Related Manuals for SHOWTEC 30690
Summary of Contents for SHOWTEC 30690
- Page 1 MANUAL ENGLISH Studio Beam CDM/HCI-150 Ordercode: 30690 Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands...
-
Page 2: Table Of Contents
Available lenses ................................10 Changing the lens ..............................10 Removing the lens ..............................10 Maintenance ..................................11 Changing the lamp ..............................11 Replacing the Fuse ..............................11 Cleaning VNSP, NSP, MFL and WFL glass lenses....................11 Troubleshooting ................................12 No Light ..................................12 Product Specifications ..............................13 Dimensions ..................................14 Ordercode: 30690... -
Page 3: Warning
Save the carton and all packing materials. In the event that a fixture must be returned to the factory, it is important that the fixture be returned in the original factory box and packing. Your shipment includes: Showtec Studio Beam CDM/HCI-150 with power cable (1 m) • Filter frame •... - Page 4 • If your Showtec device fails to work properly, discontinue the use immediately. Pack the unit securely (preferably in the original packing material), and return it to your Showtec dealer for service.
-
Page 5: Operating Determinations
The installation must always be secured with a safety attachment, e.g. an appropriate safety net or safety cable. • When rigging, derigging or servicing the Studio Beam, always make sure, that the area below the installation site is secured and that there are not any unauthorized people around. Ordercode: 30690... - Page 6 UK Cable US Cable BROWN YELLOW/COPPER PHASE BLUE BLACK SILVER NEUTRAL YELLOW/GREEN GREEN GREEN PROTECTIVE GROUND Make sure that the device is always properly connected to the earth! Improper installation can cause serious injuries and/or damage of property! Ordercode: 30690...
-
Page 7: Return Procedure
After this period complaints will not be handled anymore. Complaints will only then be considered if the client has so far complied with all parts of the agreement, regardless of the agreement from which the obligation is resulting. Ordercode: 30690... -
Page 8: Description Of The Device
80965 – Powerstar HCI/CDM G12 Osram, 150W 80974 – Discharge Bulb Philips, G12 80975 – Discharge Bulb Philips, G12 Overview Fig. 01 01) Filter frame 02) Lens 03) Lens catcher 04) Filter frame retaining clip 05) Adjustment screw 06) Ballast case Ordercode: 30690... -
Page 9: Backside
Before plugging the unit in, always make sure that the power supply matches the product specification voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa. Connect the device to the main power supply. Ordercode: 30690... -
Page 10: Installing The Lamp
Studio Beam CDM/HCI-150 Installing the lamp The Showtec Studio Beam CDM/HCI-150 uses the Powerstar HCI/CDM G12 Osram, 150W (ordercode 80964 and 80965) and the Discharge Bulb Philips, G12 (ordercode 80974 and 80975. Use only the appropriate lamp for your unit. Note that product versions, that use other lamps, may be offered in the future. -
Page 11: Available Lenses
03) Tilt the front of the fixture down by at least 45°. 04) Press the spring clip to release the lens (fig. 07). 05) Allow the lens to slide forward and rest upon the lens catchers (fig. 08). 06) Carefully remove the lens. Ordercode: 30690... -
Page 12: Maintenance
Dampen a clean lint-free cloth with vinegar or household ammonia. You may also use water, but it will leave spots that can be removed by gently polishing the lens with a clean and dry cloth. Starting from the center, gently wipe the lens. Gently push the lens until it is positioned properly. Ordercode: 30690... -
Page 13: Troubleshooting
05) If you are unable to determine the cause of the problem, do not open the Studio Beam, as this may damage the unit and the warranty will become void. 06) Return the device to your Showtec dealer. Problem Probable cause(s) -
Page 14: Product Specifications
Studio Beam CDM/HCI-150 Product Specifications Model: Showtec Studio Beam CDM/HCI-150 Input Voltage: 240VAC, 50Hz Power consumption: 150W Fuse: T3,15AL/250V Dimensions: 285 x 270 x 380 mm (LxWxH) Weight: 6,6 kg Electro-mechanical effects: Light source: 1 x JCL-T 150W/942 discharge lamp (included) -
Page 15: Dimensions
Studio Beam CDM/HCI-150 Dimensions Ordercode: 30690... - Page 16 ©2016 Showtec...
Need help?
Do you have a question about the 30690 and is the answer not in the manual?
Questions and answers