Esu LokSound micro V4.0 Instruction Manual page 3

Contents
8.2.1. Programming with DCC Systems .............................28
8.2.2. Programming with the ESU ECoS .............................29
8.2.3. Programming with Märklin® 6021 ..........................29
8.2.3.1. Changing the Programming Mode ........................29
8.2.3.2. Short Mode ..........................................................29
8.2.3.3. Long mode ...........................................................29
8.2.4. Programming with the Märklin® Mobile Station® ...30
8.2.5. Programming with the Märklin® Central Station .....31
8.2.6. Programming with the ESU LokProgrammer ............31
8.2.7. Programming with the ROCO® Multimaus ..............31
8.2.8. Programming with the ROCO® LokMaus II ..............32
9. Address Settings .................................................... 33
9.1. Short Addresses in DCC Mode ....................................33
9.2. Long Addresses in DCC Mode ....................................33
9.3. Motorola® Address ....................................................33
10. Adapting the Driving Characteristics ................. 34
10.1. Acceleration and Deceleration ..................................34
10.1.1. Switching Acceleration / Deceleration ....................34
10.1.2. Shunting Mode ......................................................34
10.2. Starting Voltage, Maximum and Medium Speed .......34
10.3. Speed Curve .............................................................35
10.4. Changing between Operating Modes .......................35
10.4.1. Changing from Digital to Analogue DC .................35
10.4.2. Changing from Digital to Analogue AC .................35
10.4.3. Changing from Analogue to Digital (directional bit) 35
10.4.4. Changing from Digital to Digital ............................36
10.4.5. Changing modes with Analogue Mode turned off .36
10.5. Brake Sectors ............................................................36
10.5.1. DC Brake Mode .....................................................36
10.5.2. Märklin® Brake Mode ...........................................36
10.5.3. Selectrix® Diode Brake Sector ................................37
10.5.4. Lenz® ABC Brake Mode ........................................37
10.6. Constant Brake Distance ...........................................37
10.6.1. Linear Brake Distance .............................................38
10.6.2. Constant Linear Brake Distance ..............................38
10.7. Settings for Analogue Operation ...............................38
10.7.1. DC Analogue Operation ........................................38
10.7.2. AC Analogue Operation ........................................38
11. Motor Control ...................................................... 39
11.1. Adjusting Load Compensation ..................................39
11.1.1. Parameter for frequently used motors ....................39
11.1.2. Adjustments for other Motors / „Fine Tuning" .......39
11.1.2.1. Parameter „K" ....................................................39
11.1.2.2. Parameter „I" .....................................................39
11.1.2.3. Reference Voltage ...............................................40
11.1.2.4. Parameter "K slow" ............................................40
11.1.2.5 Adaptive Regulation Frequency ............................40
11.2. Turning off Load Compensation ................................41
11.3. Adapting Load Control Frequency .............................41
11.4. Dynamic Drive Control: Up and Down the Hill...........41
11.5. Settings for the C-Sinus Motor ..................................41
12. Function outputs .................................................. 42
12.1. Physical function outputs ..........................................42
12.2. Allocation of Function Buttons (Function Mapping) ...42
12.2.1. Index CV access .....................................................42
12.2.2. Function Mapping - Chart ......................................43
12.2.3. Allocation of function keys with LokProgrammer ...43
12.3. Special Effects on function outputs ...........................44
12.3.1. Switching on outputs and different options ...........44
12.3.2. Adjusting the Lighting Effects ................................44
12.3.3. Grade Crossing holding time..................................48
12.3.4. Flash Rate ..............................................................48
12.3.5. Automatic switch-off .............................................48
12.3.6. Digital Couplers .....................................................48
12.3.6.1. Operation mode „Coupler" ................................48
12.3.6.2. Automatic „Coupler" Function (Removing/Pushing) 49
12.4. Analogue Settings.....................................................49
12.5. LGB® Pulse Sequence Mode .....................................49
12.6. Swiss Headlight Mode...............................................49
13. Adjusting the sound effects ................................ 50
13.1. Adjusting the sound volume .....................................50
13.1.1. Adusting the master volume ..................................50
13.1.2. Single sounds tables...............................................50
3