- side the front storage compartment. There is a headlight override button on The high beams will reflect on the the front of the right handgrip. Push inside of compartment lid when it is and hold the headlight override button opened.
  • Page 19 CONTROLS/INSTRUMENTS 5) Indicator Lamps Indicator lamps will inform you of various conditions or problems. An indicator lamp can flash alone or in combination with another lamp. The digital display provides a brief description for some of the conditions or prob- lems indicated by lamps.
  • Page 20 CONTROLS/INSTRUMENTS The gearbox positions are: R (reverse), 1, N (neutral), 2, 3, 4, 5. 10) Engine Temperature Bar gauge that continuously indicates the engine coolant temperature. 11) Digital Speedometer In addition of the analog type speedometer, vehicle speed can also be indicated via this display.
  • Page 21 5. Press SET (S) button to change hour. 6. Press MODE (M) button to switch to minute (minute flashes). 7. Press SET (S) button to change minute. 8. Press MODE (M) button. Setting Language For display language setting, refer to an authorized Can-Am roadster dealer. _____________________...

  • Page 22: Basic Procedures

    BASIC PROCEDURES Starting and Stopping the NOTICE Do not apply throttle while starting the engine. Engine 9. Check the display for problems and Starting the Engine to ensure that the oil light turns off. 10. Release the parking brake. Make WARNING sure the parking brake indicator on Exhaust gas contains poisonous...

  • Page 23: Adjusting Mirrors

    BASIC PROCEDURES 2. Shift the transmission into NEU- TRAL. 3. Disengage the parking brake. 4. Dismount on the right side of the vehicle, keeping your foot on the brake pedal. 5. Push the vehicle, using the brake as needed. CAUTION Only push from the right-hand side, so you can reach the rmo2008-001-074_a brake pedal.

  • Page 24: Opening The Seat

    BASIC PROCEDURES Fueling Fuel Recommendation Use unleaded gasoline or oxygenat- ed fuel containing no more than 10% ethanol or methanol or both. The gaso- line used must have the following min- imum octane number: MINIMUM OCTANE NUMBER Inside North America 87 ((R+M)/2) rmo2008-001-010 FRONT STORAGE COMPARTMENT...

  • Page 25: Operating In Reverse

    BASIC PROCEDURES Operating in Reverse 1. Check that the area behind you is clear, and continue to look back- wards while you ease out the clutch. Slow and stop using clutch and brake, just like when operating normally. 2. Keep your speed low and do not rmo2008-001-016 back up for long distances.
  • Page 26 BASIC PROCEDURES 3. Install a jack under the rear portion of frame. NOTICE Do not jack the vehicle un- der the rear shock. rmr2008-029-002 FRONT SUSPENSION ADJUSTING WRENCH 4. Lift the rear of vehicle until the shock absorber is fully extended. 5.

  • Page 27: License Plate Installation

    BASIC PROCEDURES rmo2008-002-009 rmr2008-030-004_c DAMPING PAD (P/N 293 740 028) A. Smooth adjustment (position 1) B. Hard adjustment (position 7) Refer to the following procedure for proper installation. NOTE: Never adjust the rear shock absorber cam from position 7 directly 1.
  • Page 28 BASIC PROCEDURES rmo2008-002-010_b TYPICAL 1. Existing hardware 5. Squeeze license plate and support together at each lower corner. ______________________...

  • Page 29: Safe Operating Instructions

    SAFE OPERATING INSTRUCTIONS _________ ________ SAFE OPERATING INSTRUCTIONS...

  • Page 30: What's Different About The Spyder Roadster

    WHAT’S DIFFERENT ABOUT THE SPYDER ROADSTER The Spyder roadster is a different type vehicles behind you that may not be of road vehicle. This section will help able to stop as quickly. you understand some of the vehicle’s distinctive features and operating char- Antilock Braking System (ABS) acteristics.

  • Page 31: Width

    WHAT’S DIFFERENT ABOUT THE SPYDER ROADSTER Width – Shift back into first gear before shut- ting off the engine. Because the Spyder roadster is wider than a typical motorcycle: Driver’s License and Local – Keep the front wheels in your lane Laws during turns.

  • Page 32: Driving Aid Technologies

    – a Stability Control System (SCS) which can be ordered only from an au- is designed to limit the power driv- thorized Can-Am roadster dealer. ing the rear tire and to brake individ- ual wheels, which reduces the risk Proper tire inflation pressure and tread...

  • Page 33: Electronic Brake Distribution (Ebd)

    DRIVING AID TECHNOLOGIES the vehicle from entering a turn too fast. If you drive too fast for condi- tions, you can lose control, even with VSS. Electronic Brake Distribution (EBD) The Spyder roadster is equipped with an Electronic Brake Distribution (EBD) system.

  • Page 34: Understanding Risk On The Road

    UNDERSTANDING RISK ON THE ROAD Before you operate the Spyder road- who develop good skills will have bet- ster, consider your risk of being hurt or ter control of their vehicle. Don’t rely killed in a crash, how you can reduce on your experience with motorcycles, the risk and whether you are willing to automobiles, ATVs, snowmobiles or...

  • Page 35: Vehicle Condition

    UNDERSTANDING RISK ON THE ROAD your judgment and skills are impaired by any alcohol consumption. You must be physically able to oper- ate all controls, turn the handlebars through the full range of steering, mount and dismount, and monitor your surroundings to operate the vehicle.

  • Page 36: Riding Gear

    RIDING GEAR Riding three-wheeled, open-air vehi- with the back of the operator’s helmet. cles like the Spyder roadster requires Even the best helmet is no guarantee the same protective gear as motorcy- against injury, but statistics indicate cling. Even though the vehicle is more that helmet use significantly reduces stable at low speeds than a motorcy- the risk of brain injury.
  • Page 37 RIDING GEAR Gloves Leather is a good choice because it is durable and wind-resistant and pro- Full-fingered gloves protect hands vides protection against injury. Oth- from the wind, sun, heat, cold and er abrasive-resistant protective gear flying objects. Gloves that fit snugly made of synthetic fabrics are good will improve grip on the handlebars choices, too.
  • Page 38 RIDING GEAR be much more comfortable and alert than a rider who is wet and cold. One- or two-piece styles are available, and those designed specifically for motorcycling are best. High-visibility orange or yellow colors are good choic- es. A feature to look for is elastic in the waist, pant legs and sleeves.

  • Page 39: Required Riding Skills And Practice Exercises

    REQUIRED RIDING SKILLS AND PRACTICE EXERCISES Before you take the Spyder roadster Keep this basic parking lot diagram in on the road, you need to develop rid- mind when setting up the exercises. ing skills and strategies for managing 3 m (10 ft) wide parking lot spaces are risk on the road.

  • Page 40: Preparing To Ride

    REQUIRED RIDING SKILLS AND PRACTICE EXERCISES and rear before doing an exercise. Al- – Become familiar with using the en- so, watch out for children and animals. gine stop switch. Directions Preparing to Ride – With the vehicle in NEUTRAL and Know the location and operation of all the parking brake engaged, pull in the vehicle’s controls (p.
  • Page 41 REQUIRED RIDING SKILLS AND PRACTICE EXERCISES Directions 3) Engine Stop while in Motion Purpose For this exercise, do NOT use any throttle. You will be controlling your – Become familiar with using the en- movement using only the clutch in the gine stop switch when in motion so friction zone and brake.
  • Page 42 REQUIRED RIDING SKILLS AND PRACTICE EXERCISES 4) Using the Throttle Purpose – Become familiar with operating the throttle. – Learn to balance throttle and clutch. Directions This exercise is similar to the friction zone exercise, except this time you will be using some throttle. You will use the entire straightaway, stopping only at the ends.
  • Page 43 REQUIRED RIDING SKILLS AND PRACTICE EXERCISES on the vehicle. You will need to exert more force to turn the handlebar of your vehicle than is needed to turn a motorcycle. However, it is easier to stop while turning than with a motor- cycle.
  • Page 44 REQUIRED RIDING SKILLS AND PRACTICE EXERCISES Directions you maintain steering control while ap- plying the maximum braking force. 6 m (20 ft) Weave – Start at one end of the straight away – Weave between every marker/ and accelerate to 8 km/h (5 MPH). intersection of every other park- Partway down the straightaway, ing spot.
  • Page 45 REQUIRED RIDING SKILLS AND PRACTICE EXERCISES Purpose – Become familiar with the foot mo- tions needed to shift gears. – Learn to upshift and downshift. Directions This exercise is similar to what you did before, except now you will be upshift- ing on the straightaways, then coming to a stop at the end of each straight- away.
  • Page 46 REQUIRED RIDING SKILLS AND PRACTICE EXERCISES • You do not need to apply throttle, – Roll off the throttle and pull in the but once you are comfortable, if clutch lever. space allows, you can adjust the – Step on the shift lever to shift into throttle to increase speed in sec- first gear.

  • Page 47: Developing Advanced Riding Skills

    REQUIRED RIDING SKILLS AND PRACTICE EXERCISES 9) Swerve 10) Operating in Reverse Purpose Purpose – Become familiar with the vehicle’s – Become familiar with the vehicle’s handling for quick maneuvers. handling and turning radius in re- verse. – Try different variations of braking and swerving.
  • Page 48 REQUIRED RIDING SKILLS AND PRACTICE EXERCISES advanced skills. First, learn the ”Street Strategies” covered in the next sec- tion. Then you can take the vehicle on the road in relatively low-risk situa- tions. Start by riding in less challenging situa- tions: –...

  • Page 49: Street Strategies

    STREET STRATEGIES This section provides some strategies braking distance is longer on slippery to reduce your risk on the road. Many road surfaces, down hills, or when car- of these strategies are similar to those rying more weight, and visibility may used for motorcycles.

  • Page 50: Being Visible

    STREET STRATEGIES When braking, be particularly aware of signals, but they may not cancel after vehicles behind you that may not be shallow turns. Make sure turn signals able to stop as quickly as the Spyder are off after you have completed your roadster.

  • Page 51: Lane Position

    STREET STRATEGIES Time of Day and Weather for drivers ahead to see you, you must be able to see their mirrors. When you In dim light, such as at night, at dawn are being followed by a large vehicle, or dusk, or in poor weather such as rain passing vehicles may not be able to or fog, you may be harder to see.
  • Page 52 STREET STRATEGIES are preparing to turn. This can make Turns you more visible and discourage other Remember to slow, look, and steer motorists from trying to drive around through turns. you. Watch for vehicles approaching – Slow: Reduce speed as needed be- from behind.
  • Page 53 STREET STRATEGIES When shifting gears while turning, be help maintain enough power. Going careful not to release the clutch lever down hills, a lower gear can provide too fast. Adjust throttle as you release engine braking to control your speed. the clutch lever to match engine and To start while on an incline, hold the vehicle speed in a smooth shift.

  • Page 54: Road Conditions And Hazards

    STREET STRATEGIES Particularly on curvy roads, Spyder Avoid large water puddles or water roadster riders might become tired streams, and slow down or pull off the sooner than motorcyclists. Don’t push road during heavy rains. If you must yourself to keep up with motorcycles; pass through water, slow down as stop if you are tired.

  • Page 55: On-Road Emergencies

    (p. 68) to the near- if necessary. est Can-Am roadster dealer to have If you strike a large enough obstacle, it thoroughly inspected for safety bump or hole, the impact can make the before riding again.

  • Page 56: Carrying A Passenger Or Cargo

    CARRYING A PASSENGER OR CARGO Weight Limits 4. The Spyder roadster may be less stable. There is a greater risk of Do not exceed the weight limits for rid- tipping or rolling during extreme ers and cargo. maneuvers with weight that is higher or farther to the rear (like WEIGHT LIMITS a passenger).

  • Page 57: Where To Store Cargo

    CARRYING A PASSENGER OR CARGO Instruct the passenger on how to ride Avoid abrupt acceleration, braking and before starting out. Have the passen- turns, especially with inexperienced ger follow these rules: passengers. Sudden, unexpected ma- neuvers can make the passenger fall 1.

  • Page 58: Knowledge Self-Test

    You should only replace the tires should make it common practice with those approved by BRP to brake and turn at the same obtained from an authorized time. Can-Am roadster dealer. True False True False 12. Under normal conditions, It is important for the passenger to following distance should be be alert and sober.
  • Page 59 KNOWLEDGE SELF-TEST 14. List 5 ways of being more noticeable to other drivers. 1) _________________________ 2) _________________________ 3) _________________________ 4) _________________________ 5) _________________________ 15. When braking on surfaces with less than ideal traction, you should pump the brakes to help maintain control of the vehicle.

  • Page 60: Answers

    KNOWLEDGE SELF-TEST Answers 12. b. 2 seconds Under normal conditions, following distance should be False at least two seconds. To stop quickly, press the brake 13. True pedal only. Never use the parking brake while the vehicle is moving. 14. 1) Make sure your lights and False reflectors are clean.

  • Page 61: Safety Information On The Vehicle

    SAFETY INFORMATION ON THE VEHICLE This vehicle comes with a hang tag and labels containing important safety informa- tion. Any person who rides this vehicle should read and understand this information on the vehicle before riding. Hang Tag rmo2008-001-102 Safety Card The Safety Card is found at the top of the multifunction gauge cluster.

  • Page 62: Labels

    The following labels are on your vehicle, and they should be considered permanent parts of the vehicle. If missing or damaged, they can be replaced free of charge. See an authorized Can-Am roadster dealer. NOTE: The following illustrations used in this Operator's Guide are a general rep- resentation only.
  • Page 63 SAFETY INFORMATION ON THE VEHICLE Label 1 TIRE INFORMATION rmo2008-001-092_en rmo2008-001-029_b 1. Label 1 location Label 2 Label 3 rmo2008-001-098_en rmo2008-001-093_en rmo2008-001-107_b 1. Label 2 location rmo2008-001-031_c 1. Label 3 located in the front storage compartment _________ ________ SAFE OPERATING INSTRUCTIONS...
  • Page 64 SAFETY INFORMATION ON THE VEHICLE Label 4 Label 6 WARNING Clean filler cap before removing. Use only DOT 4 brake fluid from a sealed container. rmo2008-003-006_en rmo2008-001-040_b 1. Label 6 located underneath seat rmo2008-001-029_c 1. Label 4 located on the oil reservoir behind the left middle side panel Label 5 rmo2008-003-003...

  • Page 65: Reporting Safety Defects

    REPORTING SAFETY DEFECTS Your safety is very important to Bombardier Recreational Products Inc. (BRP). If you have any concerns you should immediately contact BRP’s customer service. In the USA, if you believe that your ve- hicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the Na- tional Highway Traffic Safety Adminis-...
  • Page 66 REPORTING SAFETY DEFECTS ________ ________ SAFE OPERATING INSTRUCTIONS...

  • Page 67: Pre-Ride Inspection

    PRE-RIDE INSPECTION _____________________...

  • Page 68: Pre-Ride Checklist

    See an authorized – Lights: Check operation of head- Can-Am roadster dealer as neces- lights, tail light, brake light, turn sig- sary. nals and hazard warning lights.

  • Page 69: Transporting And Storing

    TRANSPORTING AND STORING _____________________...

  • Page 70: Transporting The Spyder Roadster

    TRANSPORTING THE SPYDER ROADSTER If your vehicle needs to be transported, 4. Attach the straps to the winch ca- it should be carried on a flatbed trailer ble. If possible, use chains or addi- of the proper size and capacity. tional straps to attach the straps to the winch cable as indicated below to avoid damaging the bumper cov-...
  • Page 71 TRANSPORTING THE SPYDER ROADSTER rmo2008-001-067_a REAR WHEEL ATTACHMENT 1. Tie-down strap rmo2008-001-069_a 2. Inside rear wheel rim ONLY FRONT WHEELS ATTACHMENT – METHOD 1 1. Strap around the rim of each front wheel 11. Firmly attach the rear wheel and attached to the front of trailer tie-down strap to the rear of the trailer with a ratchet.

  • Page 72: Storing The Spyder Roadster

    2. Charge the battery if needed BRP recommends you have your au- (p.87). thorized Can-Am roadster dealer fully 3. Perform a pre-ride inspection prepare your vehicle for storage. Or, at (p.66), then test-ride the vehicle your convenience, you can follow the at low speed.

  • Page 73: Maintenance

    MAINTENANCE _____________________...

  • Page 74: Maintenance Schedule

    If not, see your authorized Can-Am roadster dealer. Other important items in the maintenance schedule that are more difficult and re- quire special tools are best performed by your authorized Can-Am roadster dealer. WARNING Turn off the engine and follow these maintenance procedures when per- forming maintenance.
  • Page 75 PERIODIC MAINTENANCE SCHEDULE C: CLEAN INITIAL INSPECTION 1 000 km (600 mi) I: INSPECT AND/OR (To be performed by an authorized Can-Am roadster dealer. ADJUST as required The initial maintenance is very important and must not be neglected.) L: LUBRICATE...
  • Page 76 PERIODIC MAINTENANCE SCHEDULE C: CLEAN INITIAL INSPECTION 1 000 km (600 mi) I: INSPECT AND/OR (To be performed by an authorized Can-Am roadster dealer. ADJUST as required The initial maintenance is very important and must not be neglected.) L: LUBRICATE...
  • Page 77 PERIODIC MAINTENANCE SCHEDULE C: CLEAN INITIAL INSPECTION 1 000 km (600 mi) I: INSPECT AND/OR (To be performed by an authorized Can-Am roadster dealer. ADJUST as required The initial maintenance is very important and must not be neglected.) L: LUBRICATE...

  • Page 78: Maintenance Procedures

    MAINTENANCE PROCEDURES Tool Kit 12. front suspension adjusting wrench (not illustrated) (p. 23) The tool kit is located inside the front 13. towel (not illustrated). storage compartment, on the left-hand side of the vehicle. The tools marked with (*) are used only for procedures in the maintenance manual.
  • Page 79 MAINTENANCE PROCEDURES rmo2008-001-032_a rmo2008-001-033_b 1. Middle side panel clips Step 1: Press down top edge Step 2: Push top edge under top side panel’s 2. Press down panel’s top edge with edge both hands and pull out. 3. Secure panel by pushing and turn- ing each clip clockwise (1/4 turn) to its maximum rotation.
  • Page 80 MAINTENANCE PROCEDURES Installation 1. Screw 4 Torx screws. NOTICE Do not overtorque. Any deformation on the panel around the screw is an indication that it is too tight. You may damage the pan- rmo2008-001-078_a 3) Rear Side Panel 1. Flat head screwdriver under rivet 2.

  • Page 81: Tires

    If any of the above occurs, have the tire only the BRP recommended tires, repaired or replaced as soon as possi- which can be ordered only from an ble by an authorized Can-Am roadster authorized Can-Am roadster dealer. dealer. Tire Pressure...

  • Page 82: Drive Belt

    (5), have the belt properly tire’s center tread will wear unevenly aligned by an authorized Can-Am road- depending on if the vehicle is driven ster dealer as soon as possible. smoothly or aggressively.
  • Page 83 MAINTENANCE PROCEDURES Drive Belt Wear Inspect the drive belt with the vehicle in neutral, engine off, on a level surface with plenty of room – you will have to roll the vehicle forward or backward to see the full length of the belt. rmo2008-001-109_a DRIVE BELT SURFACES 1.

  • Page 84: Engine Oil And Coolant

    While riding, if you feel vibrations in the belt or if the belt is skipping sprocket teeth, have the belt tension adjusted as soon as possible by an authorized Can-Am roadster dealer. Engine Oil and Coolant rmo2008-001-017_a NOTICE The procedures for check- 1.
  • Page 85 MAINTENANCE PROCEDURES If the oil level is at the upper mark: 7. Remove the bottom plate under the oil reservoir. 13. Properly tighten the dipstick. 14. Install the left middle side panel (p. 77). Oil and Filter Replacement Change the engine oil and filter at the same time, and only when the engine is warm.
  • Page 86 – if debris are present, 24. Install a NEW O-ring on the oil filter see your authorized Can-Am road- cover. ster dealer. 25. Screw the oil filter cover in place.

  • Page 87: Brakes

    (P/N 219 700 362). quently requires coolant indicates leaks or engine problems. See an au- With the engine cold, check the thorized Can-Am roadster dealer. coolant level as follows: 1. Park the vehicle on a firm, level sur- Brakes face.

  • Page 88: Battery

    2. brake pedal for spongy feel 3. brake discs for excessive wear and surface condition 4. brake pads for wear, damage or looseness. See an authorized Can-Am roadster dealer if there are any problems with the brake system. rmo2008-001-040_b Battery 1.

  • Page 89: Clutch Fluid Level Verification

    The battery may need to be charged if the vehicle has not been ridden for at least one month. Always have the battery replaced by an authorized Can-Am roadster dealer. WARNING rmo2008-001-044_a 1. NEGATIVE (-) terminal Do not use conventional lead-acid 2.

  • Page 90: Headlights Aiming

    MAINTENANCE PROCEDURES The clutch fluid reservoir is near the re- WARNING verse interlock lever on the left handle- Avoid getting brake fluid on skin bar. or in eyes – it may cause severe Check the clutch fluid level as follows: burns.

  • Page 91: Vehicle Care

    MAINTENANCE PROCEDURES 5. Beam aiming is correct when the 2. Using a soft, clean cloth, wash the focus point (brightest spot) of the vehicle with water mixed with a headlight reflection is between the mild detergent, such as soap spe- marks.
  • Page 92 MAINTENANCE PROCEDURES ______________________...

  • Page 93: Road Side Repairs

    ROAD SIDE REPAIRS _____________________...

  • Page 94: Problems

    1. Move the other vehicle as close as Use your spare key to have another possible and preferably on the left one made by an authorized Can-Am side of the Spyder roadster. Make roadster dealer as soon as possible. If sure the vehicles are not touching.

  • Page 95: Electrical Accessories Failure

    NEGATIVE (-) jumper cable to the thorized Can-Am roadster dealer. NEGATIVE (-) terminal under the After recharging battery, have the vehi- seat of the Spyder roadster. cle inspected by an authorized Can-Am roadster dealer. Electrical Accessories Failure If any electrical accessories stop work- ing on the vehicle, check for blown fus- es and replace if necessary.
  • Page 96 PROBLEMS DESCRIPTION Accessories D.E.S.S. 10 A License plate light Position light Tail lights Service connector Ignition coil 15 A Fuel injectors Clock 10 A rmo2008-001-076_a Hazard warning lights 1. Fuse box located under the service cover Turn signal lights behind the front storage compartment 10 Fan 15 A Fuse Description...

  • Page 97: Light Failure

    If the light failure still occurs, have cover. the vehicle serviced by an authorized Can-Am roadster dealer. 5. Check whether the filament is melted. WARNING Always turn the ignition switch to the OFF position before replacing a bulb to avoid electric shock.
  • Page 98 PROBLEMS rmo2008-001-121_a 1. Upper console 2. Press on the screwdriver inside hole 3. Insert finger in opening 4. With the other hand, insert the rmo2008-001-084_a screwdriver in the other hole on LIGHTS LOCATION – FRONT OF VEHICLE the upper console. 1.
  • Page 99 PROBLEMS 8. Remove the bulb by releasing both clips with a small flat head screw- driver. rmo2008-001-103_a 1. Front turn signal lens screw 2. Turn the connector counterclock- wise as indicated below and re- move lens. rmo2008-001-124_a 1. Bulb housing 2.
  • Page 100 PROBLEMS 2. Remove the bulb by pushing in and turning counterclockwise. 3. Install the new bulb by pushing and turning it clockwise. 4. Reinstall the lens. Tail Light/Brake Light 1. Remove the panel under the pas- rmo2008-001-078_a senger seat by unscrewing 7 Torx 1.
  • Page 101 PROBLEMS rmo2008-001-118_a rmo2008-003-002_a 1. Connector 3. Turn the bulb holder clockwise and 7. Remove the bulb by pushing in and remove it from the connector. turning counterclockwise. 8. Install the new bulb by pushing and turning it clockwise. 9. Properly reinstall the parts in the re- verse order of their removal.

  • Page 102: Engine Does Not Start

    – Check to see whether the engine indicator lamp is ON while start- 3. Install the new bulb by pushing and ing. See an authorized Can-Am turning it clockwise. roadster dealer. 4. Reinstall the lens. Engine Does Not Start ENGINE DOES NOT TURN OVER 1.

  • Page 103: Messages In Multifunction Gauge Cluster

    Important information about vehicle condition is displayed on the multifunction gauge cluster. When starting the engine, always look at the gauge cluster for any special messages. If a problem persists, go to an authorized Can-Am roadster dealer. INDICATOR MAIN DIGITAL...
  • Page 104 *BRP recommends having the vehicle transported when in LIMP HOME. If you operate the vehicle in LIMP HOME, avoid abrupt maneuvers and immediately go to the nearest authorized Can-Am roadster dealer to have your vehicle serviced before riding again. In LIMP HOME, the engine RPM is limited and the vehicle speed is limited to 74 km/h (46 MPH).

  • Page 105: Technical Information

    TECHNICAL INFORMATION _____________________...

  • Page 106: Vehicle Identification

    These numbers are required by the authorized Can-Am roadster dealer to complete warranty claims properly. No warranty will be allowed by Bombardier Recreational Products Inc.

  • Page 107: Specifications

    SPECIFICATIONS MODEL SPYDER GS ENGINE ROTAX 990 60° V-Twin Engine type 4-stroke, Dual Over Head Camshaft (DOHC), liquid cooled Number of cylinders Number of valves 8 valves Bore 97 mm (3.82 in) Stroke 68 mm (2.68 in) Displacement 998 cm³ (60.90 in³) 10.7:1 Compression ratio Dry sump with separate oil reservoir...
  • Page 108 SPECIFICATIONS MODEL SPYDER GS ELECTRICAL SYSTEM Magneto generator output 500 W Ignition system type Electronic ignition with dual output coil Ignition timing Not adjustable Quantity NGK DCPR9E Spark plug Make and type (apply heat-sink paste P12 (P/N 420 897 186) on spark plug thread) 0.7 to 0.8 mm (.027 to .031 in) Engine RPM limiter setting Forward...
  • Page 109 SPECIFICATIONS MODEL SPYDER GS ELECTRICAL SYSTEM (cont’d) Camshaft position sensor (CAPS) Engine control module (ECM) Fuel pump 10 A O² heater Purge valve Starter solenoid D.E.S.S. License plate light Position light 10 A Tail lights Fuses under Service connector service cover Ignition coil 15 A Fuel injectors...
  • Page 110 SPECIFICATIONS MODEL SPYDER GS FUEL SYSTEM Multi-point Electronic Fuel Injection (EFI) Fuel Delivery Type with dual 57 mm throttle body Fuel pump Type Electrical module in fuel tank Idle speed 1400 ± 50 RPM (not adjustable) Type Regular unleaded gasoline Inside North America 87 (R+M)/2 or higher Fuel...
  • Page 111 SPECIFICATIONS MODEL SPYDER GS BRAKES Foot-actuated, fully integrated hydraulic Type 3-wheel braking system with ABS and EBD Dual discs (250 mm x 6 mm) Front brake (9.8 in x 0.24 in) with 4 piston calipers Single disc (250 mm x 6 mm) Rear brake (9.8 in x 0.24 in) with 1 piston caliper 545 to 570 mL...
  • Page 112 SPECIFICATIONS MODEL SPYDER GS DIMENSION Overall length 2 667 mm (105 in) Overall width 1 506 mm (59 in) Overall height 1 145 mm (45 in) Seat (top) height 737 mm (29 in) Wheel base 1 727 mm (68 in) Wheel track Front 1 308 mm (51.5 in)

  • Page 113: Warranty

    WARRANTY _____________________...

  • Page 114: Brp Limited Warranty - Usa And Canada: 2008 Can-Am™ Spyder

    2008 CAN-AM™ SPYDER™ ROADSTER 1. SCOPE OF THE LIMITED WARRANTY Bombardier Recreational Products Inc. (“BRP”)* warrants its 2008 Can-Am Spyder roadsters sold by authorized Spyder Dealers (as defined below) in the fifty United States and in Canada from defects in material or workmanship for the period and under the conditions described below.
  • Page 115 BRP LIMITED WARRANTY – USA AND CANADA: 2008 CAN-AM™ SPYDER™ ROADSTER – Damage caused by failure to provide proper maintenance or storage, as de- scribed in the Operator’s Guide. – Damage resulting from removal of parts, improper repairs, improper service or...
  • Page 116 BRP LIMITED WARRANTY – USA AND CANADA: 2008 CAN-AM™ SPYDER™ ROADSTER (d) for Spyder roadsters sold to residents of the United States, FIVE (5) YEARS or THIRTY THOUSAND (30 000) KILOMETERS (18,641 MILES), whichever occurs first, on the emission related components included in the chart below:...
  • Page 117 BRP LIMITED WARRANTY – USA AND CANADA: 2008 CAN-AM™ SPYDER™ ROADSTER 6. WHAT TO DO TO OBTAIN WARRANTY COVERAGE The customer must cease using the Spyder roadster upon the appearance of an anomaly. The customer must notify a servicing Spyder Dealer within two (2) days of the appearance of a defect, and provide it with reasonable access to the product and reasonable opportunity to repair it.

  • Page 118: Brp Limited Warranty Outside Usa And Canada: 2008 Can-Am Tm Spyder Tm Roadster

    1. SCOPE OF THE LIMITED WARRANTY Bombardier Recreational Products Inc. (“BRP”)* warrants its 2008 Can-Am Spyder roadsters (the "Products") sold by authorized Can-Am Spyder roadster distributors and dealers located in the EEA (the "EEA" or "European Economic Area" shall mean the countries member of the European Union plus Norway, Iceland and Liechtenstein) or elsewhere, except in the USA and Canada** (the "Distributors / Dealers") from defects in material or workmanship for the period...
  • Page 119 BRP LIMITED WARRANTY OUTSIDE USA AND CANADA: 2008 CAN-AM SPYDER ROADSTER 3. EXCLUSIONS – ARE NOT WARRANTED The following are not warranted under any circumstances: – Replacement of routine maintenance items such as, without limitation, oil and lubricants, filters and spark plugs.
  • Page 120 BRP LIMITED WARRANTY OUTSIDE USA AND CANADA: 2008 CAN-AM SPYDER ROADSTER 4. WARRANTY COVERAGE PERIOD This warranty will be in effect from the date of delivery to the first retail consumer or the date the Product is first put into use, whichever occurs first and for the fol-...
  • Page 121 BRP LIMITED WARRANTY OUTSIDE USA AND CANADA: 2008 CAN-AM SPYDER ROADSTER 6. WHAT TO DO TO OBTAIN WARRANTY COVERAGE The customer must cease using the Product upon the appearance of an anomaly. The customer must notify an authorized servicing Distributor / Dealer within two (2) months of the appearance of a defect, and provide it with reasonable access to the Product and reasonable opportunity to repair it.
  • Page 122 BRP LIMITED WARRANTY OUTSIDE USA AND CANADA: 2008 CAN-AM SPYDER ROADSTER 9. CONSUMER ASSISTANCE In the event of a controversy or a dispute in connection with this limited war- ranty, BRP suggests that you try to resolve the issue at the dealership level.

  • Page 123: California Emission Control Warranty Statement

    The California Air Resources Board and BRP US Inc. ("BRP")*, on behalf of Bombardier Recreational Products Inc., are pleased to explain the emission control system warranty on your 2008 Can-Am Spyder roadster. In California, new motor vehicles must be designated, built and equipped to meet the State’s stringent anti-smog standards.

  • Page 124: Privacy Obligation/Disclaimer

    PRIVACY OBLIGATION/DISCLAIMER We wish to inform you that your contact information will be used for safety and warranty purposes. Sometimes, we also use the contact information of our clients to inform them about our products and to present them offers. Should you prefer not to receive information on our product, services and offers, please let us know by writing to the address below.

  • Page 125: Change Of Address/Ownership

    STOLEN UNITS: If your personal vehicle is stolen, you should notify BRP or an au- thorized Can-Am roadster dealer. We will ask you to provide your name, address, phone number, the vehicle identification number and the date it was stolen.
  • Page 126 CHANGE OF ADDRESS/OWNERSHIP _____________________...
  • Page 127 WARNING The Spyder roadster is a different type of vehicle- it requires special skills and knowledge. Learn how the Spyder roadster is different. Read this operator’s guide and watch the safety video. Complete a training course (if available), practice, become proficient with the controls, and get a proper license.

Table of Contents