Mytee 8070 Lite Instructions Manual page 5

a
8070 MYTEE LITE™ FEATURES
a
a
a
a
a
a
a
a
a
a
7
1. Hose hanger
2. Recovery tank lid
3. Cuff-Lynx™ vacuum hose connector
4. Open fill for solution tank
5. Solution hose connector
6. Solution tank drain
M.LaBarbera
DRAWN
7. Solution tank faucet fill
CHECKED
COMMENTS:
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
2
6 5
QTY. MSRP
1 $4.99 ea
1 $15.99 ea
1 $9.99 ea
3
8400 - 4" Stainless Steel
Upholstery Tool
2
1
H122 Cuff-Lynx™ - 2"
Female Reducer
6 5
FRONT
1
2
6
mytee
NAME DATE
PRODUCTS, INC.
1/2014
858-679-1191
TITLE:
MyteeLite II
(2014)
SIZE DWG. NO.
ACCESSORIES C
8070
F
SCALE: 1:24
DO NOT
SCALE DRAWING
1
4 3 2
REVISIONS
REV. DESCRIPTION
OD ORIGINAL DRAFT
E
D
850 1 - 15' 1-1/4"
Hose-n-Hose™ Vacu-
um/Solution Hose
C
B
A
A110 Drain Hose
NAME DATE
M.LaBarbera 9/2015
DRAWN
CHECKED
COMMENTS:
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
4
3 2
8 7
F
D
E
C
D
3
4
C
B
5
14
B
8. Basket
9. Recovery tank drain hose
10. Service latch
A
11. Switch plate
12. 25' single power cord
13. 6" wheels
14. 2" casters
8 7
A
8 7 6
REV
E
SHEET 1 OF 3
1
DATE APPROVED
9/1/2015 JFL
F
E
D
C
B
In the rear of the machine, with handle/basket facing
outward, line up the four inserts on the handle with the
four inserts on the machine, located on the top sides of the
recovery tank. When installing the handle on your new
mytee
PRODUCTS, INC.
858-679-1191
TITLE:
Mytee Lite™, make sure you use a hand tool (screwdriver)
Drain hose w/plug,
A
8070
for the screws and NOT a power tool. This will insure you
SIZE DWG. NO. REV
8 7 6
C A110
OD
do not strip the hole and puncture the recovery tank.
SCALE: 1:2 DO NOT SHEET 1 OF 1
SCALE DRAWING
1
5
6 5
BACK
13
12
6 5
5 4 3
CONNECTING THE HANDLE
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
5 4 3
4 3
REV.
OD
8
9
10
11
UNLESS OTHER
DIMENSIONS A
TOLERANCES:
ANGULAR: MA
ONE PLACE D
TWO PLACE D
THREE PLACE D
MATERIAL
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE FINISH
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
4 3
2 1
REVISIONS
REV. DESCRIPTION DATE APPROVED
OD ORIGINAL DRAFT JFL
UNLESS OTHERWISE SPECIFIED: NAME DATE mytee
PRODUCTS, INC.
1/2014
DIMENSIONS ARE IN INCHES V. LaBarbera
DRAWN
858-679-1191
TOLERANCES:
TITLE:
CHECKED
ANGULAR: MACH .5
MyteeLite II (2014
COMMENTS:
ONE PLACE DECIMAL .03
TWO PLACE DECIMAL .05
THREE PLACE DECIMAL .003
MATERIAL
SIZE DWG. NO. REV
C 8070 (2014)
E
FINISH
SCALE: 1:8 SHEET 1 OF
DO NOT
SCALE DRAWING
2 1