Table of Contents
Advertisement
8
RESETTING THE BOILER:
(Electronic Controls Boiler)
(45/3E, 57/3E, 45/4E & 57/4E)
If the boiler lockout light is illuminated
it is necessary to reset the appliance.
To do this turn the boiler thermostat
control knob fully anti-clockwise to
the OFF position and wait 10
seconds. Turn the control knob to the
required setting. The boiler will
commence sparking providing the
water temperature is sufficiently cool.
(51/5)
If the indicator light is illuminated
red/or flashing red, it is necessary to
reset the appliance. To do this turn
the boiler thermostat control knob
fully anticlockwise to the OFF position
and wait until the light shows orange.
Turn the control knob clockwise to
the required setting. The boiler will
commence the ignition sequence.
9
TO LIGHT THE FIRE: Push in
and turn the fire control knob anti-
clockwise to the positive stop at
position "
". Just before position
"
" is reached, a click will be heard
and the pilot should light, hold in the
control knob for approx 15 seconds,
release and turn to desired position.
The pilot can be seen through the
lower right hand gap between the
coals and front panel. If the burner
fails to light, turn the control knob to
the OFF position ( ) and repeat until
the burner lights. Continue to hold in
the control knob for a further 15
seconds. Release slowly and the
burner should stay alight.
CAUTION -
If the burner does not light
or stay alight, or if the flame goes out for
any reason, turn the control knob to the
OFF position (
) and wait for 3 minutes
before attempting to light the burner.
NOTE:
An electrical supply is not
needed to ignite the fire.
CONTROL KNOB POSITIONS: The
control knob has six positions giving
a choice of 5 settings, i.e.
Position
- OFF
Position
- IGNITION/PILOT
Position
1 - LOW
Position
2 - MED
Position
3 - MED/HIGH
Position
4 - HIGH
To adjust the fire to the required
setting, push in the control knob and
turn in the appropriate direction.
10
TO TURN THE FIRE OFF:
Push in the control knob and
turn clockwise to the OFF position.
The pilot light can be left on by
stopping at the
position but the fire
is not fully off until the knob is turned
to position
.
Controls Cover Panel
Fire Control
Bermuda SL3
Position
Indicator
Button
LIGHT EFFECT
The light effect is operated by a
switch below the control knob (O
denotes OFF and
and may be used either with or
without the fire being on.
Light Switch
page 5
TO SHUT DOWN THE BOILER
Turn the fire control knob to the OFF
position ( ), switch the bulbs OFF
and allow the fire to cool.
Remove the controls cover panel at
the bottom of the fire below the
coalbed by grasping it firmly by its
side edges and pulling forwards.
To switch the boiler off for short
periods. (Manual Controls Boiler)
Turn the boiler thermostat knob to the
OFF position (
Knob
remain alight.
To switch the boiler off for long
periods. (Manual Controls Boiler)
Turn the grey push button clockwise
and release. Turn the boiler
thermostat knob to the OFF position
(
).
To switch the boiler off. (Electronic
Controls Boiler) Turn the thermostat
knob to the OFF position (
If you are shutting down both the fire
and boiler, isolate the electrical
supply that serves the system
controls i.e. Timer/Programmer.
Replace the controls cover panel.
NOTE:
periods during cold weather, it is
denotes ON)
recommended that the whole system is
drained to avoid frost damage. Advice on
draining the system can be obtained from
your Service Engineer.
The glass front panel on this
appliance conforms to the required
safety standards. It does not give full
protection to the young or infirm: in
such cases we recommend a nursery
type guard which conforms to BS
6539. The panel becomes very hot
when the appliance is in use and
must not be touched.
THE APPLIANCE MUST NEVER BE
USED WITHOUT THE GLASS
FRONT PANEL FITTED.
). The pilot will
).
If the boiler is left off for long
GUARDING
Advertisement
Table of Contents
