Additional Information For Controller Setting - Konica Minolta bizhub Pro 951 Additional Information

7
7.1.2

Additional Information for Controller Setting

The following contents have been added to [08 Administrator Setting] - [01 Software Switch Setting].
Refer also to "6.2.2 [08 Administrator Setting] - [01 Software Switch Setting]" in [User's Guide - POD Admin-
istrator's Reference] of this machine (or "11.2.2 [08 Administrator Setting] - [01 Software Switch Setting]" in
[User's Guide - Main Body] for bizhub PRESS 1250P (Inch area)).
Specify settings by selecting OFF(0)/ON(1) for each switch. See the following table for selecting OFF(0)/ON(1)
for a desired switch. All the default settings are OFF(0).
Switch
No.
46
48
49
53
54
55
7-4
Description
Since printing misalignment occurs when the
minimum value of the PDF trimmed size (Crop-
Box) is not 0, set the trimmed size area to be lo-
cated in the center of the page.
When using PageScope Direct Print, a PDF job of
a paper size larger than the maximum size speci-
fied for this machine should be output without
causing a PS error.
When standard and custom sizes are mixed in
originals and left binding is selected in duplex
printing, the top binding layout is inevitably se-
lected for custom size originals to meet specifica-
tions; therefore, use this setting to apply the left
binding layout also to the custom size originals.
Although the machine performs transmission pro-
cessing for each status (more than once) when
"@PJL INFO STATUS" command is received and
transmitted, statuses should be merged to per-
form a single transmission processing.
Change the order of notice JobStart/End by
"@PJL USTATUS JOB=ON" command from Job-
Start1 -> JobStart2 -> ... JobEnd1 -> JobEnd2...
to JobStart1 -> JobEnd1 -> JobStart2 ->
JobEnd2..., so that the timing of notice JobStart
should be after the first sheet is output.
If "@PJL EOJ NAME" is included in a file, job sep-
aration occurs to possibly result in returning un-
expected number of pages. To solve this
problem, add a process to distinguish the job
names of "@PJL JOB NAME" and "@PJL EOJ
NAME" so that it should be treated as a single job
only when the job names are identical.
Other Additional Information and Corrections
Setting
Setting value:
0: Do not locate in the center of the
page
1: Locate in the center of the page
Setting value:
0: Cannot be output due to a PS error
1: Can be output without causing a PS
error
To output with this setting, the follow-
ing conditions should be satisfied:
• Set Switches No. 32 and No. 42 to
"1."
Available paper size is 62.99" e
•
82.68" (1600 e 2100 mm) at maxi-
mum.
• Only the maximum printing area is
printable.
Important:
When a change is made for the soft-
ware switch settings, turn the sub pow-
er off and back on again for the change
to take effect.
Setting value:
0: Top binding layout
1: Left binding layout
[Restrictions]
Available only for PostScript files.
Setting value:
0: Perform transmission processing for
each status
1: Merge statuses to perform a single
transmission processing
Setting value:
0: The JobStart notice is given after all
jobs are received
1: The JobStart notice is given after the
first sheet is output
Setting value:
0: Do not distinguish the job names of
"@PJL JOB NAME" and "@PJL EOJ
NAME"
1: Distinguish the job names of "@PJL
JOB NAME" and "@PJL EOJ NAME"
Important:
The Software Switch No. 7 should be
"0" to distinguish the job names.
bizhub PRESS 1250/1250P/1052, bizhub PRO 951
7.1