Table of Contents
Advertisement
Owner's Manual
Connecting Your Model 970
Connecting Audio Components
CD Player or Music Server
Connect the L and R channel outputs on the CD player or music server
Analog
to the CD input jacks (
).
RP15
If your CD player or music server has a digital output, connect it to
Digital
one of the coaxial or optical inputs (RP9) depending on the type of connector
used by the source. (You'll configure the Model 970 later to use the input you've
chosen. For now, note that digital input on your system chart.)
Audio Recorder
(Cassette deck, MD recorder, DAT, CD recorder, etc.)
Connect the L and R audio outputs on the recorder (usually marked
Analog
PLAY) to the TAPE IN jacks (
RP15
marked REC) to the RECORD OUT/TAPE jacks (
Connect your recorder's digital output jack to either the coaxial or
Digital
optical input (
) depending on the type of connector used by your recorder.
RP1
(As with the digital CD input, configuration will come later. For now, just note
that input on your system chart.)
If your recorder has a digital input jack, connect it to either the coaxial or opti-
cal output (
RP1
) depending on the type of connector used by your recorder.
(Configure this later, but note the connection now.)
Computer sources
NOTE: Although you can connect a computer via analog or digital
inputs, we suggest a PCM, Dolby Digital or DTS connection when pos-
sible for the best sound. You can also use your computer to record
sound from the other devices connected to the Model 970.
Analog
Using a 1/8" (3.5mm) stereo miniplug to dual-RCA adapter cable (a
"Y" cable with male connectors at both ends), connect the computer sound
card's audio output minijack to the TAPE IN jacks (
ond "Y" cable, connect the sound card's audio input minijack to the RECORD
OUT/TAPE jacks (
).
RP15
NOTE: If you have to make a choice between connecting another
recording device or your computer through analog connections, opt to
use the analog jacks for the other recording device.
Connect your sound card's digital output jack to either the coaxial or
Digital
optical input (
) depending on the type of connector used by the sound
RP1
card. (As with the digital CD input, configuration will come later. For now, just
note that input on your system chart.)
If your sound card has a digital input jack, connect it to either the coaxial or
optical output (
) depending on the type of connector used by the sound
RP1
card. (You'll configure this later but note the connection now.) Note, however,
that the signal must be output from the computer in a form that is compat-
ible with the Model 970's signal processing, such as Dolby Digital, DTS or
conventional PCM. Other digital audio formats such as MP 3 may not be used
directly with the Model 970.
16
Outlaw Audio
(see page 19)
). Connect the L and R audio inputs (usually
).
RP15
). Then, using a sec-
RP15
MP3 Player
You can use any analog audio input to connect an MP3 player to the
Analog
Model 970 but you'll probably find it most convenient to use the Left and Right
channel analog audio jacks on the front panel Video 4 input (
same 1/8" (3.5mm) stereo miniplug to dual-RCA adapter cable (a "Y" cable
with male connectors at both ends) that we've suggested above to go from the
MP3 player's headphone output to the Model 970. Remember the color-coding
on the RCA end of the cable – red for right, white for left.
Connecting Video Components
Before making connections to any video devices, you should understand how
the Model 970 routes video signals.
Any signal appearing at any composite video input (DVD, VIDEO 1-4 IN) is
automatically sent to the composite and S-Video VIDEO MONITOR OUT and
VIDEO 1 REC OUT jacks and to the component MONITOR OUT jacks.
Any signal appearing at any S-Video input jack (DVD, VIDEO 1-4 IN) is auto-
matically sent to the composite and S-Video VIDEO MONITOR OUT and VIDEO
1 REC OUT jacks and to the component MONITOR OUT jacks.
Any signal appearing at the component video (DVD, VIDEO 1-2 IN) input jacks
is automatically sent to the component video MONITOR OUT jacks only.
Any signal appearing at either the DVI 1 or DVI 2 input is sent to the DVI OUT
jack only.
NOTE: For the greatest flexibility, connect composite or S-Video cables
from all of your video source components to the Model 970, even if
you are already using a component video or DVI connection.
Remember that the Model 970's on-screen display does not appear at the DVI
OUT jack so always provide a component, S-Video, or composite video connec-
tion in addition to DVI.
DVD Player
This is a complex bit of interconnectivity simply because there are many pos-
sibilities. You'll have to deal with several video signal formats and a variety of
audio possibilities, too. So read this section carefully before you begin.
Video Connections
Using a video cable with yellow RCA jacks at both ends, connect the
Composite
DVD player's composite video output to the composite video DVD input (
NOTE: You may be tempted to use standard audio "patch cords" for
composite video connections. Resist that temptation. The impedance
specification of audio cables is not the same as for video and you may
see image degradation as a result.
Using a S-video cable with a 4-pin mini-DIN connector at each end,
S-Video
connect the DVD player's S-video output to the S-video DVD input (
S-Video delivers a better picture than composite connections and should be
used whenever possible unless component or DVI connections are available.
They deliver better pictures than S-Video.
). Use the
FP18
(see pages 20-22)
).
RP5
).
RP5
Advertisement
Table of Contents
