Takenaka System FS5000GE Instruction Manual page 38

*1 A: Asynchronous shutter
M: Continuous shutter
*2 H: High speed shutter
L: Low speed shutter
*3 N: Normal scan
F: Partial scan
*4: Exposure time
The format of "Exposure time" complies with one of the followings:
a. 4 characters representing 2-byte number and corresponding to the hexadecimal system
b. 4 characters of "S" "0 to 9" ".." for externally specifying a shutter position (2 full stops of "." in the last are
mandatory.)
● In the case where the electronic shutter exposure time is externally set:
When the exposure time is set in the unit of H (horizontal scan time), the exposure setting count value of the time in H is
set.
Example) If the shutter exposure time is 17Hs (Horizontal scan time × 17):
STX: "S": ".": ".": ".": "0011": ETX
● In the case where the exposure time is set by the hypothetical shutter SW number:
Example) If the shutter SW is set to "4":
STX: "S": ".": ".": ".": "S4..": ETX
● In the case where the exposure time is set to 3Hs in the asynchronous/high speed shutter mode:
STX: "S": "A": "H": ".": "0003": ETX
● In the case where the control is returned to the setting by the (hypothetical) shutter switch:
STX: "S": ".": ".": ".": "0000": ETX
(Note) The exposure time setting using "S" command is given priority over the set position of the shutter switch.
It is needed to specify the exposure time to "0000" and transmit the S command via serial communication to
restore the exposure time setting to the value specified by the set position of the (hypothetical) shutter switch.
(Note) The set contents are stored by saving them to the program page by "W" command ("WA" to "WF").
(6) Command "A"
Function: Command for setting analog image signal
Transmission from host: STX: "A": (SETUP set value): (WC set value): ".": ETX
Return by camera:
(!) Nevertheless FS5000GE does not use the values in parentheses, it is not regarded as error even when the value in
parentheses is input. The received set value is neglected.
(7) Command "E"
Function: Command for editing shutter menu
Transmission from host: STX: "E": "H" or "L" : SW0: SW1: SW2: SW3: SW4: SW5: SW6: SW7: SW8: SW9: ETX
Return by camera:
The transmitting command has the following meaning.
STX: "E": "H" or "L" : SW0: ... : SW9: ETX
*1
*1 H: High speed shutter
L: Low speed shutter
*2 The exposure time (H) to be allocated to the shutter SW number is expressed in 4 digits in the hexadecimal system
for SW0 to SW9.
Example) If only the exposure time of SW5 for the high speed shutter operation is changed to 88 (decimal):
STX: "E": "H": ".": ".": ".": ".": "."
: "0058": ".": ".": ".": ".": ETX
(Note) For the SW0, regardless of the specified exposure time ,it always goes into no shutter operation mode by setting
the shutter switch position to 0.
(Note) The allowable range is as follows when in setting the exposure time by this command. The operation out of the
range is not guaranteed.
In High speed shutter: H'0000 to H'04E4 (D'0 to 1252) (Where, "0" is used only when cancelling the external shutter setting. )
In Low speed shutter: H'0000 to H'00FF (D'0 to 255) (Where, "0" is used only when cancelling the external shutter setting. )
(8) Command "W"
Function: Command for saving operation mode (Write into page memory)
Transmission from host: STX: "W": memory page ("A" to "F"): ETX
Return by camera:
The current setting can be written and saved in the EEPROM of the specified page number.
STX: ACK: ETX (transaction completion), or STX: NAK: ETX (transaction rejection)
STX: ACK: ETX (transaction completion), or STX: NAK: ETX (transaction rejection)
*2 ... *2
STX: ACK: ETX (transaction completion), or STX: NAK: ETX (transaction rejection)
- 38 -
M10510B;38/58