Rheem 96v series Installation Instructions Manual page 36

6
DIFFUSER
FULLY SEATED FULLY SEATED
7
PVC GLUE JOINT PVC GLUE JOINT
7a - INSTALL INTAKE PIPE: 7a - INSTALL INTAKE PIPE: INSTALL INTAKE PIPE: SLIDE INTAKE PIPE THROUGH THE LEFT SIDE KNOCKOUT, CLEAN AND PVC GLUE TO INTAKE COUPLING AS SHOWN. INSTALL INTAKE PIPE: SLIDE INTAKE PIPE THROUG SLIDE INTAKE PIPE THROUGH THE LEFT SIDE KNOCKOUT, CLEAN AND PVC GLUE TO INTAKE COUPLING AS SHOWN. SLIDE INTAKE PIPE THROUGH THE LEFT SIDE KNOCKOUT, CLEAN AND PVC GLUE TO INTAKE COUPLING AS SHOWN. SLIDE INTAKE PIPE THROUGH THE LEFT SIDE KNOCKOUT, CLEAN AND PVC GLUE TO INTAKE COUPLING AS SHOWN. SLIDE INTAKE PIPE THROUGH THE LEFT SIDE KNOCKOUT, CLEAN AND PVC GLUE TO INTAKE COUPLING AS SHOWN. SLIDE INTAKE PIPE THROUGH THE LEFT SIDE KNOCKOUT, CLEAN AND PVC GLUE TO INTAKE COUPLING AS SHOWN. SLIDE INTAKE PIPE THROUGH THE LEFT SIDE KNOCKOUT, CLEAN AND PVC GLUE TO INTAKE COUPLING AS SHOWN.
7b - INSTALL FLUE PIPE ASSEMBLY: INSTALL FLUE PIPE ASSEMBLY: INSERT FLUE PIPE
SLIDE ANGLED END THROUGH OPENING IN BLOWER SHELF AND ALIGN WITH ELBOW COUPLING. SECURE PIPE ASSEMBLY TO BLOWER SLIDE ANGLED END THROUGH OPENING IN BLOWER SHELF AND ALIGN WITH ELBOW COUPLING. SECURE PIPE ASSEMBLY TO BLOWER SLIDE ANGLED END THROUGH OPENING IN BLOWER SHELF AND ALIGN WITH ELBOW COUPLING. SECURE PIPE ASSEMBLY TO BLOWER SLIDE ANGLED END THROUGH OPENING IN BLOWER SHELF AND ALIGN WITH ELBOW COUPLING. SECURE PIPE ASSEMBLY TO BLOWER SLIDE ANGLED END THROUGH OPENING IN BLOWER SHELF AND ALIGN WITH ELBOW COUPLING. SECURE PIPE ASSEMBLY TO BLOWER
SHELF WITH (2) SCREWS AS SHOWN. ENSURE O-RING IS PROPERLY SEATED. SHELF WITH (2) SCREWS AS SHOWN. ENSURE O-RING IS PROPERLY SEATED. SHELF WITH (2) SCREWS AS SHOWN. ENSURE O-RING IS PROPERLY SEATED.
7c - SLIDE PIPE COLLAR ASSEMBLIES OVER THE (2) PIPES AND DRILL (8) 7c - SLIDE PIPE COLLAR ASSEMBLIES OVER THE (2) PIPES AND DRILL (8) 7c - SLIDE PIPE COLLAR ASSEMBLIES OVER THE (2) PIPES AND DRILL (8) Ø1/8" HOLES USING THE COLLARS AS A TEMPLATE.
SECURE WITH (8) SCREWS AS SHOWN. SECURE WITH (8) SCREWS AS SHOWN.
36
7a
INSERT FLUE PIPE ASSEMBLY THROUGH RIGHT SIDE KNOCKOUT, (NOTE: SLIDE FROM UNDER PLATE)
INSERT FLUE PIPE ASSEMBLY THROUGH RIGHT SIDE KNOCKOUT,
INSTALL INTAKE COUPLING IN BLOWER SHELF HOLE AS SHOWN. INSTALL INTAKE COUPLING IN BLOWER SHELF HOLE AS SHOWN. INSTALL INTAKE COUPLING IN BLOWER SHELF HOLE AS SHOWN.
INSERT AIR DIFFUSER INTO COUPLING UNTIL TABS ARE SEATED. INSERT AIR DIFFUSER INTO COUPLING UNTIL TABS ARE SEATED. INSERT AIR DIFFUSER INTO COUPLING UNTIL TABS ARE SEATED.
NOTE:
DIFFUSER MAY HAVE A TENDENCEY TO FALL OUT OF THE COUPLING AT DIFFUSER MAY HAVE A TENDENCEY TO FALL OUT OF THE COUPLING AT DIFFUSER MAY HAVE A TENDENCEY TO FALL OUT OF THE COUPLING AT
THIS STEP. tHE INSTALLER MAY ELECT TO INSTALL THE DIFFUSER THIS STEP. tHE INSTALLER MAY ELECT TO INSTALL THE DIFFUSER THIS STEP. tHE INSTALLER MAY ELECT TO INSTALL THE DIFFUSER
AFTER ROTATING THE FURNACE TO THE HORIZONTAL POSITION. AFTER ROTATING THE FURNACE TO THE HORIZONTAL POSITION. AFTER ROTATING THE FURNACE TO THE HORIZONTAL POSITION.
PRE-DRILL (4) 1/8"
HOLES AND ATTACH HOLES AND ATTACH
TYP. (2) PLACES TYP. (2) PLACES
O-RING
7b
INSTALL W/
(2) SCREWS
(NOTE: SLIDE FROM UNDER PLATE).
Ø1/8" HOLES USING THE COLLARS AS A TEMPLATE. Ø1/8" HOLES USING THE COLLARS AS A TEMPLATE.
1/8"
W/ (4) SCREWS W/ (4) SCREWS
ST-A1194-34-01
10c