Connecting Audio Components; Cd Player; Audio Recorder; Connecting Video Components - Outlaw 950 7.1 Owner's Manual

Connecting Audio Components

CD Player

Connect the L and R channel outputs on the CD player to the CD IN
Analog
jacks on the Model 950.
If your CD player has a digital output jack, connect it to one of the
Digital
coaxial (COAX 1 or 2) or optical (OPT 1-4) input jacks on the preamp/processor,
depending on the type of connector used by the CD player. Later, you will con-
figure the Model 950 to use the specific input that you have chosen. For now,
note which digital input you connected to on your system chart.

Audio Recorder

A recording device such as a cassette deck, MD recorder, DAT deck or CD
recorder can be connected to the Model 950 using either or both of the fol-
lowing methods.
Connect the L and R audio outputs on the recorder (usually marked
Analog
PLAY) to the TAPE IN jacks on the rear of the preamp/processor and connect
the L and R audio inputs (usually marked REC) to the TAPE OUT jacks of
the Model 950.
If your recorder has a digital output jack, connect it to one of the
Digital
coaxial (COAX 1 or 2) or optical (OPT 1-4) input jacks on the preamp/processor,
depending on the type of connector used by the device. Later, you will configure
the Model 950 to use the specific input that you have chosen. For now, note
which digital input you connected to on your system chart.
If your recorder has a digital input jack, connect it to either the coaxial or opti-
cal output jack on the preamp/processor. The signal from the selected digital
input source of the Model 950 will be sent to the recorder.

Connecting Video Components

Before making connections to any video devices, it will help to understand
how the Model 950 routes the video portion of the signal through its video
section.
Any signal that appears at one of the composite video input jacks (DVD,

VIDEO 1, 2 or 3) is automatically sent to the composite video OUT and
VCR OUT jacks, as well as the S-Video OUT and VCR OUT jacks.
Any signal that appears at the S-Video input jacks (DVD, VIDEO 1, 2 or

3) is automatically sent to the S-Video OUT and VCR OUT jacks, as well
as the composite video OUT and VCR OUT jacks.
Any signal that appears at the component video (DVD or VIDEO 1) input

jacks is automatically sent to the component video MONITOR OUT con-
nection only.
NOTE: To provide the greatest signal flexibility, be sure to connect
all available types of inputs and outputs from your video devices. For
example, if only the composite video output (yellow RCA jack) con-
nection is made to your display device, component sources will not be
available, even if they are connected to the Model 950.

DVD Player

Connect the composite video output from the DVD player to the DVD
Composite
video input jack on the rear of the Model 950 using an RCA-type video cable.
If there is an S-Video output on the DVD player, and you have an S-
S-Video
Video input on your TV or monitor, connect it to the S-Video DVD input on the
rear of the Model 950 using an S-Video cable. S-Video delivers a better picture
than composite connections and should be used whenever possible unless you
can use component connections, which deliver better video than S-Video.
If the DVD player has component video outputs, connect them
Component
to the DVD component video input jacks on the rear of the Model 950 using
an appropriate cable set.
Connect the L and R channel outputs on the DVD player to
Analog Audio
the DVD IN audio jacks on the rear of the Model 950.
Connect one of the digital output jacks on the DVD player to
Digital Audio
one of the coaxial (COAX 1 or 2) or optical (OPT 1-4) input jacks on the rear
of the preamp/processor, depending on the type of connector used by the DVD
player. Later, you will configure the Model 950 to use the specific input that
you have chosen. For now, note which digital input you connected to on your
system chart.
If your DVD player supplies a multi-channel audio
Multi-channel Audio
output (for DVD Audio or SACD playback), connect the six outputs (special cable
sets for this are available from numerous sources, including Outlaw Audio)
from your player to the six input jacks labeled MULTI CHANNEL INPUT on
the rear panel of the Model 950. Be sure match the connections—left to left,
right surround to right surround, and so on. If your player includes a built-in
Dolby Digital decoder and has 5.1 channel analog audio outputs we suggest
that you do not use them, but use the digital audio connection and the Model
950's internal decoders instead.
If you are connecting a DVD-Audio or SACD player to the Model 950 using these
jacks, you will need to consider the setting for the Analog Bass Management
switch on the Model 950's rear panel. If your system uses all full range speak-
ers, set the switch in the OFF position. In that setting the signal will be routed
directly from the input jacks to the volume control.
However, if your system uses small, frequency-restricted satellite speakers, the
switch should be set to the ON position. In that setting the signals sent to the
main speakers will be cut at 80 Hz and a summed bass signal will be sent to
the subwoofer output. Note that you should place this switch in the OFF posi-
tion if your playback source includes internal bass management circuitry or
if you use an external bass manager such as Outlaw's ICBM-1 between the
player and the Model 950.
Owner's Manual
Connecting Your Model 950
Model 950 7.1 Channel Preamp/Processor
19