Emerson unidrive sp User Manual page 158

Safety Mechanical
Product
Information information Installation
Parameter
6.01 Stop mode
6.03 Line power supply loss mode
6.04 Start / stop logic select
6.06 Injection braking level
6.07 Injection braking time
6.08 Hold zero speed
6.09 Catch a spinning motor
6.12 Enable stop key
6.13 Enable forward / reverse key {0.28}
6.15 Drive enable
6.16 Electricity cost per kWh
6.17 Reset energy meter
6.18 Time between filter changes
Filter change required /
6.19
change done
6.20 Powered-up time: years.days
Powered-up time:
6.21
hours.minutes
6.22 Run time: years.days
6.23 Run time: hours.minutes
6.24 Energy meter: MWh
6.25 Energy meter: kWh
6.26 Running cost
6.27 Time before filter change due
Select clock for trip log time
6.28
sampling
6.29 Hardware enable
6.30 Sequencing bit: Run forward
6.31 Sequencing bit: Jog forward
6.32 Sequencing bit: Run reverse
Sequencing bit: Forward /
6.33
reverse
6.34 Sequencing bit: Run
6.35 Forward limit switch
6.36 Reverse limit switch
6.37 Sequencing bit: Jog reverse
6.39 Sequencing bit: Not stop
6.40 Enable sequencer latching
6.41 Drive event flags
6.42 Control word
6.43 Control word enable
6.44 Active supply
Force cooling fan to run at full
6.45
*****
speed
6.46 Nominal low voltage supply
Disable line power supply /
6.47 phase loss detection from
input rectifier
Line powersupply loss ride
6.48
through detection level
Disable multi-module drive
6.49
module number storing on trip
6.50 Drive comms state
6.51 External rectifier not active
RW Read / Write RO Read only
FI Filtered DE Destination
*For more information, refer to section 11.21.5 Stop modes on page 227.
**For more information, refer to section 11.21.6 Line power supply loss
modes on page 228.
***For more information, refer to section 11.21.7 Start / stop logic
modes on page 230.
****For more information, refer to section 11.21.8 Catch a spinning
motor on page 231.
158
Electrical Getting Basic Running the
Installation Started parameters
Range( )
OL
COASt (0), rP (1),
rP.dcl (2), dcl (3),
td.dcl (4), diSAbLE (5)
diS (0), StoP (1), ridE.th (2)
0 to 4
0 to 150.0%
0.0 to 25.0s
OFF (0) or On (1)
{0.33} 0 to 3
OFF (0) or On (1)
OFF (0) or On (1)
OFF (0) or On (1)
0.0 to 600.0 currency units per kWh
OFF (0) or On (1)
0 to 30,000 hrs
OFF (0) or On (1)
0 to 9.364 years.days
0 to 23.59 hours.minutes
0 to 9.364 years.days
0 to 23.59 hours.minutes
±999.9 MWh
±99.99 kWh
±32,000
0 to 30,000 hrs
OFF (0) or On (1)
OFF (0) or On (1)
OFF (0) or On (1)
OFF (0) or On (1)
OFF (0) or On (1)
OFF (0) or On (1)
OFF (0) or On (1)
OFF (0) or On (1)
OFF (0) or On (1)
OFF (0) or On (1)
OFF (0) or On (1)
OFF (0) or On (1)
0 to 65,535
0 to 32,767
OFF (0) or On (1)
OFF (0) or On (1)
OFF (0) or On (1)
48V to 96V
OFF (0) or On (1)
0 to DC_VOLTAGE_SET_MAX V
OFF (0) or On (1)
drv (0), SLot 1(1), SLot 2 (2), SLot 3 (3)
OFF (0) or On (1)
Uni Unipolar Bi
NC Not copied RA
www.controltechniques.com
SMARTCARD
Optimization
motor operation
CL OL
COASt (0), rP (1),
rP (1)
no.rP (2)
100.0%
1.0
OFF (0)
0 to 1 0
200V drive: 205, 400V drive: 410,
575V drive: 540, 690V drive: 540
Bi-polar Bit Bit parameter
Rating dependent PT Protected
*****The drive thermal model system normally controls the fan speed,
however the fan can be forced to operate at full speed if this parameter
is set to 1. When this is set to 1 the fan remains at full speed until 10s
after this parameter is set to zero. Note that the fan willl only run at full
speed if the drive is not in a UU condition.
Technical
Onboard Advanced
Diagnostics
PLC parameters Data
Default( )
VT SV
no.rP (2)
RW Txt
diS (0) RW Txt
4 RW Uni
RW Uni
RW Uni
On (1) RW Bit
1 RW Uni
OFF (0) RW Bit
OFF (0) RW Bit
On (1) RW Bit
0 RW Uni
OFF (0) RW Bit
0 RW Uni
OFF (0) RW Bit
RW Uni
RW Uni
RO Uni
RO Uni
RO
RO
RO
RO Uni
OFF (0) RW Bit
RO Bit
OFF (0) RW Bit
OFF (0) RW Bit
OFF (0) RW Bit
OFF (0) RW Bit
OFF (0) RW Bit
OFF (0) RW Bit
OFF (0) RW Bit
OFF (0) RW Bit
OFF (0) RW Bit
OFF (0) RW Bit
0 RW Uni
0 RW Uni
OFF (0) RW Bit
RO Bit
OFF (0) RW Bit
48 RW Uni
OFF (0) RW Bit
RW Uni
OFF (0) RW Bit
RO Txt
OFF (0) RW Bit
Txt Text string
US User save PS
Unidrive SP Free Standing User Guide
UL Listing
Information
Type
US
US
US
RA US
US
US
US
US
US
US
US
NC
US
PT
NC PT
NC PT
NC PT PS
NC PT PS
Bi NC PT PS
Bi NC PT PS
Bi NC PT
NC PT PS
US
NC PT
NC
NC
NC
NC
NC
NC
NC
NC
NC
US
NC
NC
US
NC PT
US
PT US
US
RA US
US
NC PT
Power down save
Issue Number: 1