Table of Contents
Advertisement
<MENU2> Display content
PWC:
Whether the pulse width operation mode is ENABLED or
DISABLED in the asynchronous shutter mode when the
shutter switch is positioned at "9" , is selected.
DUMP:
Whether the Fast-dump operation for the (preset)
asynchronous shutter mode is used (ENABLED) or not used
(DISABLED) is selected.
<MENU3> Display content
BAUD:
The baud rate used for serial communication is displayed.
The baud rate is fixed to 9600bps for this camera. The setting can not be
changed.
H-RESET:
It is selected whether or not to permit to reset (initialize) H
timing. If it is permitted (ENABLED), H timing (horizontal
synchronization timing ) is reset by the trigger signal input in
asynchronous shutter operation.
STRB:
The output signal on STRB output terminal of camera connector
is selected.
OFF ... Always output H level (Default setting)
STRB ...Output STRB(strobe timing signal)
BUSY ...Output BUSY(Asynchronous shutter busy signal)
(Note) The strobe signal can be output in any setting of Asynchronous shutter /
Continuous shutter / No shutter.
<MENU4> Display content
PATTERN:
This is to switch between ON /OFF for the test pattern output.
bit:
This is to select the output bit format (gray scale) of the output
data in Camera Link STD. 10bit, 8bit or 12bit format are
settable for this camera. Default setting is 10bit gray scale.
VSUB:
The setting value of Vsub voltage (substrate voltage of CCD
element) is displayed.
Since the value is optimally set before shipment, the user is
not required to change it as a general rule.
*
The following items are for display only; they cannot be directly changed
on the menu. These are automatically updated when a corresponding
change is made by the serial communication command.
MS= The current position of the (hypothetical) mode switch is displayed.
SS= The current position of the (hypothetical) shutter setting switch (EXP.) is displayed.
MF= The information (16 bits x 2 sets) of the internal mode flags of the camera (internal flags
to determine operation) is displayed in the hexadecimal system. The details of the
internal flags are described later.
Tc=
The current internal temperature of the camera is displayed in Celsius. The temperature
data are refreshed every 0.4 seconds.
● Menu (MENU1) display when setting AGC(Auto Gain Control)
When AGC is set ON, the value which is displayed on the left side column of
"GAIN" on MENU1 is the current Preamplifier gain, the value on the right side
is set value of "AGC"(reference value).
In "GAIN" column, the current Preamplifier gain is displayed. e.g. "A 120"
"A" represents dynamically changing value of Preamplifier gain
When it reaches to upper limit or lower limit of variable range of Preamplifier, "
displayed. e.g. "
A255" (Limit value varies among camera models)
↑
↑
- 33 -
M10510B;33/58
* M E N U 2
M E N U
:
O N
-
:
( R e s e r v e d )
-
:
( R e s e r v e d )
P W C
:
D I S A B L E D
D U M P
:
D I S A B L E D
* M S = A
S S = 7
M F = 0 0 0 0 . 0 0 0 0
F S 5 0 0 0 G E
Menu 2 display
* M E N U 3
M E N U
: O N
-
: ( R e s e r v e d )
B A U D
: 9 6 0 0 b p s
-
: ( R e s e r v e d )
H - R E S E T : D I S A B L E D
-
: ( R e s e r v e d )
S T R B
: O F F
* M S = C
S S = 7
M F = 0 0 0 0 . 0 0 0 0
F S 5 0 0 0 G E
Menu3 display
* M E N U 4
M E N U
: O N
P A T T E R N : O F F
b i t
: 1 0 b i t
-
: ( R e s e r v e d )
-
: ( R e s e r v e d )
-
: ( R e s e r v e d )
V S U B
:
7 9 = H ' 4 F
* M S = C
S S = 7
M F = 0 0 0 0 . 0 0 0 0
F S 5 0 0 0 G E
Menu4 display
* M E N U １
M E N U
:
O N
G A I N
: A 7 5
/
7 0 A E C
O F F S E T :
1 4 0
S . T I M E :
4 8 4 h
(
1 4 . 3 1 ) m s
S . F O R M : N O R M A L
／
AGC operating
Menu1display
"(upper limit) or "
"(lower limit) marks are
↓
[ V . X . X X ]
[ V . X . X X ]
[ V . X . X X ]
Advertisement
Table of Contents
