Related Manuals for Esu LokPilot V2.0
Summary of Contents for Esu LokPilot V2.0
-
Page 1: User Manual
LokPilot V2.0 Art-No. 52600 / 52602 LokPilotDCC V2.0 Art-No. 52601/ 52603 Version 1.1, 1st edition January 2005 user manual LokPilot V2.0 / LokPilot DCC V2.0 01/2005... - Page 2 • Improved function mapping: All outputs can be General Features: assigned to any function button LokPilot V2.0 is the successor of the popular LokPilot • Lighting effects: Strobe, Double Strobe, Mars- und decoder. It enhances the already outstanding Gyro light, Firebox, Blinker, Flash.
- Page 3 Fig. 2 - Wiring of LokPilot with isolated funktions green violet yellow withe light light back front LokPilot chassis orange grey balck engine Fig. 3 - Wiring of LokPilot with the common pole connected to the chassis user manual LokPilot V2.0 / LokPilot DCC V2.0 01/2005...
- Page 4 Incandescent lamps have a high starting current contacts. and this may activate the overload protection of How to proceed depends on how the headlights and the decoder when the lights are switched on. other functions are wired: user manual LokPilot V2.0 / LokPilot DCC V2.0 01/2005...
- Page 5 Motorola-mode (not for LokPilotDCC V2.0) 11) for locomotives whose light and function outputs The LokPilot V2.0 can be used with all Märklin® devices are connected as shown in figure 2. All other smoke or compatible systems previously sold or currently on generators may draw too much current.
- Page 6 Adjusting Load control Adjusting Load control buttons. The load control of the LokPilot V2.0 can be adapted • Each physical output must be assigned to a function to different types of motors. The standard settings button and also has to be „switched on“ initially.
- Page 7 • Example 2 Example 2 Example 2: The LokPilot V2.0 offers the feature to adjust the brightness of lamps in 15 steps in order to adapt the Blinking light on AUX2 and F6. light intensity optimally to the specific model. The A blinking light should be wired to AUX 2 and assigned lamps are supplied with pulses, i.e.
- Page 8 When using LGB-command stations or the Roco Lok- own fax-no.) and we will reply within a few days. maus I the LokPilot V2.0 can be set to pulse control. Set bit 5 in CV 49 for this purpose. Subsequently the...
- Page 9 Fig. 4 Function Mapping user manual LokPilot V2.0 / LokPilot DCC V2.0 01/2005...
- Page 10 CV 17 contains the higher value Byte (Bit 6 and 9999 Bit 7 must always be active), CV 18 contains the Lower value Byte. Only active, if feature is switched on in CV 29 (see below) user manual LokPilot V2.0 / LokPilot DCC V2.0 01/2005...
- Page 11 CV 2, 5, 6 speed curve through CV 67 - 96 5 Selection of address (DCC-mode only) short addresses (CV 1) in DCC-mode Long addresses (CV 17+18) in DCC-mode user manual LokPilot V2.0 / LokPilot DCC V2.0 01/2005...
- Page 12 Märklin Brake mode on 1 ZIMO Brake mode ZIMO Brake mode off ZIMO Brake mode on 2 not used 3 Lenz DCC Brake mode Lenz Brake mode off Lenz Brake mode on user manual LokPilot V2.0 / LokPilot DCC V2.0 01/2005...
- Page 13 Vol + 96 Headlights (high beam / low beam Vol + 112 Mars light Vol + 128 Gyro light Vol + 144 Vol = brightness. Range 0 (dark) - 15 (maximum) user manual LokPilot V2.0 / LokPilot DCC V2.0 01/2005...
- Page 14 Vol + 96 Headlights (high beam / low beam Vol + 112 Mars light Vol + 128 Gyro light Vol + 144 Vol = brightness. Range 0 (dark) - 15 (maximum) user manual LokPilot V2.0 / LokPilot DCC V2.0 01/2005...
- Page 15 0 – 255 function buttons to be active in status standstill - forward Standstill – forward B Bit Description Value 0 Acceleration on / off 1 Shunting speed on / off user manual LokPilot V2.0 / LokPilot DCC V2.0 01/2005...
- Page 16 Assignment of function outputs 0 - 255 function buttons to be active in back up mode Back up B Bit Description Value 0 Acceleration on / off 1 Shunting speed on / off user manual LokPilot V2.0 / LokPilot DCC V2.0 01/2005...
- Page 17 Assignment of function outputs 0 - 255 function button F1 to F1 to be active in forward mode Forward B Bit Description Value 0 Acceleration on / off 1 Shunting speed on / off user manual LokPilot V2.0 / LokPilot DCC V2.0 01/2005...
- Page 18 CV 150 163Assignment of Assignment of function outputs 0 - 255 function button F3 to F3 to be active in back up mode Back up B Description Value refer to CV 151 user manual LokPilot V2.0 / LokPilot DCC V2.0 01/2005...
- Page 19 CV 151 177Assignment of Assignment of function outputs 0 - 255 function button F6 to F6 to be active in forward mode Forward A Description Value refer to CV 147 user manual LokPilot V2.0 / LokPilot DCC V2.0 01/2005...
- Page 20 Description Value refer to CV 147 190Assignment of Assignment of function outputs function button F8 to F8 to be active in forward mode Forward B Description Value refer to CV 148 user manual LokPilot V2.0 / LokPilot DCC V2.0 01/2005...
- Page 21 CV 150 205Assignment of Assignment of function outputs function button F10 to F10 to be active in back up mode Back up B Description Value refer to CV 151 user manual LokPilot V2.0 / LokPilot DCC V2.0 01/2005...
- Page 22 CV 150 217Assignment of Assignment of function outputs function button F12 to F12 to be active in back up mode Back up B Description Value refer to CV 151 user manual LokPilot V2.0 / LokPilot DCC V2.0 01/2005...
- Page 23 Copyright 1998 - 2005 by ESU electronic solutions ulm GmbH & Co KG. Electrical characteristics and dimensions are subject to change without prior notice. All rights reserved. ESU may not be held responsible for any damage or consequential loss or damage caused by inappropriate use of the product, abnormal operating conditions, unauthorized modifications to the product, etc.
- Page 24 LokPilot V2.0 / LokPilot DCC V2.0 01/2005...