Horizontal Right With Vertical Vent - Rheem 96v series Installation Instructions Manual

HORIZONTAL RIGHT / VERTICAL VENT HORIZONTAL RIGHT / VERTICAL VENT HORIZONTAL RIGHT / VERTICAL VENT HORIZONTAL RIGHT / VERTICAL VENT
AIRFL OW
PARTS NEEDED: PARTS NEEDED:
FROM PARTS BAG
(PROVIDED WITH UNIT)
COUPLING
FROM CONVERSION KIT RXGY-CK FROM CONVERSION KIT RXGY-CK
1/2" DRAIN
1/2" DRAIN
HOSE E
HOSE F
TOOLS/MATERIALS NEEDED: TOOLS/MATERIALS NEEDED: TOOLS/MATERIALS NEEDED:
ELECTRIC DRILL PLIERS PLIERS
1/8" DRILL BIT FLAT HEAD SCREWDRIVER FLAT HEAD SCREWDRIVER
NOTE: THESE CONVERSION INSTRUCTIONS ARE INTENTIONALLY GENERIC, SOME PARTS MAY BE DIFFERENT IN YOUR FURNACE NOTE: THESE CONVERSION INSTRUCTIONS ARE INTENTIONALLY GENERIC, SOME PARTS MAY BE DIFFERENT IN YOUR FURNACE NOTE: THESE CONVERSION INSTRUCTIONS ARE INTENTIONALLY GENERIC, SOME PARTS MAY BE DIFFERENT IN YOUR FURNACE NOTE: THESE CONVERSION INSTRUCTIONS ARE INTENTIONALLY GENERIC, SOME PARTS MAY BE DIFFERENT IN YOUR FURNACE NOTE: THESE CONVERSION INSTRUCTIONS ARE INTENTIONALLY GENERIC, SOME PARTS MAY BE DIFFERENT IN YOUR FURNACE NOTE: THESE CONVERSION INSTRUCTIONS ARE INTENTIONALLY GENERIC, SOME PARTS MAY BE DIFFERENT IN YOUR FURNACE NOTE: THESE CONVERSION INSTRUCTIONS ARE INTENTIONALLY GENERIC, SOME PARTS MAY BE DIFFERENT IN YOUR FURNACE NOTE: THESE CONVERSION INSTRUCTIONS ARE INTENTIONALLY GENERIC, SOME PARTS MAY BE DIFFERENT IN YOUR FURNACE NOTE: THESE CONVERSION INSTRUCTIONS ARE INTENTIONALLY GENERIC, SOME PARTS MAY BE DIFFERENT IN YOUR FURNACE NOTE: THESE CONVERSION INSTRUCTIONS ARE INTENTIONALLY GENERIC, SOME PARTS MAY BE DIFFERENT IN YOUR FURNACE
NOTE: STEPS 1- 5 SHOWN WITH FURNACE IN "AS SHIPPED CONDITION" NOTE: STEPS 1- 5 SHOWN WITH FURNACE IN "AS SHIPPED CONDITION" NOTE: STEPS 1- 5 SHOWN WITH FURNACE IN "AS SHIPPED CONDITION"
1
1a - REMOVE FLUE TRANSITION, TRANSITION COUPLING, AND ELBOW. 1a - REMOVE FLUE TRANSITION, TRANSITION COUPLING, AND ELBOW. 1a - REMOVE FLUE TRANSITION, TRANSITION COUPLING, AND ELBOW.
(NOTE: REMOVE INDUCER COUPLING W/ ELBOW FOR EASIER (NOTE: REMOVE INDUCER COUPLING W/ ELBOW FOR EASIER (NOTE: REMOVE INDUCER COUPLING W/ ELBOW FOR EASIER
REMOVAL).
1b - REMOVE CONDENSATE TRAP AND HOSES. 1b - REMOVE CONDENSATE TRAP AND HOSES.
(NOTE: TO REMOVE TRAP REMOVE (2) SCREWS AND PULL (NOTE: TO REMOVE TRAP REMOVE (2) SCREWS AND PULL (NOTE: TO REMOVE TRAP REMOVE (2) SCREWS AND PULL
STRAIGHT OUT).
1a
1b
INTAKE
INTAKE AIR
DIFFUSER
AND NUT
CONDENSATE CONDENSATE
TRAP GASKET TRAP GASKET
5/16 HEX HEAD DRIVER 5/16 HEX HEAD DRIVER
1/4" HEX HEAD DRIVER 1/4" HEX HEAD DRIVER
FLUE TRANSITION (DISCARD) FLUE TRANSITION (DISCARD)
TRANSITION
COUPLING
(RETAIN)
ELBOW (DISCARD)
IDB COUPLING
(RETAIN)
VENT HOSE
(DISCARD)
HOSE "D"
(DISCARD)
PARTS NEEDED FOR THIS CONVERSION REQUIRE ITEMS PARTS NEEDED FOR THIS CONVERSION REQUIRE ITEMS PARTS NEEDED FOR THIS CONVERSION REQUIRE ITEMS
!
FROM THE PARTS BAG FROM THE PARTS BAG PARTS BAG AND CONVERSION KIT RXGY-CK PARTS BAG AND CONVERSION KIT RXGY-CK
YOU MUST HAVE THE PARTS OUTLINED BELOW BEFORE YOU MUST HAVE THE PARTS OUTLINED BELOW BEFORE YOU MUST HAVE THE PARTS OUTLINED BELOW BEFORE
PROCEEDING.
(X3)
#8 X 1/2"
1/4" BLACK 1/4" BLACK
2" PIPE GROMMET 2" PIPE GROMMET
SCREW VENT TUBE VENT TUBE
TUBING CUTTER TUBING CUTTER
2
2a - RELOCATE 1/2" VINYL CAP (YELLOW) ON THE INDUCER COUPLING. 2a - RELOCATE 1/2" VINYL CAP (YELLOW) ON THE INDUCER COUPLING. 2a - RELOCATE 1/2" VINYL CAP (YELLOW) ON THE INDUCER COUPLING.
2b - REMOVE 3-3/8" FLUSH MOUNT PLUG FROM JACKET SIDE-DISCARD. 2b - REMOVE 3-3/8" FLUSH MOUNT PLUG FROM JACKET SIDE-DISCARD. 2b - REMOVE 3-3/8" FLUSH MOUNT PLUG FROM JACKET SIDE-DISCARD.
2d - INSTALL 2-5/8" FLUSH MOUNT PLUG IN TOP PLATE. 2d - INSTALL 2-5/8" FLUSH MOUNT PLUG IN TOP PLATE. 2d - INSTALL 2-5/8" FLUSH MOUNT PLUG IN TOP PLATE.
2d INSTALL
2-5/8"
DISCARD DISCARD
2b 2b
NOTE:
IF THE IDB COUPLING IS REMOVED, IT MUST BE REPLACED IN THE IF THE IDB COUPLING IS REMOVED, IT MUST BE REPLACED IN THE IF THE IDB COUPLING IS REMOVED, IT MUST BE REPLACED IN THE
PROPER ORIENTATION. AN ARROW IS PRESENT ON THE COUPLING PROPER ORIENTATION. AN ARROW IS PRESENT ON THE COUPLING PROPER ORIENTATION. AN ARROW IS PRESENT ON THE COUPLING
TO INDICATE THE DIRECTION OF EXHAUST FLOW. MAKE SURE THE TO INDICATE THE DIRECTION OF EXHAUST FLOW. MAKE SURE THE TO INDICATE THE DIRECTION OF EXHAUST FLOW. MAKE SURE THE
ARROW POINTS IN THE CORRECT DIRECTION. ARROW POINTS IN THE CORRECT DIRECTION. ARROW POINTS IN THE CORRECT DIRECTION.
RXGY-CK RXGY-CK
2-5/8"
2-5/8" FLUSH
MOUNT PLUG
( 3.375)
MOVE
2a
RE-LOCATE RE-LOCATE
2c
ST-A1194-33-01
31