Table of Contents
Advertisement
SUPERSERVER 2028TP-HTR/HC0R/HC1R-SIOM USER'S MANUAL
Maximum Read Request
Select Auto for the system BIOS to automatically set the maximum size for a read
request for a PCI-E device to enhance system performance. The options are Auto,
128 Bytes, 256 Bytes, 512 Bytes, 1024 Bytes, 2048 Bytes, and 4096 Bytes.
ASPM Support
Use this item to set the Active State Power Management (ASPM) level for a PCI-E
device. Select Auto for the system BIOS to automatically set the ASPM level based
on the system configuration. Select Disabled to disable ASPM support. The options
are Disabled, and Auto.
Warning: Enabling ASPM support may cause some PCI-E devices to fail!
MMIOHBase
Use this item to select the I/O base memory size according to memory-address
mapping for the PCH chip. The base memory size must be between 4032G to
4078G. The options are 56T, 48T, 24T, 512G, and 256G.
MMIO High Size
Use this item to select the high I/O memory size according to memory-address
mapping for the PCH chip. The options are 256G, 128G, 512G, and 1024G.
PCI/PCIX/PCIe Slot 1 OPROM/PCI/PCIX/PCIe Slot 2 OPROM/PCI/PCIX/PCIe
Slot 3 OPROM/PCI/PCIX/PCIe Slot 4 OPROM/
Select Enabled to enable Option ROM support to boot the computer using a de-
vice installed on the slot specified by the user. The options are Disabled, Legacy
and EFI.
Onboard LAN Option ROM Type
Select Enabled to enable Option ROM support to boot the computer using a device
installed on the slot specified by the user. The options are Legacy and EFI.
Onboard LAN1 Option ROM/Onboard LAN2 Option ROM/Onboard Video
Option ROM
Use this option to select the type of device installed in LAN Port1, LAN Port2
or the onboard video device used for system boot. The default setting for LAN1
Option ROM is PXE, for LAN2 Option ROM is Disabled and for Onboard Video
Option ROM is Legacy.
VGA Priority
Use this item to select the graphics device to be used as the primary video display
for system boot. The options are Onboard and Offboard.
7-24
Network Stack
Select Enabled to enable PXE (Preboot Execution Environment) or UEFI (Uni-
fied Extensible Firmware Interface) for network stack support. The options are
Enabled and Disabled.
Super IO Configuration
Super IO Chip AST2400
Serial Port 1 Configuration/Serial Port 2 Configuration
Serial Port 1/Serial Port 2
Select Enabled to enable the onboard serial port specified by the user. The options
are Enabled and Disabled.
Device Settings
This item displays the base I/O port address and the Interrupt Request address of
a serial port specified by the user.
Change Port 1 Settings/Change Port 2 Settings
This feature specifies the base I/O port address and the Interrupt Request address
of Serial Port 1 or Serial Port 2. Select Auto for the BIOS to automatically assign
the base I/O and IRQ address to a serial port specified.
The options for Serial Port 1 are Auto, (IO=3F8h; IRQ=4), (IO=3F8h; IRQ=3, 4, 5,
6, 7, 9, 10, 11, 12), (IO=2F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12); (IO=3E8h; IRQ=3,
4, 5, 6, 7, 9, 10, 11, 12), and (IO=2E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12).
The options for Serial Port 2 are Auto, (IO=3F8h; IRQ=4), (IO=3F8h; IRQ=3, 4, 5,
6, 7, 9, 10, 11, 12), (IO=2F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12); (IO=3E8h; IRQ=3,
4, 5, 6, 7, 9, 10, 11, 12), and (IO=2E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12).
Serial Port 2 Attribute
Select SOL to use COM Port 2 as a Serial_Over_LAN (SOL) port for console redi-
rection. The options are COM and SOL.
Serial Port Console Redirection
COM 1
COM 1 Console Redirection
Select Enabled to enable COM Port 1 Console Redirection, which will allow a client
machine to be connected to a host machine at a remote site for networking. The
options are Disabled and Enabled.
7-25
Chapter 7: BIOS
Advertisement
Table of Contents
