Prepare For Self-Clean And Delayed Self-Clean Cycle; Self-Cleaning; Delayed Self-Clean Cycle; Adjusting Oven Temperature - Viking VEDO 273 Service Notebook

PROGRAMMING INSTRUCTIONS--ERC5800
Prepare for Self-Clean and Delayed Self-Clean
• A small amount of smoke is normal when cleaning.
Excess smoke may indicate a faulty gasket or too
much food residue has been left in oven. Move birds
and small animals susceptible to fumes or smoke to
another room.
• Do not use cleaning cycle if oven light cover is not
properly in place.
• Remove oven racks and all cooking utensils from
oven.

Self-Cleaning

Self-clean feature uses high oven temperature to clean
oven interior.
1. Prepare oven for self-cleaning.
2. Press CLEAN pad.
3. Press + or - pad to adjust desired amount of cleaning
time.
• Increase or decrease cleaning time by 5 minutes
increments.
• Clean can be set from 2 to 4 hours. Minimum
recommended cleaning time is 3 hours.
• "LOCK" flashes while oven door is locking and
remains in display while door is locked.
• Oven begins to clean automatically.
• After oven has cooled to a safe temperature,
"LOCK" no longer displays and door is unlocked.

Delayed Self-Clean Cycle

Self-clean features uses high oven temperature to clean
oven interior. Set oven to begin and end cleaning at
later time. Control calculates back from end time to
determine starting time.
1. Prepare oven for self-cleaning.
2. Press CLEAN pad.
3. Press + or - pad to adjust desired amount of cleaning
time.
• Increase or decrease cleaning time by 5 minute
increments.
• Clean can be set from 2 to 4 hours. Minimum
recommended cleaning time is 3 hours.
4. Press STOP TIME pad.
5. Press + or - pad until desired stopping time appears
in display.
• Starting time is automatically calculated back based
Cycle
on amount of cleaning time and stop time. Oven
begins to clean automatically.
• "LOCK" flashes while oven door is locking and
remains in display while door is locked.
• To view remaining cleaning time, press and hold
CLEAN pad.
• To view calculated stop time, press and hold
STOP TIME pad.
• After oven has cooled to a safe temperature,
"LOCK" no longer displays and door is unlocked.
Interrupt Self-Clean Cycle
1. Press OFF CANCEL pad.
2. After oven has cooled to a safe temperature, door
can be opened.

Adjusting Oven Temperature

Oven temperature has been factory calibrated and
tested.
overcooks or undercooks food, oven temperature can be
adjusted.
1. Press BAKE pad.
2. Press + until an oven temperature greater than
500°F shows in display.
3. Immediately press and hold BAKE pad until "00"
appears in display, approximately 5 seconds.
4. To decrease oven temperature (for cooler oven),
press - until negative numbers appear. Oven can be
set from -05° to -35° lower.
adjusting oven move temperature -05° each time.
5. To increase oven temperature (for warmer oven)
press + until positive numbers appear. Oven can be
set from 05° to 35° higher. To avoid over adjusting
oven, move temperature 5° each time.
6. Press OFF CANCEL pad. Temperature adjustment
will be retained even through a power failure.

Service Tones and Codes

Electronic range control has a self diagnostic system.
Self diagnostic system sounds a series of short, rapid
beeps and shows an "F-code" in display when there is a
problem. When electronic range control signals a
problem, follow steps listed below.
1. Record "F-code" shown.
• See, Digit Failure Display in "ERC Warnings
and Failure Codes" section.
2. Disconnect electrical supply.
• Pressing OFF CANCEL pad or disconnecting
electrical supply may eliminate "F-code". If
failure continues, contact and authorized servicer
to check oven.
26
In unlikely event that oven consistently
To avoid over