Download Print this page

English Gb - Honeywell HW223E Operating Instructions Manual

Radiant panel heater
Hide thumbs

Advertisement

ENGLISH GB

IMPORTANT SAFETY INSTRUCTIONS
Read through all the instructions before
starting to use the appliance. Keep this manual
in a safe place for future reference.
These instructions are also available on our
website. Please visit www.hot-europe.com.
• This appliance must only be operated as
instructed in this user manual.
• This appliance can be used by children
aged from 8 years and above and persons
with reduced physical, sensory or mental
capabilities or lack of experience and
knowledge if they have been given
supervision or instruction concerning use of
the appliance in a safe way and understand
the hazards involved. Children shall not play
with the appliance.
• Children of less than 3 years should be kept
away unless continuously supervised Children
aged from 3 years and less than 8 years shall
only switch on/off the appliance provided
that it has been placed or installed in its
intended normal operating position and they
have been given supervision or instruction
concerning use of the appliance in a safe
way and understand the hazards involved.
Children aged from 3 years and less than 8
years shall not plug in, regulate and clean the
appliance or perform user maintenance.
• CAUTION — Some parts of this product can
become very hot and cause burns. Particular
attention has to be given where children and
vulnerable people are present.
• Never position this appliance immediately
underneath a power socket.
• Do not use this heater in the immediate
surroundings of a bath, a shower or a
swimming pool.
DO NOT COVER WARNING: In order to
avoid overheating, do not cover the heater
with anything, as indicated by the symbol.
This can lead to overheating, fire or electric
shocks. Ensure that the air intake and outlet
vents are not obstructed.
• The appliance is intended only for use indoors,
not for outdoor use or commercial use.
4
• Do not use the appliance anywhere near
easily flammable gases or substances such
as solvents, lacquers, glues, etc. Some of the
internal parts can be hot and could throw
sparks.
• Keep flammable materials at least 100cm
away from the heater. To prevent burns, do
not allow bare skin to come in contact with
hot surfaces.
• If the supply cord is damaged, it must be
replaced by the manufacturer, its service
agent or similarly qualified persons in order
to avoid a hazard.
• Never touch the unit with wet hands.
• Check for any obstructions. If you find an
obstruction, turn off the heater using the
power button on the control panel. Allow
the heater to cool completely, then remove
the obstruction. Wait at least 10 minutes,
then turn on the heater and follow the
instructions for use.
COMPONENTS
(See page 2)
1.
Air inlet grille
2.
Air outlet grille
3.
Power setting knob
4.
Thermostat knob
5.
Handles
6.
Feet
7.
Feet assembly screws
8. Wall mounting clips
9.
Wall mounting screws and rawl plugs (for concrete)
10. Wall spacers
11. Power cable
ASSEMBLY
(See page 3)
This heater may be used with feet on the floor or attached directly to the wall.
FOOTSTAND INSTALLATION
1. For floor use, attach the feet to the lower part of the heater by snapping each foot
into the matching holes (fig. 1). Respect the "L" (left) and "R" (right) positions for
the feet.
2. As shown in fig. 1A, please tighten the feet at the bottom of the heater using the
feet assembly screws provided.
3. Place the heater on a firm, level, open surface at least 90cm away from any other
object. DO NOT use on an unstable surface such as bedding or deep carpeting.
WALL MOUNTING INSTALLATION
1. For wall mounting, find a position for the heater ensuring proper clearances (fig. 3).
2. Secure the wall mounting clips into the wall using the wall mounting clip screws
and rawl plugs (for concrete) provided (fig. 4).
3. Attach the wall spacers on the back of the heater to keep the minimum distance
to the wall. Attach the heater to the mounting clips, using the mounting holes on
the back of the heater (fig. 2).
POWER CABLE WINDING
(See page 3)
• If you want to wind the power cable on the heater when not in use, mount the wall
spacers at the rear side of the heater.
• Wind the power cable around the wall spacers (fig. 5).
• When you wish to use the heater, you must completely unwind the power cable. An
incompletely unwound power cable can lead to overheating and cause a fire.
OPERATING INSTRUCTIONS
(See page 2)
• Turn the power setting knob counterclockwise to the (š) position.
• Plug the heater power cable into an outlet.
• Turn the power setting knob to the desired power setting (fig. 6):
= Low – 600W
= Medium – 900W
= High – 1500W
• Turn the thermostat knob clockwise to the highest temperature setting for rapid
warming.
• When the room reaches a comfortable temperature, turn the thermostat knob
counterclockwise until the heater switches off (a click is heard and the pilot light
goes off). At this setting, the thermostat will automatically turn the heater on (the
pilot light illuminates) and off (the pilot light goes out) to maintain the selected
temperature.
• To turn the heater off, turn the power setting knob to the (š) position and unplug the
heater.
AUTOMATIC ANTI-FROST FUNCTION
The heater is equipped with an automatic anti-frost function. Plug in the heater. Turn
the power setting knob to any of the active settings ( , or ). Turn the thermostat
knob counterclockwise to its lowest setting, indicated by the snowflake icon ( ).
As soon as the room temperature is below + 5° C the heater will automatically switch on.
As the heater will automatically turn on in anti-frost mode, make sure the heater is not
covered or obstructed by any object.
AUTOMATIC SAFETY CUT-OUT
This heater is equipped with an automatic safety cut-out. If the heater stops
unexpectedly, the safety cut-out may have operated. Once the safety cut-out has
operated, the heater will not restart until the heater has been turned off and cooled
down. In this situation, you must turn the power setting knob to the (š) position and
unplug the heater. Allow the heater to cool, then follow the "Operating Instructions".
TIP-OVER SWITCH
The heater is equipped with an automatic tip-over switch that will disable the heater if it
is accidentally tipped over.
IF THE HEATER FAILS TO OPERATE
• Check for and remove any obstructions.
• Check if the heater is in the standing position.
• Check if the heater is plugged in. Also check if the power socket is working
(e.g. plug in a different working electrical device).
• Make sure that the thermostat is not set too low. With the power setting knob set to
one of the active settings ( , or ) turn the thermostat knob clockwise until the
heater turns on again (pilot light illuminates).
• If the heater still does not work, consult the warranty for further instructions.
CLEANING
We recommend you to clean the appliance twice a year (or before if you notice
performance to be impaired) with a vacuum cleaner.
1.
Unplug the unit.
2.
Allow it to cool down for 20 minutes.
3.
Use a vacuum cleaner to suck out dust and dirt from both grilles.
MAINTENANCE
In the event of overheating, the safety system will automatically turn off the heating
elements and/or the motor, if any. If this happens please remove any obstacles to the air
outlet grille and clean the unit as indicated under cleaning instructions.
ENGLISH GB
DISPOSAL
This appliance complies with EU legislation 2012/19/EU on end of life recycling.
Products showing the 'Crossed Through' wheeled bin symbol on either the
rating label, gift box or instructions must be recycled separately from
household waste at the end of their useful life.
Please DO NOT dispose of appliance in normal household waste. Your local appliance
retailer may operate a 'take-back' scheme when you are ready to purchase a replacement
product, alternatively contact your local government authority for further help and
advice on where to take your appliance for recycling.
CONDITION OF PURCHASE
As condition of purchase the purchaser assumes responsibility for the correct use and
care of this Kaz product according to these user instructions. The purchaser or user must
himself or herself decide when and for how long this Kaz product is in use.
WARNING: IF PROBLEMS ARISE WITH THIS KAZ PRODUCT, PLEASE OBSERVE THE
INSTRUCTIONS IN THE GUARANTEE CONDITIONS. DO NOT ATTEMPT TO OPEN OR
REPAIR THE KAZ PRODUCT YOURSELF, AS THIS COULD LEAD TO TERMINATION OF
THE GUARANTEE AND CAUSE DAMAGE TO PERSONS AND PROPERTY.
This product carries the CE mark and is manufactured in conformity with the
Electromagnetic Directive 2004/108/EC, the Low Voltage Directive 2006/95/EC and the
RoHS Directive 2011/65/EU.
Technical modifications reserved
HW223E
220-240V ~ 50Hz
1500W
This product is only suitable for
well-insulated spaces or occasional use.
5

Hide quick links:

Advertisement

loading

  Also See for Honeywell HW223E