Timer Operation - Sanyo DC-MCR60 Instruction Manual

Recording copyright material without permission of the copyright
owners is usually an infringement. If you wish to re-record copy-
right material, permission from the copyright owner is necessary .
SANYO does not approve of, and cannot be held responsible for,
any unlawful use of this machine.
Recording compact discs (Synchronous recording)
1. Push the cassette lid backward.
2. Load a blank cassette.
3. Select "CD" function.
4. Load the disc to be recorded.
- Select the track number if required.
- For programmed recording, programme the material in ad-
vance (as described under "PROGRAMMED PLAY").
5. Press the REC button. The PLAY button is engaged simultaneously
and CD recording starts.
- When you want to record music as you listen, press the REC
button. Recording starts automatically from the beginning of
the track.
6. Press the STOP/EJECT button to stop recording.
When the end of the tape is reached, the CD player and deck stop
automatically.
Recording from the tuner
1. Push the cassette lid backward.
2. Load a blank cassette.
3. Tune in the radio station to be recorded.
4. Press the REC button to start recording.
5. Press the STOP/EJECT button to stop recording.
Using the timer (Main unit only)
Set the on and off times, and function to be used. Operation will start
with the selected function at the on time. The sound will be gradually
increased from a no-sound level to the current volume setting (fade-
in). The power will be switched off at the off time.
The timer will function every day unless it is released.
Note:
Make absolutely sure that the clock is set to the correct time before
setting the timer.
Operation
1. Press the FUNCTION button to select the function and set the
desired volume level for timer operation.
2. Press the CLOCK/TIMER button for at least 2 seconds.
The previous timer on time setting appears.
3. Press the MEMORY button within 10 seconds.
4. Set the timer on time by turning the VOLUME control, then press
the MEMORY button (as described under "ADJUSTING THE
CLOCK").
The timer off time setting appears.
5. Set the timer off time as described in step 4.
The previous function setting appears.
- "0" remains lit.
RECORDING
When beat is heard
Beat (a high-pitched noise) may sometimes be heard during the re-
cording of radio broadcasts. If this occurs, while the MEMORY button
is pressed, press the TUNING + button at the same time to select bc-
1 or bc-2. Select the setting that gives the best result.
Safeguards against accidental erasure
Accidental erasure can be prevented by breaking out the tabs on the
end of the cassette tape (where the tape is not exposed) using a screw-
driver or similar implement.
If a tab is broken out in error and you wish to re-record the tape,
simply block the tab hole using adhesive tape and the tape can be
used for recording again.

TIMER OPERATION

6. Press the z/ON button to switch off the power.
To release the timer
After turning the power on, press the CLOCK/TIMER button twice,
"0" disappears.
To set the timer again with the same settings
1. Press the CLOCK/TIMER button repeatedly to display "0".
2. Press the z/ON button to switch off the power.
Note:
The timer operation is released if a power failure occurs.
Using the sleep timer
The sleep timer automatically switches off the power after a preset
time has elapsed. The volume will gradually be reduced (fade-out)
during the 1-minute period before the unit turns off. There are 12 time
periods available: 120, 110, 100, 90, 80, 70, 60, 50, 40, 30, 20, and 10
minutes.
Press the SLEEP button repeatedly to select the desired sleep time.
"SLEEP" blinks and the selected time appears on the display. After a
few seconds, the original display returns. "SLEEP" remains blinking.
To check the remaining sleep time
Press the SLEEP button once. After a few seconds, the original dis-
play return.
To release the sleep timer while in operation
Press the SLEEP button repeatedly until "SLEEP" disappears. The
timer is also released if the power is switched off.
-7-
Side A
Break out tab A for side A.
Break out tab B for side B.
- To switch off the power during a timer controlled operation, press
the z/ON button. The timer will be set in the standby mode.
(Remote control only)
Side B