Audiovox PRO-9675FT Installation Manual page 16

REMOTE START SELECTABLE FEATURES
RF Programmable Features:
Feature Selection
Park Lights Flash 1 x
First
RF start chirp confirm off
Second
10 minute run time
Third Parking lights on steady
Fourth
(No function)
Fifth
(No function)
Sixth
Ignition 2 off during crank
Seventh
Diagnostics off
Eighth
(No function)
Nine Gasoline Engine
Ten
Starter Pole 5X
NOTE:
1) When selecting Diesel operation, (Feature Nine), over gasoline, the only change is to the ignition 1 circuit.
When Diesel is selected, the ignition 1 circuit will power up 10 seconds before the start circuit. The intent
of this feature is to allow the glow plug warming required by some diesel engines. If your vehicle is a
instant start diesel, it is not necessary to activate this feature.
NOTE: When selecting Diesel mode, be certain that the intended vehicle has a true tach reference and be
certain to connect the tach input wire.
2) The difference between selecting Starter Pole 5X or Starter Pole 3X, (Feature Ten), is considering the
time it takes from when the unit reaches the pre-set RPM to when the Starter Motor drops out. This
feature allows fine adjustments when you note a slight overcrank. If after programming tach, the unit
seems to hold the starter engaged slightly longer than necessary, select this feature to pole 3 X. If the
unit starts and the starter drops out properly, (NO OVERCRANK) no change is necessary.
To Program The Remote Start Selectable Features:
1. Start with the valet/program switch in the "Off" position.
2. Turn the ignition key to the On position.
3. Flip the valet/program switch On, Off, On, Off, On, then Off.
4. Immediately turn the ignition key Off then press the RS/Trunk button for 1 second.
5. Immediately turn the ignition key back On.
6. Flip the valet/program switch On, Off, On, then Off. The siren will emit 2 short and 1 long chirp verifying
you are in the feature program mode.
7. Use the Arm/Disarm button on the transmitter to advance to the feature you want to change.
EXAMPLE- If you need to change selectable feature 3, press and release the Arm/Disarm button on the
transmitter 3 times in succession. The parking lights will flash, and the siren will chirp 3 times
confirming that selected feature 3 can be changed.
8. Use the upper left transmitter button to change the selection of the programmable feature. If you are not
sure what the setting for any feature is, press the upper left transmitter button 1 time, the parking lights
will flash once or twice indicating the features setting.
NOTE: Once you've entered the program mode DO NOT allow more than 15 seconds to pass between
steps, or the programming mode will be terminated.
Programming Tach Rate:
2. Programming Tach Rate:
NOTE: All applications require that tach be programmed.
The unit will not operate unless tach is programmed. If an attempt is made to start the vehicle via the remote start
without first programming tach, the unit will flash the parking lights 7 times indicating tach has not been learned and
stored. If the tach rate is not properly programmed to the specific vehicle, the unit may not realize that the vehicle
is running in certain instances reengage the starter motor.
The Remote Start Unit will learn the tach rate of most vehicle's single coil, multiple coil packs, or single
injector. To learn tach.
1. Start with the programming switch in the Off position.
2. Turn the ignition key to the On position.
Park Lights Flashes 2 x
RF start chirp confirm on
15 minute run time
Parking lights flash
Tach operation
(No function)
Ignition 2 on during crank
Diagnostics on
(No function)
Diesel Engine
Starter Pole 3X
16
Default LED Pattern
Off 1 x Pause etc.
10 Minutes 2 x Pause etc.
Steady 3 x Pause etc.
Tach 4 x Pause etc.
---------------- 5 x Pause etc.
Off during crank 6 x Pause etc.
Off 7 x Pause etc.
--------------- 8 x Pause etc.
Gasoline 9 x Pause etc.
Pole 5X 10 x Pause etc.
128-5371
16 of 22