Extron electronics IPCP Pro 250 User Manual page 22

L
TCP/IP
PC
Network
Ethernet
Insert Twisted
Pair Wires
RJ-45
Connector
Pins:
8 7 6 5 4 3 2 1
Rear Panel
or
LAN
Activity
1 2
LED
M
LAN (IP) connectors and LEDs — To connect the IPCP to an Ethernet network
(so you can configure and control the IPCP and the devices connected to it), plug a
cable into one of these LAN RJ-45 sockets and connect the other end of the cable to a
network switch, hub, router, or PC connected to a LAN or the Internet. If the IPCP has
more than one LAN port, the rest of the LAN ports function as simple network switches
(a multiport, unmanaged switch), so that you can connect additional devices to the
same network. For details of communication protocols, ports, and services used, see
Network Port Requirements
Cabling:
For 10Base-T (10 Mbps) networks, use a CAT 3 or better cable.
•
For 100Base-T (max. 155 Mbps) or 1000Base-T networks, use a CAT 5 or better cable.
•
You must configure these ports before using them. Configure the settings via Global
Configurator. See Software-Based Configuration and Control
page 25 of this guide for basic information on configuration.
Activity LED (connector and front panel) — This yellow LED blinks to indicate network
activity.
Link LED (connector and front panel) — This green LED lights to indicate a good
network connection.
1000 LED (front panel) — This green LED lights when the unit is connected to a gigabit
network connection.
Extron Devices
(Switchers, Scalers)
Touchlink Pro
Touchpanel
Straight-through Cable
(for connection to a switch, hub, or router)
End 1 End 2
Pin Wire Color Pin Wire Color
1 white-orange 1 white-orange
2 orange 2 orange
3 white-green 3 white-green
4 blue 4 blue
5 white-blue 5 white-blue
6 green 6 green
7 white-brown 7 white-brown
8 brown 8 brown
TIA/EIA-T568B T568B
Default protocol, public ports:
• IPCP IP address: 192.168.254.250
• Gateway IP address: 0.0.0.0
• Subnet mask: 255.255.255.0
• DNS address: 127.0.0.1
• DHCP: off
• Link speed and duplex level: autodetected
Link
• Data rates: 10/100/1000Base-T
LAN
LED
NOTE: IPCPs with more than one LAN port function as
multiport, unmanaged network switches so you can
connect additional devices to the same network.
Figure 12. LAN Connector and LEDs
Use a straight-through cable for connection to a switch, hub, or router.
•
Use a crossover cable or a straight-through cable for connection directly to a
•
PC. Wire the connector as shown in the tables above.
MAC address — This is the unique user hardware ID number
(MAC address) of the unit (for example, 00-05-A6-05-1C-A0).
You may need this address during configuration.
on page 32.
Crossover Cable
(for direct connection to a PC)
End 1 End 2
Pin Wire Color Pin Wire Color
1 white-orange 1 white-green
2 orange 2 green
3 white-green 3 white-orange
4 blue 4 blue
5 white-blue 5 white-blue
6 green 6 orange
7 white-brown 7 white-brown
8 brown 8 brown
T568B T568A
LAN (Ethernet)
Default login
credentials:
• Username:
admin
• Password:
extron
IPCP Pro Series • Hardware Features and Installation
starting on
Front Panel
LAN
1000 Mbps
Connection
1 2 3
1000
Network is
LINK
active.
ACT
Data is being
sent/received.
MAC
Address
00-05-A6-XX-XX-XX
MAC: 00-05-A6-XX-XX-XX
S/N: ####### E######
16