Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Outlaw 7000x
Summary of Contents for Outlaw 7000x
- Page 1 Model 7000x Seven Channel Power Ampli er model 7000x...
- Page 3 IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with manufacturer’s instructions. 8.
-
Page 4: Please Read First
IMPORTANT SAFETY NOTE Before connecting a new component height required for proper ventilation, and must not be removed. such as the Model 7000x to your audio or home theater system it is always Power Sources The unit should be operated only from the type of Ô... -
Page 5: Table Of Contents
Outlaw Audio, LLC. A Few Words About Hum and Noise Protection Mode Outlaw Audio and the Outlaw Audio logo are registered trademarks of Outlaw Audio, LLC. The Outlaw Audio 30-Day Satisfaction Guarantee Outlaw Audio Limited Warranty tion to modify existing units. -
Page 6: Features
Model 7000x Rear Panel Before you Begin The Outlaw 7000x is a state of the art, high performance, were specially designed to cushion it from shocks and vibration during transit. We require you save these materi- mentary circuitry from input to output. -
Page 7: Rear Panel
Use this jack to connect to a compatible processor or other product with a 3.6 - 32 Volt DC output. AC Input (see page 9) Use this input to connect the Model 7000x to an AC Manual/Trigger Power Switch (see page 9) power source with the supplied power cord... -
Page 8: Input Connections
(or other source equipment) to the input jacks on the rear panel of the Model 7000x that have the same Be sure to maintain the correct polarity between your of clarity or resolution, we recommend that you use high- channel name. - Page 9 Once all of the connections have been made to the rear bare wire: spade lugs: panel of the Model 7000x, run the cables to the speaker locations. We recommend using similar wire lengths to each Strip approximately 1/2 to 3/4 inch (20mm) of Loosen the knob of the desired speaker output pair of speakers.
-
Page 10: Remote Trigger Connection
Model 7000x turns on and the blue ring glows or other audio equipment. brightly. same AC power circuit as the Model 7000x, unless they are used Connect the 3.5mm mini-plug from the AC adapter with the remote power turn on and sequencing system. The... -
Page 11: Manual Operation
Trigger and the 3.5mm cable should be inserted to the Model When operating the Model 7000x you should not place 7000x and the source device as described on page 8. The blue ring To power the Model 7000x on and o using the Ô... -
Page 12: Cleaning
30 minutes for the unit to cool down and reset the front LED. The unit should be cool to the touch when its ready to be turned back on. If after waiting the light does not glow blue again, please call Outlaw customer service. Improper settings or output levels from the processor or controller Check the settings on your preamp, processor or controller. -
Page 13: A Few Words About Hum And Noise
DC voltage on an input connection or thermal overload, operating. the Outlaw 7000x will place itself in a protect mode to event that a fuse replacement is required, be certain that a prevent damage to the ampli er. When this happens fuse of the original rating is used. -
Page 14: The Outlaw Audio 30-Day Satisfaction Guarantee
4 - 24 Volts DC at 5 milliamperes or Ô determine if there is a quick solution to your problem. greater Outlaw Audio shall not be liable for, or in any way respon- Damage occurring during shipment General Ô sible for, any incidental or consequential damages of any Dimensions including 5.8215...
Need help?
Do you have a question about the 7000x and is the answer not in the manual?
Questions and answers